Page 86 / 96
Scroll up to view Page 81 - 85
108 Mbps Wireless Router WGT624 v4 Reference Manual
6-8
Troubleshooting
v1.0, May 2007
Page 87 / 96
Technical Specifications and Default Configuration
A-1
v1.0, May 2007
Appendix A
Technical Specifications and Default
Configuration
This appendix provides technical specifications for the WGT624 v4 wireless router.
Technical Specifications
The table below shows the technical specifications for the WGT624 v4 108 Mbps Wireless Router.
Network Protocol and Standards Compatibility
Data and Routing Protocols:
TCP/IP, RIP-1, RIP-2, DHCP
PPP over Ethernet (PPPoE)
Power Adapter
North America:
120V, 60 Hz, input
United Kingdom, Australia:
240V, 50 Hz, input
Europe:
230V, 50 Hz, input
Japan:
100V, 50/60 Hz, input
All regions (output):
12V DC @ 1 A output, 22W maximum
Physical Specifications
Dimensions:
28 x 175 x 118 mm
(1.1 x 6.89 x 4.65 in.)
Weight:
0.3 kg
(0.66 lb)
Environmental Specifications
Operating temperature:
0
°
to 40
°
C
(32º to 104º F)
Operating humidity:
90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Meets requirements of:
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
Page 88 / 96
108 Mbps Wireless Router WGT624 v4 Reference Manual
A-2
Technical Specifications and Default Configuration
v1.0, May 2007
Interface Specifications
LAN:
10BASE-T or 100BASE-TX, RJ-45
WAN:
10BASE-T or 100BASE-TX, RJ-45
Wireless
Radio Data Rates
1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps
Auto Rate Sensing
Frequency
2.4-2.5 GHz
Data Encoding:
Direct Sequence Spread Spectrum (DSSS)
Maximum Computers Per Wireless
Network:
Limited by the amount of wireless network traffic generated by each
node. Typically 30-70 nodes.
Operating Frequency Ranges:
2.412~2.462 GHz (US)
2.412~2.472 GHz (Japan)
2.412~2.472 GHz (Europe ETSI)
Encryption:
40-bit (also called 64-bit), 128-bit WEP data encryption,
WPA-PSK(TKIP), and WPA2-PSK(AES)
Page 89 / 96
108 Mbps Wireless Router WGT624 v4 Reference Manual
Technical Specifications and Default Configuration
A-3
v1.0, May 2007
Default Configuration Settings
You can use the reset button located on the back of your WGT624 v4 wireless router to reset all
settings to their factory defaults. This is called a hard reset. To perform a hard reset, push and hold
the reset button for 3 seconds. Your wireless router will return to the factory configuration settings
shown in the table below.
Table A-1.
Default Configuration Settings
Feature
Default Behavior
Smart Wizard
Disabled
Router Login
Router Login URL
http://www. routerlogin.net
or
http://www
.
routerlogin.com
Login Name (case sensitive)
admin
Login Password (case sensitive)
password
Internet Connection
WAN MAC Address
Use default hardware address
MTU Size
1500
Local Network
Router LAN IP address (aka Gateway IP
address)
192.168.1.1
Router Subnet
255.255.255.0
DHCP Server
Enabled
Time Zone
GMT
Time Zone Adjusted for Daylight Savings
Time
Disabled
Firewall
Inbound (communications coming in from
the Internet)
Disabled (bars all unsolicited requests except for traffic
on port 80, the http port)
Outbound (communications going out to
the Internet)
Enabled (all)
Page 90 / 96
108 Mbps Wireless Router WGT624 v4 Reference Manual
A-4
Technical Specifications and Default Configuration
v1.0, May 2007
Wireless
Wireless Communication
Enabled
SSID Name
NETGEAR
Security
Disabled
Broadcast SSID
Enabled
Transmission Speed
Auto
*
Country/Region
United States (in North America, otherwise varies by
region)
RF Channel
11 i
n North America, otherwise varies by region
Operating Mode
Auto 108 Mbps in North America & Europe,
otherwise varies by region
Data Rate
Best
Output Power
Full
*. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will
vary. Network conditions and environmental factors, including volume of network traffic, building
materials and construction, and network overhead, lower actual data throughput rate.
Table A-1.
Default Configuration Settings
(continued)
Feature
Default Behavior
19216811.live