1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WPN802v2

NETGEAR WPN802v2 Router Manual PDF (Setup & Configuration Guide)

Given below is full router user manual of NETGEAR WPN802v2 router model. You can also download this manual in PDF Format to read later on your computer.

Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.

Page 1 / 2
)NSTALLATION 'UIDE
NETGEAR WPN802 RangeMax™ Wireless Access Point
Start Here
Please refer to the Reference Manual on your
Resource CD
for instructions on advanced
configuration options.
Estimated Completion Time: 30 minutes.
Tip
: Before mounting the WPN802 in a high location, first set up and test the WPN802 to
verify wireless network connectivity.
First, Set Up the WPN802
1. C
ONNECT
THE
WIRELESS
ACCESS
POINT
TO
YOUR
COMPUTER
a.
Unpack the box and verify the contents.
b.
Prepare a computer with Internet access and an Ethernet adapter. If this computer
is already part of your network, record its TCP/IP configuration settings. Config-
ure the computer with a static IP address of 192.168.0.210 and 255.255.255.0 as
the Subnet Mask.
c.
Connect an Ethernet cable from
the WPN802 to the PC.
d.
Securely insert the other end of
the cable into the WPN802
Ethernet port.
e.
Turn on your computer, and connect the power adapter to the WPN802. Then
check the lights on the front:
•
Power
: The power light should be lit. If the power light is not lit,
check the connections and check to see if the power outlet is controlled by a
wall switch that is turned off.
•
Test
: The test light blinks when the WPN802 is first turned on.
•
WLAN:
The wireless light should be lit.
•
Ethernet
: The Ethernet (LAN) light should be lit (amber for a 10
Mbps connection and green for a 100 Mbps connection). If not, make sure
the Ethernet cable is securely attached at both ends.
2. C
ONFIGURE
LAN
AND
W
IRELESS
A
CCESS
a.
Configure the WPN802 Ethernet port for LAN access.
•
Connect to the WPN802 by opening your browser and
entering http://192.168.0.231 in the address field.
•
When prompted, enter
admin
for the user name and
password
for the
password, both in lower case letters.
•
Click the Basic Settings link and configure the IP Settings for your network.
b.
Configure the wireless interface for wireless access. See the online help or the
Reference Manual for full instructions.
c.
Test wireless connectivity using a computer with a wireless adapter configured
according to the wireless settings you just set in the WPN802 to establish a
wireless connection to the WPN802.
Now that you have finished the setup steps, you are ready to deploy the WPN802 in
your network. If needed, you can now reconfigure the PC you used in step 1 back to
its original TCP/IP settings.
Deploy the WPN802
1.
Disconnect the WPN802 from the computer and place it
where you will deploy it.
The best location is elevated, such as wall mounted or on
the top of a cubicle, at the center of your wireless coverage
area, and within line of sight of all the mobile devices. If the
WPN802 is on a metal surface it must be positioned
vertically.
2.
Connect an Ethernet cable from your WPN802 Access
Point to a LAN port on your router, switch, or hub.
3.
Connect the power adapter to the wireless access point and plug the power adapter in
to a power outlet. The Power, WLAN and Ethernet lights should light up.
Now, Verify Wireless Connectivity
Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by
using a browser such as Netscape® or Internet Explorer to connect to the Internet, or
check for file and printer access on your network.
Note
: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference
Manual on the
Resource CD
for the Wireless Access Point.
,QWHUQHW
WPN802
Router
Downloaded from
www.Manualslib.com
manuals search engine
Page 2 / 2
May 2005
Troubleshooting Tips
Here are some tips for correcting simple problems you may have.
No lights are lit on the access point.
The access point has no power.
•
Make sure the power cord is connected to the access point and plugged in to a
working power outlet or power strip.
•
Make sure you are using the correct NETGEAR power adapter supplied with your
access point.
The Ethernet light is not lit.
There is a hardware connection problem.
•
Make sure the cable connectors are securely plugged in at the access point and the
network device (hub, switch, or router).
•
Make sure the connected device is turned on.
The WLAN light is not lit.
The access point’s antennas are not working.
•
If the Wireless LAN activity light stays off, disconnect the adapter from its power
source and then plug it in again.
•
Contact NETGEAR if the WLAN light remains off.
I cannot configure the access point from a browser.
Check these items:
•
The WPN802 is properly installed, LAN connections are OK, and it is powered on.
Check that the LAN port LED is green to verify that the Ethernet connection is OK.
•
If you are using the NetBIOS name of the WPN802 to connect, ensure that your PC
and the WPN802 are on the same network segment or that there is a WINS server on
your network.
•
If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the
range of the WPN802. The WPN802 default IP Address is 192.168.0.231 and the
default Subnet Mask is 255.255.255.0. The WPN802 default setting is for a static IP
address. If the network where you are connecting it is using DHCP, configure it
accordingly. See the Reference Manual on the
Resource CD
for the Wireless Access
Point for more details.
I cannot access the Internet or the LAN with a wireless capable
computer.
There is a configuration problem. Check these items:
•
You may not have restarted the computer with the wireless adapter to have TCP/IP
changes take effect. Restart the computer.
•
The computer with the wireless adapter may not have the correct TCP/IP settings to
communicate with the network. Restart the computer and check that TCP/IP is set up
properly for that network. The usual setting for Windows on the Network Properties
is set to “Obtain an IP address automatically.”
•
The access point’s default values may not work with your network. Check the access
point default configuration against the configuration of other devices in your network.
•
For full instructions on changing the access point’s default values, see the Reference
Manual on the
Resource CD
for the Wireless Access Point.
Technical Support
Thank you for selecting NETGEAR products.
To register your product, go to:
Go to
for support information.
©2005 by NETGEAR, Inc. All rights reserved.
NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand
and product names are trademarks or registered trademarks of their respective holders. Information is subject to
change without notice.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top