Page 81 / 169 Scroll up to view Page 76 - 80
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Advanced Configuration of the WGX102
7-13
202-10042-02 v1.1
Figure 7-10:
PPPoE menu
If you know that your ISP does not automatically transmit DNS addresses to the wireless
range extender during login, select “Use these DNS servers” and enter the IP address of your
ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it also.
Note:
If you enter DNS addresses, restart your computers so that these settings take effect.
Click
Apply
to save your settings.
Click Test to verify that your Internet connection works. If the NETGEAR Web site does not
appear within one minute, refer to
Chapter 8, “Troubleshooting”
.
Manual PPTP Configuration
If your ISP uses PPTP, select PPTP for the Internet Service Provider and you will see the following
menu:
Downloaded from
www.Manualslib.com
manuals search engine
Page 82 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
7-14
Advanced Configuration of the WGX102
202-10042-02 v1.1
Figure 7-11:
PPTP menu
Enter your Login and Password. These fields are case sensitive.
To change the login timeout, enter a new value in minutes. This determines how long the
wireless range extender keeps the Internet connection active after there is no Internet activity
from the LAN. Entering a timeout value of zero means never log out.
Note:
You no longer need to run the ISP’s login program on your PC in order to access the
Internet. When you start an Internet application, your wireless range extender automatically
logs you in.The Domain Name Server (DNS) Address parameters may be necessary to access
your ISP’s services such as mail or news servers.
Downloaded from
www.Manualslib.com
manuals search engine
Page 83 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Advanced Configuration of the WGX102
7-15
202-10042-02 v1.1
Enter your IP address if your ISP provided a fixed IP address, such as 10.0.1.20. Otherwise,
leave the IP address set to 0.0.0.0 and you will be automatically assigned an IP address when
you connect.
Enter a Server IP Address is your ISP provided one, such as 10.0.0.138. Otherwise, leave the
IP address set to 0.0.0.0 and the Server IP Address will be automatically supplied when you
connect.
Normally the Connection ID/Name should be left blank. If your ISP provided one, then enter it
here.
If you know that your ISP does not automatically transmit DNS addresses to the wireless
range extender during login, select “Use these DNS servers” and enter the IP address of your
ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it also.
Note:
If you enter DNS addresses, restart your computers so that these settings take effect.
The Router MAC Address section determines the Ethernet MAC address that will be used by
the wireless range extender on the Internet port. Some ISPs register the Ethernet MAC address
of the network interface card in your PC when your account is first opened. They will then
only accept traffic from the MAC address of that PC. This feature allows your wireless range
extender to masquerade as that PC.
To change the MAC address, select “Use this Computer’s MAC address.” The wireless range
extender then captures and uses the MAC address of the PC that you are now using. You must
be using the one PC that is allowed by the ISP. Or, select “Use this MAC address” and enter it.
Click
Apply
to save your settings.
Click Test to test your Internet connection. If the NETGEAR Web site does not appear within
one minute, refer to
Chapter 8, “Troubleshooting”
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 84 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
7-16
Advanced Configuration of the WGX102
202-10042-02 v1.1
Configuring the WGX102 in Router Mode
The figure below shows the menu choices available when the WGX102 is in Router Mode.
Figure 7-12:
Router Mode menu
Downloaded from
www.Manualslib.com
manuals search engine
Page 85 / 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Advanced Configuration of the WGX102
7-17
202-10042-02 v1.1
Router Mode Port Triggering
Port Triggering is an advanced feature that can be used to easily enable gaming and other internet
applications. Port Forwarding is typically used to enable similar functionality, but it is static and
has some limitations.
Note:
If you use applications such as multi-player gaming, peer-to-peer connections, real time
communications such as instant messaging, or remote assistance (a feature in Windows XP), you
should also enable UPnP according to the instructions at
“Router Mode Universal Plug and Play
(UPnP)” on page 7-33
.
Port Triggering opens an incoming port temporarily and does not require the server on the Internet
to track your IP address if it is changed by DHCP, for example. Port Triggering monitors outbound
traffic. When the wireless range extender detects traffic on the specified outbound port, it
remembers the IP address of the computer that sent the data and triggers the incoming port.
Incoming traffic on the triggered port is then forwarded to the triggering computer.
Using the Port Triggering page, you can make local computers or servers available to the Internet
for different services (for example, FTP or HTTP), to play Internet games (like Quake III), or to
use Internet applications (like CUseeMe).
Port Forwarding is designed for FTP, Web Server or other server based services. Once port
forwarding is set up, requests from the Internet are forwarded to the proper server. On the contrary,
port triggering only allows request from Internet after a designated port is 'triggered'. Port
triggering applies to chat and Internet games.
Figure 7-13:
Port Triggering menu
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top