1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WG302v2
    5. /
  5. 9
Page 41 / 102 Scroll up to view Page 36 - 40
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
Basic Installation and Configuration
2-19
v1.0, May 2006
SSID and Wireless Security Settings Form
For a new wireless network, print or copy this form and fill in the settings. For an existing wireless
network, the person who set up or is responsible for the network can provide this information. Be
sure to set the Regulatory Domain correctly as the first step. Store this information in a safe place.
•
SSID
:
The Service Set Identification (SSID) identifies the wireless local area network. You
may customize it by using up to 32 alphanumeric characters. Write your SSID on the line.
SSID: ___________________________________
Note:
The SSID in the wireless access point is the SSID you configure in the wireless adapter
card. All wireless nodes in the same network must be configured with the same SSID.
•
Authentication
Circle one: Open System or Shared Key. Choose “Shared Key” for more security.
Note:
If you select shared key, the other devices in the network will not connect unless they
are set to Shared Key and have the same keys in the same positions as those in the WG302v2.
•
WEP Encryption Keys
For all four data encryption keys, choose the Key Size. Circle one: 64, 128, or 152 bits
Key 1: ___________________________________
Key 2: ___________________________________
Key 3: ___________________________________
Key 4: ___________________________________
•
WPA-PSK (Pre-Shared Key)WPA2-PSK (Pre-Shared Key)
Record the WPA-PSK key:Record the WPA2-PSK key:
Key: ________________________________
Key: _______________________________
•
WPA RADIUS Settings
For WPA, record the following settings for the primary and secondary RADIUS servers:
Server Name/IP Address: Primary _________________
Secondary __________________
Port: ___________________________________
Shared Secret: ___________________________________
•
WPA2 RADIUS Settings
For WPA2, record the following settings for the primary and secondary RADIUS servers:
Server Name/IP Address: Primary _________________
Secondary __________________
Port: ___________________________________
Shared Secret: ___________________________________
Page 42 / 102
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
2-20
Basic Installation and Configuration
v1.0, May 2006
Configuring the RADIUS Server Settings
To view or change the RADIUS Server Settings:
1.
Connect to the WG302v2.
2.
In the address field of your Web browser, enter the default LAN address of
.
Log in with the user name of
admin
and default password of
password
,
or log in by using the LAN address and password that you configured.
3.
In the Security menu, click RADIUS Server Settings.
4.
Enter the settings for the primary RADIUS server and secondary RADIUS server (if
available).
5.
Click
Apply
to save your settings.
Figure 2-8
Page 43 / 102
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
Basic Installation and Configuration
2-21
v1.0, May 2006
The following list describes the RADIUS Server Settings:
•
Authentication Server Configuration.
This configuration is required for authentication and
access control using a RADIUS Server.The IP Address, Port Number and Shared Secret are
required for communication with the RADIUS Server. You can configure a Secondary
RADIUS Server to use if the Primary RADIUS Server fails.
•
IP Address.
The IP address of the RADIUS Server. The default is 0.0.0.0.
•
Port Number.
The port number of the RADIUS Server. The default is 1812.
•
Shared Secret.
This is shared between the Wireless Access Point and the RADIUS Server
while authenticating the supplicant (wireless client). The shared secret can contain up to 63
standard alphanumeric and special characters. The shared secret is case sensitive.
•
Accounting Server Configuration.
This configuration is required for accounting using a
RADIUS Server. The IP Address, Port Number and Shared Secret are required for
communication with the RADIUS Server. You can configure a Secondary RADIUS Server to
use if the Primary RADIUS Server fails.
•
IP Address.
The IP address of the RADIUS Server. The default is 0.0.0.0.
•
Port Number.
Port number of the RADIUS Server. The default is 1813.
•
Shared Secret.
This is shared between the Wireless Access Point and the RADIUS Server
while authenticating the supplicant.
Restricting Wireless Access by MAC Address
To restrict access based on MAC addresses, use the following steps:
1.
Connect to the WG302v2 by entering the IP address of the WG302v2 into the address field of
your Web browser.
2.
From the Security menu, click the Access Control link to display the Access Control menu
shown in
Figure 2-9
.
Page 44 / 102
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
2-22
Basic Installation and Configuration
v1.0, May 2006
3.
Select the Turn Access Control On check box.
4.
Either select from the list of available wireless stations the WG302v2 has found in your area,
or enter the MAC address for a device you plan to use.
You can usually find the MAC address of a wireless station printed on the wireless adapter.
Click Add to add the wireless device to the access list. Repeat these steps for each additional
device you want to add to the list.
5.
Be sure to click
Apply
to save your wireless access control list settings.
Now, only devices on the MAC ACL will be allowed to wirelessly connect to the WG302v2.
Figure 2-9
Note:
When configuring the WG302v2 from a wireless computer whose MAC
address is not in the access control list, if you select Turn Access Control On,
you will lose your wireless connection when you click Apply. You must then
access the wireless access point from a wired computer or from a wireless
computer which is on the access control list to make any further changes.
Page 45 / 102
Management and Information
3-1
v1.0, May 2006
Chapter 3
Management and Information
This chapter describes how to use the management and information features of your ProSafe
802.11g Wireless Access Point. To get to these features, connect to the WG302v2 as described in
“Logging in to the WG302v2 Using Its Default IP Address” on page 2-7
.
Changing the Administrator Password
The default password is
password
. NETGEAR recommends that you change this password to a
more secure password. You cannot change the administrator login name.
To change the default password:
1.
From the WG302v2 main menu, click Change Password to go to the menu shown
below.
Figure 3-1
2.
Change the password by first entering the old password, and then enter the new password
twice.
3.
Click
Apply
to save your change.
Figure 3-1

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top