1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGR614v10
    5. /
  5. 7
Page 31 / 41 Scroll up to view Page 26 - 30
Troubleshooting
27
To restore your firmware:
a.
Make sure your computer is connected to your router and the router is powered on.
b.
Insert the
Resource CD
that came with your router into your computer.
–
The CD will automatically start and detect the language you are using on your
computer. Select a different language option, if you prefer.
–
If the CD does not automatically start, browse the CD and double-click on
.
c.
In the CD’s menu, click
Supporting Software
, then click
Netgear Firmware Recovery
Utility
, and follow the prompts for the recovery process.
Installation of the utility places a NETGEAR Router Recovery
shortcut on the
desktop.
d.
After firmware recovery is complete, follow the prompts to restore your configuration
settings.
•
Power Light Stays Amber
. When the router is turned on, the Power light turns amber for
about 1 minute and then turns green. If the light does not turn green, the router has a problem.
If the Power light is still amber 2 minutes after turning on power to the router:
a.
Turn the power off and back on to see if the router recovers.
b.
Clear the router’s configuration to factory defaults. This procedure is explained in
“Restoring the Default Password and Configuration Settings” on page 35
.
If the error persists, you might have a hardware problem and should contact technical support.
•
Internet Light Stays Amber
. When the router is turned on, the Internet light turns amber for
about 1 minute and then turns green. If the light does not turn green, the router has a problem.
If the Internet light is still amber 2 minutes after turning on power to the router:
a.
The Internet is not accessible. Confirm that you have the correct internet setting.
b.
Clear the router’s configuration to factory defaults, and then configure the router again.
This procedure is explained in
“Restoring the Default Password and Configuration
Settings” on page 35
.
c.
Turn the power off and back on to see if the router recovers.
•
Internet or LAN Port Lights Not On.
If either the LAN or Internet lights do not light when
the Ethernet connection is made, check the following:
a.
Make sure that the Ethernet cable connections are secure at the router and at the computer.
b.
Make sure that power is turned on to the connected computer.
Page 32 / 41
Troubleshooting
28
c.
Be sure you are using Ethernet cables like the cable that was supplied with the wireless
router.
See
“Connecting Your Wireless Router” on page 12
for instructions.
For more information on WPS functionality and advanced features, see the online
User Manual.
Troubleshooting Login Problems
If you are unable to log in to the wireless router, check the following:
•
If you are using an Ethernet-connected computer, check the Ethernet connection between the
computer and the router as described in
“Checking Basic Router Functions” on page 26
.
•
Make sure you are using the correct login information. The factory default login name is
admin
and the password is
password
. Make sure that the Caps Lock is off when entering this
information.
•
Make sure your computer’s IP address is on the same subnet as the router. If your are using the
recommended addressing scheme, your computer’s address should be in the range of
192.168.1.2 to 192.168.1.254. Refer to your computer’s documentation or see
“Preparing a
Computer for Network Access”
in
“Related Documents” on page 36
for help with configuring
your computer.
•
If your router’s IP address has been changed and you don’t know the current IP address, reset
the router’s configuration to the factory defaults. This procedure is explained in
“Restoring the
Default Password and Configuration Settings” on page 35
.
•
Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet
Explorer, click Refresh to be sure the Java applet is loaded. Try closing the browser and
reopening it again.
•
If you are attempting to set up your NETGEAR router as an additional router behind an
existing router in your network, consider replacing the existing router instead. NETGEAR
does not support such a configuration.
If your computer cannot reach a DHCP server, some operating systems will
assign an IP address in the range 169.254.x.x. If your IP address is in this range,
verify that you have a good connection from the computer to the router, then
restart (reboot) your computer.
Page 33 / 41
Troubleshooting
29
•
If you are attempting to set up your NETGEAR router as a replacement for an ADSL gateway
in your network, the router cannot perform many gateway services, for example, converting
ADSL or Cable data into Ethernet networking information. NETGEAR does not support such
a configuration.
Checking the Internet Service Connection
If your router is unable to access the Internet, check the Internet connection, and then check the
wireless router.
•
Internet Connection
. The cable or DSL modem status lights indicate if the modem
connection is successful or not. Check your modem documentation or call your Internet
service provider for help with verifying that the modem has a successful connection.
•
Wireless Router Internet Light is Green or Blinking Green
. If your Internet light is green
or blinking green, then you have a good Internet connection and your wiring is correct.
•
Wireless Router Internet Light Off
. If the Internet light is off, verify that the Ethernet cable
is securely connected between the cable or DSL modem, and that both the modem and
wireless router are turned on.
Obtaining an Internet IP Address
If your wireless router is unable to access the Internet, and your Internet light is amber, check the
wireless router to see if it is able to get an Internet IP address from your service provider. Unless
you have a static IP address, your wireless router automatically requests an IP address from your
service provider.
To check the Internet IP address from the browser interface:
1.
Log in to the wireless router.
2.
Select the
Router Status
link under the
Maintenance
heading to check that an IP address is
shown for the Internet Port. If 0.0.0.0 is shown, your wireless router has not obtained an IP
address from your service provider.
If your router is unable to obtain an IP address from the your service provider, the problem might
be one of the following:
Page 34 / 41
Troubleshooting
30
•
Your service provider might require a login. Ask your service provider whether they require a
PPP over Ethernet (PPPoE) login.
•
You might have incorrectly set the service name, user name or password. See
“Troubleshooting PPPoE” on page 30
.
•
Your service provider might check for your computer's host name. Assign the computer Host
Name of your ISP account to the wireless router on the
Basic Settings
screen.
•
Your service provider might only allow one Ethernet MAC address to connect to the Internet,
and check for your computer’s MAC address. If this is the case:
–
Inform your service provider that you have bought a new network device, and ask them to
use the wireless router’s MAC address, or
–
Configure your router to spoof your computer’s MAC address. On the
Basic Settings
screen in the Router MAC Address section, select “Use this Computer’s MAC Address”
and click
Apply.
Then restart your network in the correct sequence (see
“Basic Setup
Checklist” on page 25
).
Troubleshooting PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
1.
Log in to the wireless router.
2.
Select
Router Status
under
Maintenance
on the main menu.
3.
Click
Connection Status
. If all of the steps indicate “OK,” then your PPPoE connection is up
and working.
If any of the steps indicate “Failed,” you can attempt to reconnect by clicking
Connect.
The
wireless router will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There also might be a provisioning problem with your ISP.
Unless you connect manually, the wireless router will not authenticate using
PPPoE until data is transmitted to the network.
Page 35 / 41
Troubleshooting
31
Troubleshooting Internet Browsing
If your wireless router can obtain an IP address but your computer is unable to load any web pages
from the Internet, check the following:
•
Your computer might not recognize any DNS server addresses
. A DNS server is a host on
the Internet that translates Internet names (such as www addresses) to numeric IP addresses.
Typically, your ISP will provide the addresses of one or two DNS servers for your use. If you
entered a DNS address during the wireless router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as explained in
the documentation for your computer
.
•
Your computer might not have the wireless router configured as its default gateway
.
Reboot the computer and verify that you can access the router’s GUI through
.
Using the Ping Utility to Troubleshoot
Most computers and routers have a diagnostic utility called
ping
that sends a request to a target
device. The device then replies. The ping utility makes it easy to troubleshoot a network.
Testing the Path from Your Computer to Your Router
You can ping the wireless router to verify that the LAN path from your computer to your router is
set up correctly.
To ping the wireless router from a Windows PC:
1.
From the Windows task bar, click
Start
and select
Run
.
2.
In the field provided, type
ping
followed by the address of the router, as in this example:
ping www.routerlogin.net
3.
Click
OK
. You should see a message like this one:
Pinging www.routerlogin.net with 32 bytes of data
If the path is working, you see this message:
Reply from www.routerlogin.net: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out

Rate

3.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top