1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WNDR3400v2
    5. /
  5. 19
Page 91 / 121 Scroll up to view Page 86 - 90
Advanced Settings
91
N600 Wireless Dual Band Router WNDR3400v2
host name that you configure in the router. Then, whenever your ISP-assigned IP address
changes, your router automatically contacts the Dynamic DNS service provider, logs in to
your account, and registers your new IP address. If your host name is hostname, for
example, you can reach your router at
.
On the Advanced tab, select
Advanced Setup > Dynamic DNS
to display the following
screen:
Figure 5. Forward traffic to a changing IP address
To set up Dynamic DNS:
1.
Register for an account with one of the Dynamic DNS service providers whose names
appear in the Service Provider list. For example, for DynDNS.org, select
www.dyndns.org
.
2.
Select the
Use a Dynamic DNS Service
check box.
3.
Select the name of your Dynamic DNS service provider.
4.
Type the host name (or domain name) that your Dynamic DNS service provider gave you.
5.
Type the user name for your Dynamic DNS account. This is the name that you use to log in
to your account, not your host name.
6.
Type the password (or key) for your Dynamic DNS account.
7.
If your Dynamic DNS provider allows the use of wildcards in resolving your URL, you can
select the
Use Wildcards
check box to activate this feature.
For example, the wildcard feature causes *.yourhost.dyndns.org to be aliased to the
same IP address as yourhost.dyndns.org.
8.
Click
Apply
to save your configuration.
Page 92 / 121
Advanced Settings
92
N600 Wireless Dual Band Router WNDR3400v2
Static Routes
Static routes provide additional routing information to your router. Under usual
circumstances, the router has adequate routing information after it has been configured for
Internet access, and you do not need to configure additional static routes. You have to
configure static routes only for unusual cases such as multiple routers or multiple IP subnets
located on your network.
As an example of when a static route is needed, consider the following case:
•
Your primary Internet access is through a cable modem to an ISP.
•
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is
1
92.168.1.100.
•
Your company’s network address is 134.177.0.0.
When you first configured your router, two implicit static routes were created. A default route
was created with your ISP as the gateway, and a second static route was created to your
local network for all 192.168.1.x addresses. With this configuration, if you attempt to access a
device on the 134.177.0.0 network, your router forwards your request to the ISP. The ISP
forwards your request to the company where you are employed, and the request is likely to
be denied by the company’s firewall.
In this case you have to define a static route, telling your router that 134.177.0.0 should be
accessed through the ISDN router at 192.168.1.100. In this example:
•
The Destination IP Address and IP Subnet Mask fields specify that this static route
applies to all 134.177.x.x addresses.
•
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.1.100.
•
A metric value of 1 will work since the ISDN router is on the LAN.
•
Private is selected only as a precautionary security measure in case RIP is activated.
Page 93 / 121
Advanced Settings
93
N600 Wireless Dual Band Router WNDR3400v2
To set up a static route:
1.
Select
Advanced > Advanced Setup > Static Routes
, and click
Add
to display the
following screen:
2.
In the Route Name field, type a name for this static route (for identification purposes only.)
3.
Select the
Private
check box if you want to limit access to the LAN only. If Private is
selected, the static route is not reported in RIP.
4.
Select the
Active
check box to make this route effective.
5.
Type the IP address of the final destination.
6.
Type the IP subnet mask for this destination. If the destination is a single host, type
255.255.255.255
.
7.
Type the gateway IP address, which has to be a router on the same LAN segment as the
N600 Wireless Dual Band Router.
8.
Type a number between 1 and 15 as the metric value.
This value represents the number of routers between your network and the destination.
Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
9.
Click
Apply
to add the static route.
Page 94 / 121
Advanced Settings
94
N600 Wireless Dual Band Router WNDR3400v2
Remote Management
The remote management feature lets you upgrade or check the status of your N600 Wireless
Dual Band Router over the Internet.
To set up remote management:
1.
Select
Advanced > Advanced Setup > Remote Management
.
Note:
Be sure to change the router’s default login password to a very secure
password. The ideal password should contain no dictionary words from any
language and contain uppercase and lowercase letters, numbers, and
symbols. It can be up to 30 characters.
2.
Select the
Turn Remote Management On
check box.
3.
Under Allow Remote Access By, specify the external IP addresses to be allowed to access
the router’s remote management.
Note:
For enhanced security, restrict access to as few external IP addresses
as practical.
•
To allow access from a single IP address on the Internet, select
Only This Computer
.
Enter the IP address that will be allowed access.
•
To allow access from a range of IP addresses on the Internet, select
IP Address
Range
. Enter a beginning and ending IP address to define the allowed range.
•
To allow access from any IP address on the Internet, select
Everyone
.
4.
Specify the port number for accessing the management interface.
Page 95 / 121
Advanced Settings
95
N600 Wireless Dual Band Router WNDR3400v2
Normal web browser access uses the standard HTTP service port 80. For greater
security, enter a custom port number for the remote web management interface. Choose
a number between 1024 and 65535, but do not use the number of any common service
port. The default is 8080, which is a common alternate for HTTP.
5.
Click
Apply
to have your changes take effect.
6.
When accessing your router from the Internet, type your router’s WAN IP address into your
browser’s address or location field followed by a colon (:) and the custom port number. For
example, if your external address is 134.177.0.123 and you use port number 8080, enter
in your browser.
USB Settings
For added security, the router can be set up to share only approved USB devices. See
Specify Approved USB Devices
on page
56 for the procedure.
Universal Plug and Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
to access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
Note:
If you use applications such as multiplayer gaming, peer-to-peer
connections, or real-time communications such as instant
messaging or remote assistance (a feature in Windows XP), you
should enable UPnP.

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top