1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WG102
    5. /
  5. 11
Page 51 / 118 Scroll up to view Page 46 - 50
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG102
Basic Installation and Configuration
3-29
202-10064-02, June 2005
2.
Click
WEP/WPA Settings
in the Security menu of the WG102.
Figure 3-17:
WEP/WPA Settings menu
3.
Choose
WPA2-PSK
from the list.
4.
Enter the pre-shared key passphrase.
5.
Click
Apply
to save your settings.
How to Configure WPA and WPA2
Note
: Not all wireless adapters support WPA. Furthermore, client software is required on the
client. Windows XP and Windows 2000 with Service Pack 3 do include the client software that
supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA.
Consult the product document for your wireless adapter and WPA client software for instructions
on configuring WPA settings.
Note
: Not all wireless adapters support WPA2. Furthermore, client software is required on the
client. Make sure your client card supports WPA2. Consult the product document for your wireless
adapter and WPA2 client software for instructions on configuring WPA2 settings.
Page 52 / 118
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG102
3-30
Basic Installation and Configuration
202-10064-02, June 2005
To configure WPA and WPA2, follow these steps:
1.
Log in at the default LAN address of
with the default user name of
admin
and default password of
password
, or using whatever LAN address and password you
have set up.
2.
Click
Radius Server Settings
in the Security menu.
Figure 3-18:
Radius Server Settings menu
3.
Enter the Radius settings.
•
Authentication/Access Control Radius Server Configuration
: This configuration is
required for authentication using Radius. IP Address, Port No. and Shared Secret is
required for communication with Radius Server. A Secondary Radius Server can be
configured which is used on failure on Primary Radius Server
•
IP Address
: The IP address of the Radius Server. The default is 0.0.0.0.
•
Port Number
: Port number of the Radius Server. The default is 1812.
Page 53 / 118
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG102
Basic Installation and Configuration
3-31
202-10064-02, June 2005
•
Shared Secret
: This is shared between the Wireless Access Point and the Radius Server
while authenticating the supplicant.
•
Re-authentication Time
: The time interval in seconds after which the supplicant will be
authenticated again with the Radius Server. The default is 3600 seconds.
•
Global-key Re-Key Time
: Check on this option to enable Re-keying of Global Key. The
Global Key Re-Key can be done based on time interval in seconds or number of packets
exchanged using the global key. The default is 3600 seconds.
•
Update if any station disassociates
: Check on this option to refresh global key when any
stations disassociated with wireless Access Point.
•
Accounting Radius Server Configuration
: This configuration is required for accounting
using Radius Server. IP Address, Port No. and Shared Secret is required for
communication with Radius Server. A Secondary Radius Server can be configured which
is used on failure on Primary Radius Server.
•
IP Address
: The IP address of the Radius Server. The default is 0.0.0.0.
•
Port Number
: Port number of the Radius Server. The default is 1813.
•
Shared Secret
: This is shared between the Wireless Access Point and the Radius Server
while authenticating the supplicant.
4.
Click
Apply
to save your settings.
5.
Click
WEP/WPA Settings
in the Security menu.
Figure 3-19:
WEP/WPA Settings menu
Page 54 / 118
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG102
3-32
Basic Installation and Configuration
202-10064-02, June 2005
6.
Choose
WAP and WPA2 with Radius
from the list.
7.
Click
Apply
to save your settings.
How to Configure WPA2-PSK and WPA2-PSK
Note
: Not all wireless adapters support WPA. Furthermore, client software is required on the
client. Windows XP and Windows 2000 with Service Pack 3 do include the client software that
supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA.
Consult the product document for your wireless adapter and WPA client software for instructions
on configuring WPA settings.
Note
: Not all wireless adapters support WPA2. Furthermore, client software is required on the
client. Make sure your client card supports WPA2. Consult the product document for your wireless
adapter and WPA2 client software for instructions on configuring WPA2 settings.
To configure WPA-PSK and WPA2-PSK, follow these steps:
1.
Log in at the default LAN address of
with the default user name of
admin
and default password of
password
, or using whatever LAN address and password you
have set up.
2.
Click
WEP/WPA Settings
in the Security menu of the WG102.
Figure 3-20:
WEP/WPA Settings menu
Page 55 / 118
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG102
Basic Installation and Configuration
3-33
202-10064-02, June 2005
3.
Choose
WPA-PSK and WPA2-PSK
from the list.
4.
Enter the pre-shared key passphrase.
5.
Click
Apply
to save your settings.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top