1. Home
    2. /
  2. Manuals
    3. /
  3. Novatel Wireless
    4. /
  4. MIFI-4510L
    5. /
  5. 16
Page 76 / 88 Scroll up to view Page 71 - 75
71
How do I reset the Access Point and Router settings back to factory settings?
To reset the access point and router settings, follow these steps:
➊
Connect to MiFi Settings by connecting your computer to the MiFi wireless network and
going to
http://admin.mifi
or
in your browser.
➋
Connect to the Diagnostics screen. (See
Diagnostics
on page 61.) The Diagnostics screen
has a
Reset to Factory Defaults
button. This button resets all Access Point and Router
settings to their factory default values. All existing settings are lost.
The password on or inside the device does not work. What should I do?
Your SSID and Wi-Fi Admin password appear on the back of your device. If you do not have a
password label on the back of your MiFi 4510L, follow these steps:
➊
Open the device and use the password printed on the password label underneath the
battery.
➋
If the password on or inside the device does not work, call Customer Service at
1-800-786-8419
.
Page 77 / 88
72
Customer Service
For Customer Service while in the U.S. or Canada, contact Verizon Wireless at 1-800-786-8419.
Data Technical Support
For additional information and technical support for Verizon Wireless devices, you can visit the
Verizon Wireless Data Technical Support page at
.
Page 78 / 88
Product Specifications
Regulatory Statements
Wireless Communications
Limited Warranty and Liability
Safety Hazards
Proper Battery Use and Disposal
Product Specifications and
Regulatory Information
5
Page 79 / 88
74
Product Specifications
General
Name:
Verizon Jetpack
™
Mobile Hotspot - MiFi® 4510L
Model:
MiFi 4510L
Approvals:
FCC (North America); IC (Canada)
Weight:
85 g / 3 oz
Dimensions:
90 mm x 60 mm x 13 mm,
3.54 in x 2.36 in x 0.51 in
Wireless Network – Dual Mode:
LTE, CDMA 1X/EV-DO Rev A
Wireless Network –
Wi-Fi Mode
802.11 b/g/n
Default SSID
Verizon MIFI4510L XXXX Secure (see the
sticker on the back of your device or on
the front of your Connect Card for your
SSID and Wi-Fi/Admin password)
Battery
•
Size
•
Time required for full charge
1500 mAh
2.5-3 hours (when not in use)
Chip Set:
QUALCOMM® MDM9600
Interface Type:
Type B USB Port for micro USB, used by
the wall charger
Technology/Bands
Technology:
LTE, CDMA Rev A, Rev 0, 1XRTT
Band Designation:
LTE 700 MHz
CDMA 1x/EV-DO RA; 800/1900 MHz
Transmit Band:
824.7-848.31 MHz/1851.25-1908.75 MHz
Receive Band:
869.7-893.31 MHz/1931.25-1988.75 MHz
Environmental
Operating Temperature:
-10 ° C to +45° C (14°F to 113° F)
Storage Temperature:
-20° C to 60° C (-4° F to 140° F)
Drop:
1 meter (3.28 feet) drop, no damage – fully operational
Vibration Stability:
5 Hz to 500 Hz, 0.1 octave/second
Page 80 / 88
75
Regulatory Statements
Federal Communications Commission (FCC) and Industry Canada (IC) Notice
Electronic devices, including computers and wireless modems, generate RF energy incidental to their
intended function and are therefore subject to FCC rules and regulations.
This equipment has been tested to, and found to be within the acceptable limits for a Class B digital device,
pursuant to part 15 of the FCC Rules and Industry Canada ICES-003. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a residential
environment.
This equipment generates radio frequency energy and is designed for use in accordance with the
manufacturer’s user manual. However, there is no guarantee that interference will not occur in any particular
installation. If this equipment causes harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, you are encouraged to try to correct the interference by
one or more of the following measures.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules and with Industry
Canada ICES-003. Operation is subject to the following two conditions.
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause undesired
operation.
WARNING:
DO NOT ATTEMPT TO SERVICE THE WIRELESS COMMUNICATION DEVICE YOURSELF. SUCH ACTION MAY
VOID THE WARRANTY. THE MiFi 4510L MODEM IS FACTORY TUNED. NO CUSTOMER CALIBRATION OR TUNING IS
REQUIRED. CONTACT NOVATEL WIRELESS TECHNICAL SUPPORT FOR INFORMATION ABOUT SERVICING YOUR WIRELESS
COMMUNICATION DEVICE.
FCC CAUTION
: Any changes or modification not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
MODIFICATIONS:
The FCC requires that you be notified that any changes or modifications made to this device that are
not expressly approved by Novatel Wireless, Inc. may void your authority to operate the equipment.
NOTE:
The Radio Frequency (RF) emitter installed in your modem must not be located or operated in conjunction with
any other antenna or transmitter, unless specifically authorized by Novatel Wireless Technologies.
RF Exposure Content
FCC Equipment Authorization ID
:
PKRNVWMIFI4510
Industry Canada Certification Number: 3229B-MIFI4510
Model: MIFI4510L
This device is authorized for use in mobile and portable applications. At least 12 mm (0.5 inches) of
separation between the antenna and the user’s body must be maintained at all times.
This product has been evaluated for SAR and meets the FCC and IC Guidelines for exposure to radio waves.

Rate

4 / 5 based on 1 vote.

Popular Novatel Wireless Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top