1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGU624
    5. /
  5. 26
Page 126 / 178 Scroll up to view Page 121 - 125
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
C-4
Preparing Your Network
M-10153-01
If you need Client for Microsoft Networks:
a.
Click the Add button.
b.
Select Client, and then click Add.
c.
Select Microsoft.
d.
Select Client for Microsoft Networks, and then click OK.
3.
Restart your PC for the changes to take effect.
Enabling DHCP to Automatically Configure TCP/IP Settings
After the TCP/IP protocol components are installed, each PC must be assigned specific
information about itself and resources that are available on its network. The simplest way to
configure this information is to allow the PC to obtain the information from a DHCP server in the
network.
You will find there are many similarities in the procedures for different Windows systems
when using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these
versions of Windows.
Locate your Network Neighborhood icon.
•
If the Network Neighborhood icon is on the Windows desktop, position your mouse
pointer over it and right-click your mouse button.
•
If the icon is not on the desktop,
•
Click Start on the task bar located at the bottom left of the window.
•
Choose Settings, and then Control Panel.
•
Locate the Network Neighborhood icon and click on it. This will open the Network
panel as shown below.
Page 127 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
Preparing Your Network
C-5
M-10153-01
Verify the following settings as shown:
•
Client for Microsoft Network exists
•
Ethernet adapter is present
•
TCP/IP is present
•
Primary Network Logon is set to
Windows logon
Click the Properties
button. The following
TCP/IP Properties window will display.
Page 128 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
C-6
Preparing Your Network
M-10153-01
Selecting Windows’ Internet Access Method
1.
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2.
Double-click the Internet Options icon.
3.
Select “I want to set up my Internet connection manually” or “I want to connect through a
Local Area Network” and click Next.
4.
Select “I want to connect through a Local Area Network” and click Next.
5.
Uncheck all boxes in the LAN Internet Configuration screen and click Next.
6.
Proceed to the end of the Wizard.
Verifying TCP/IP Properties
After your PC is configured and has rebooted, you can check the TCP/IP configuration using the
utility
winipcfg.exe
:
1.
On the Windows taskbar, click the Start button, and then click Run.
•
By default, the IP Address
tab is open on this
window.
• Verify the following:
Obtain an IP address automatically
is
selected. If not selected, click in the radio
button to the left of it to select it.
This
setting is required to enable the DHCP server
to automatically assign an IP address.
• Click OK to continue.
Restart the PC.
Repeat these steps for each PC with this
version of Windows on your network.
Page 129 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
Preparing Your Network
C-7
M-10153-01
2.
Type
winipcfg
, and then click OK.
The IP Configuration window opens, which lists (among other things), your IP address, subnet
mask, and default gateway.
3.
From the drop-down box, select your Ethernet adapter.
The window is updated to show your settings, which should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
•
The IP address is between 192.168.1.2 and 192.168.1.254
•
The subnet mask is 255.255.255.0
•
The default gateway is 192.168.1.1
Configuring Windows NT4, 2000 or XP for IP Networking
As part of the PC preparation process, you may need to install and configure
TCP/IP on each networked PC. Before starting, locate your Windows CD; you may need to insert
it during the TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
1.
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2.
Double-click the Network and Dialup Connections icon.
3.
If an Ethernet adapter is present in your PC, you should see an entry for Local Area
Connection. Double-click that entry.
4.
Select Properties.
5.
Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6.
Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7.
Click OK and close all Network and Dialup Connections windows.
8.
Then, restart your PC.
Page 130 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
C-8
Preparing Your Network
M-10153-01
DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4
You will find there are many similarities in the procedures for different Windows systems when
using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these versions of
Windows.
DHCP Configuration of TCP/IP in Windows XP
Locate your Network Neighborhood icon.
•
Select Control Panel from the Windows XP new Start Menu.
•
Select the Network Connections icon on the Control Panel.
This will take you to the next
step.
• Now the Network Connection window
displays.
The Connections List that shows all the
network connections set up on the PC,
located to the right of the window.
• Right-click on the Connection
you will
use and choose Status.

Rate

4.3 / 5 based on 3 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top