Page 76 / 102
Scroll up to view Page 71 - 75
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
5-4
Troubleshooting
v1.0, May 2006
I am unable to download files from some FTP sites.
If the IP address of the WG302v2 LAN interface is not on the same network as the IP addresses
the DHCP server on the WG302v2 assigns to wireless clients, the WG302v2 performs automatic
network address and port translation (NAPT). Some higher-layer protocols, such as FTP, might not
work with the NAPT on the WG302v2.
To fix this issue, reconfigure the DHCP server settings (Advanced IP Settings) so that the wireless
clients receive IP addresses that are on the same network as the WG302v2 Ethernet interface.
I need to restore factory default settings
.
To restore the factory default settings, you can use the Reset button (see
“Using the Reset Button
to Restore Factory Default Settings” on page 3-6
) or use the Backup/Restore Settings menu (see
“Erasing the Configuration” on page 3-6
). To view a list of the factory default settings, see
“Default Factory Settings” on page B-1
.
Page 77 / 102
Related Documents
A-1
v1.0, May 2006
Appendix A
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
Internet Networking and TCP/IP
Addressing:
Wireless Communications:
Preparing a Computer for
Network Access:
Virtual Private Networking
(VPN):
Glossary:
Page 78 / 102
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
A-2
Related Documents
v1.0, May 2006
Page 79 / 102
Specifications
B-1
v1.0, May 2006
Appendix B
Specifications
This appendix provides default factory settings and technical specifications for the ProSafe
802.11g Wireless Access Point.
Default Factory Settings
You can use the reset button located on the rear panel of your device to reset all settings to their
factory defaults. This is called a hard reset. To perform a hard reset, push and hold the reset button
for three seconds. Your device will return to the factory configuration settings shown in
Table B-1
.
Table B-1
Access Point Default Configuration Settings
Feature
Description
AP Login
User Login URL
192.168.0.228
User Name (case sensitive)
admin
Login Password (case sensitive)
password
Ethernet Connection
Ethernet MAC Address
See bottom label.
Port Speed
10/100
Basic Settings
AP Name
netgearxxxxxx, where xxxxxx are the last six digits of the
wireless access point's MAC address
Country / Region
United States (in North America; otherwise, varies by
region)
IP Address
192.168.0.228
Subnet Mask
255.255.255.0
DHCP Client
Disabled
Spanning Tree Protocol
Enabled
VLAN (802.1Q)
Enabled
Page 80 / 102
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
B-2
Specifications
v1.0, May 2006
Untagged Packet and VLAN Mapping
Disabled
Untagged VLAN ID
1
Time Zone
GMT
Time Zone Adjusted for Daylight Saving
Time
Disabled
Wireless Settings
Wireless Communication (Radio)
Enabled
802.11g Network Name (SSID)
NETGEAR
Broadcast SSID
Enabled
802.11g Radio Frequency Channel
Channel 11
Data Rate
Auto
*
Output Power
Full
Security Profile Settings
Profile Name
NETGEAR
SSID
NETGEAR
Security
Open System
VLAN ID
1
Status
Enabled (all other security profiles are disabled)
Radius Server Settings
Authentication Server IP Address
0.0.0.0
Authentication Server Port
1812
Accounting Server IP Address
0.0.0.0
Accounting Server Port
1813
Table B-1
Access Point Default Configuration Settings
Feature
Description
19216811.live