RangeMax NEXT Wireless-N Access Point WN802T Reference Manual

6-4

Troubleshooting

v1.0, August 2007

•

Reset to Factory Defaults:

This button can also be used to clear ALL data and restore ALL

settings to the factory default values. These settings are shown in

Appendix A, “Default

Settings and Technical Specifications”

.

To clear all data and restore the factory default values:

1.

Power off the WN802T and power it back on.

2.

Use something with a small point, such as a pen, to press the reset button in and hold it in for

at least five seconds—or until the power light changes from blinking green to amber.

3.

Release the reset button.

The factory default configuration has now been restored, and the WN802T is ready for use.

Default Settings and Technical Specifications

A-1

v1.0, August 2007

Appendix A

Default Settings and Technical Specifications

This appendix provides the factory default settings and technical specifications for the RangeMax

NEXT Wireless-N Access Point.

Factory Default Settings

You can use the reset button located on the front of your device to reset all settings to their factory

defaults. This is called a hard reset.

•

To perform a hard reset, push and hold the reset button for approximately 5 seconds (until the

Power LED changes from blinking green to solid amber). Your device will return to the

factory configuration settings shown in

Table A-1

below.

•

Pressing the reset button for a shorter period of time will simply cause your device to reboot.

Table A-1. Access Point Default Configuration Settings

Feature

Description

AP Login

User Login URL

192.168.0.233 or

netgearxxxxxx”; where xxxxxx is the last 6 hexadecimal

digits of the WN802T MAC address

.

User Name (case sensitive)

admin

Login Password (case sensitive)

password

Ethernet Connection

Access Point Name

netgearxxxxxx where xxxxxx are the last 6 digits of the

wireless access point MAC address.

Ethernet MAC Address

See rear label.

Access Point Mode

On

Port Speed

10/100/1000 Mbps

Local Network (LAN)

RangeMax NEXT Wireless-N Access Point WN802T Reference Manual

A-2

Default Settings and Technical Specifications

v1.0, August 2007

Lan IP

192.168.0.233

Subnet Mask

255.255.255.0

Gateway Address

192.168.0.1

DHCP Client

Disabled

Time Zone

GMT-08:00

Time Zone Adjusted for Daylight Saving

Time

Disabled

Wireless

Operating Mode

11b/g/Next (20/40 MHz)

Wireless Communication

Enabled

Wireless Network Name (SSID)

NETGEAR

Broadcast Network Name SSID

Enabled

Security

Disabled

Transmission Speed

Auto

a

Country/Region

United States (in North America; otherwise, varies by

region)

Channel/Radio Frequency

6/2.43 GHz (until the region is selected)

Output Power

Full

Wireless Card Access List

All wireless stations allowed

a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary.

Network conditions and environmental factors, including volume of network traffic, building materials and

construction, and network overhead, lower actual data throughput rate.

Table A-1. Access Point Default Configuration Settings

Feature

Description

RangeMax NEXT Wireless-N Access Point WN802T Reference Manual

Default Settings and Technical Specifications

A-3

v1.0, August 2007

Technical Specifications

Table A-2. WN802T Technical Specifications

Parameter

RangeMax NEXT Wireless-N Access Point

802.11Next Data Rates

7.2, 14.4, 21.7, 28.9,43.3, 57.8, 65, 72.2, 87.7, 115.6, 130 & 144.4 Mbps (20Hz)

15, 30, 45, 60, 90, 120. 135. 150, 180, 240, 270 & 300 Mbps (40Hz)

802.11b/g Data Rates

1, 2, 5.5, 11, 12, 18, 24, 36, 38, 54, & 108 Mbps (Auto-rate capable)

802.11b/g/Next

Operating Frequencies

2.412 ~ 2.462 GHz (US)

2.457 ~ 2.462 GHz (Spain)

2.412 ~ 2.484 GHz (Japan)

2.457 ~ 2.472 GHz (France)

2.412 ~ 2.472 GHz (Europe ETSI)

802.11b/g/Next

Encryption

40-bits (also called 64-bits), 128-bits WEP data encryption; TKIP (WPA-PSK)

and AES (WPA2-PSK)

Network Management

Web-based configuration and status monitoring

Maximum Clients

Limited by the amount of wireless network traffic generated by each node;

typically 15 to 20 nodes.

Status LEDs

Power/Ethernet LAN/Wireless LAN

Power Adapter

12V DC, 1.5 A Switching Power Supply

Electromagnetic

Compliance

FCC Part 15 Class B and Class E, CE, and C-TICK

Environmental

Specifications

Operating temperature: 0 to 50° C

Operating humidity: 5-95%, non-condensing

RangeMax NEXT Wireless-N Access Point WN802T Reference Manual

A-4

Default Settings and Technical Specifications

v1.0, August 2007