Page 16 / 169 Scroll up to view Page 11 - 15
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
2-4
Introduction
202-10042-02 v1.1
Connectors, Reset Buttons, Ports, and Label Information
Each unit has various status indicators, a reset button, and a label with important information.
Familiarize yourself with these features of your product.
The WGX102 Wireless Unit
The front panel of the WGX102 contains the status lights described below.
Figure 2-1:
WGX102 Front Panel
Table 2-1.
Status Light Descriptions
Label
Activity
Description
Power
On Green Solid
Blink
Off
Power is supplied to the WGX102.
Power on self test.
Power is not supplied to the WGX102.
HomePlug — AP Mode
Internet — Router Mode
On
Off
The HomePlug port (or Internet port in Router Mode) has
detected a link with an attached device.
No devices are attached on the Powerline network.
Wireless
On
Blink
Off
The Wireless port is initialized and the wireless feature is
enabled.
Data is being transmitted or received by the wireless port.
There is a problem with the device. See
Chapter 8,
“Troubleshooting”
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Introduction
2-5
202-10042-02 v1.1
The Label on the Rear Panel of the WGX102
The label on the rear panel of the WGX102 contains the items listed below.
MAC address
Model number
Serial number
Unique device Passcode (PWD)
The WGX102 Bottom Panel
The factory default reset push button is located on the bottom panel of the WGX102, as shown
below.
Figure 2-2:
WGX102 Underside
Use a fine pen point or an unfolded paper clip to push in the reset button. If you press the reset
button for less than 15 seconds, the WGX102 does a soft reset, similar to unplugging and then
plugging the device in again.
When you press the reset button for 15 seconds or more, the WGX102 resets to the factory
defaults, as described in
“Restoring the Default WGX102 Configuration and Password” on
page 8-7
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
2-6
Introduction
202-10042-02 v1.1
The XE102 Wall-Plugged Ethernet Bridge
he front panel of the XE102 contains the status lights described below.
Figure 2-3:
XE102 Front Panel
You can use the status lights to verify connections. Viewed from top to bottom, the table below
describes the lights on the front panel.
Table 2-1.
Status Light Descriptions
Label
Activity
Description
Power
On Green Solid
Blink
Off
Power is supplied to the XE102.
Power on self test.
Power is not supplied to the XE102.
HomePlug
On
Off
The HomePlug port has detected a link with an attached
device.
No devices are attached on the Powerline network.
Ethernet
On
Blink
Off
The Ethernet port has an Ethernet cable connected to a
powered on device such as a switch, router, or computer.
Data is being transmitted or received by the wireless port.
There is no active Ethernet connection.
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Introduction
2-7
202-10042-02 v1.1
The Label on the Rear Panel of the XE102
The label on the rear panel of the WGX102 contains the items listed below.
MAC address
Model number
Serial number
Unique device Passcode (PWD)
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
2-8
Introduction
202-10042-02 v1.1
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top