Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102

2-2

Introduction

v1.0, September 2005

Key Features

The WAG102 Access Point is easy-to-use and provides solid wireless and networking support.

The following standards and conventions are supported:

•

Standards Compliant

.

The Wireless Access Point complies with the IEEE 802.11a/g for

Wireless LANs.

•

WEP support.

Support for WEP is included. 64-bit, 128-bit, and 152-bit keys are supported.

•

DHCP Client Support.

DHCP provides a dynamic IP address to PCs and other devices upon

request. The WAG102 can act as a client and obtain information from your DHPC server.

•

SNMP Support.

Support for Simple Network Management Protocol (SNMP) Management

Information Base (MIB) management.

The NETGEAR WAG102 provides solid functionality, including these features:

•

Multiple Operating Modes

–

Wireless Access Point. Operates as a standard 802.11a/g.

–

Point-to-Point Bridge. In this mode, the WAG102 only communicates with another

bridge-mode wireless station. You must enter the MAC address (physical address) of the

other bridge-mode wireless station in the field provided. WEP should be used to protect

this communication.

–

Point-to-Multi-Point Bridge. Select this only if this WAG102 is the “Master” for a group

of bridge-mode wireless stations. The other bridge-mode wireless stations must be set to

Point-to-Point Bridge mode, using this WAG102's MAC address. They then send all

traffic to this “Master”, rather than communicate directly with each other. WEP should be

used to protect this traffic.

–

Wireless Repeater. In this half-duplex mode, the WAG102 only communicates with

another repeater-mode wireless station. You must enter the MAC address of the root

access point. WEP should be used to protect this communication.

•

Upgradeable Firmware.

Firmware is stored in a flash memory and can be upgraded easily,

using only your Web browser, and can be upgraded remotely.

•

Access Control.

The Access Control MAC address filtering feature can ensure that only

trusted wireless stations can use the WAG102 to gain access to your LAN.

•

Simple Configuration.

If the default settings are unsuitable, they are easy to change.

Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102

Introduction

2-3

v1.0, September 2005

•

Hidden Mode.

The SSID is not broadcast, assuring only clients configured with the correct

SSID can connect.

•

Secure Telnet Command Line Interface.

The Telnet command line interface enables direct

access over the serial port and easy scripting of configuration of multiple WAG102s across an

extensive network via the Ethernet interface. An SSH client is required.

•

Configuration Backup.

Configuration settings can be backed up to a file and restored.

•

Secure and Economical Operation.

Adjustable power output allows more secure or

economical operation.

•

Power over Ethernet.

Power can be supplied to the WAG102 over the Ethernet port from any

802.3af compliant mid-span or end-span source such as the NETGEAR FSM7326P Managed

Power over Ethernet Layer 3 managed switch.

•

Autosensing Ethernet Connection with

Auto Uplink

I

nterface.

Connects to 10/100 Mbps

IEEE 802.3 Ethernet networks.

•

LED Indicators.

Power, test, LAN speed, LAN activity, and wireless activity are easily

identified.

802.11a/g Standards-based Wireless Networking

The WAG102 ProSafe Dual Band Wireless Access Point provides a bridge between Ethernet wired

LANs and 802.11a/g compatible wireless LAN networks. It provides connectivity between

Ethernet wired networks and radio-equipped wireless notebook systems, desktop systems, print

servers, and other devices. Additionally, the WAG102 supports the following wireless features:

•

Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure,

retransmission of unacknowledged frames)

•

RTS/CTS handshake

•

Beacon generation

•

Packet fragmentation and reassembly

•

Short or long preamble

•

Roaming among access points on the same subnet

Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102

2-4

Introduction

v1.0, September 2005

Autosensing Ethernet Connections with Auto Uplink

The WAG102 can connect to a standard Ethernet network. The LAN interface is autosensing and

capable of full-duplex or half-duplex operation.

The wireless access point incorporates Auto Uplink

TM

technology. The Ethernet port will

automatically sense whether the Ethernet cable plugged into the port should have a ‘normal’

connection such as to a computer or an ‘uplink’ connection such as to a switch or hub. That port

will then configure itself to the correct configuration. This feature also eliminates any concerns

about crossover cables, as Auto Uplink will accommodate either type of cable to make the right

connection.

Compatible and Related NETGEAR Products

For a list of compatible products from other manufacturers, see the Wireless Ethernet

Compatibility Alliance Web site (WECA, see

).

The following NETGEAR products work with the WAG102 Access Point:

•

WAG511 ProSafe 108 Mbps Dual Band PC Card

•

WAG311 ProSafe 108 Mbps Dual Band PCI Card

•

WG311T 802.11g 108 Mbps Wireless PCI Card

•

WG511T 802.11g 108 Mbps Wireless CardBus Adapter

•

WG511 802.11g 54 Mbps Wireless CardBus Adapter

•

WG111 801.11g 54 Mbps Wireless Bridge

System Requirements

Before installing the WAG102, make sure your system meets these requirements:

•

A 10/100 Mbps Local Area Network device such as a hub or switch

•

The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the

package, or one like it

•

A 100-240 V, 50-60 HZ AC power source

•

A Web browser for configuration such as Microsoft Internet Explorer 6.0 or above, or

Netscape Navigator 4.78 or above

•

At least one computer with the TCP/IP protocol installed

•

802.11b or 802.11b-compliant devices, such as the NETGEAR WG511 Wireless Adapter

Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102

Introduction

2-5

v1.0, September 2005

What’s In the Box?

The product package should contain the following items:

•

WAG102 ProSafe Dual Band Wireless Access Point

•

Power adapter and cord (12 V dc, 1 A)

•

Straight through Category 5 Ethernet cable

•

WAG102 ProSafe Dual Band Wireless Access Point Installation Guide

•

Resource CD for the NETGEAR WAG102 ProSafe Dual Band Wireless Access Point

which

includes this manual.

•

Support Registration card

Contact your reseller or customer support in your area if there are any missing or damaged parts.

You can refer to the Support Information Card for the telephone number of customer support in

your area. You should keep the Support Information card, along with the original packing

materials, and use the packing materials to repack the WAG102 if you need to return it for repair.

To qualify for product updates and product warranty registrations, we encourage you to register on

the NETGEAR Web site at:

.

Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102

2-6

Introduction

v1.0, September 2005

Hardware Description

The WAG102 front and rear hardware functions are described below.

Front Panel

The following table explains the LED indicators:

Figure 2-1

LED

DESCRIPTION

PWR

Power Indicator

Off

No power.

On

Power is on.

TEST

Self Test Indicator

Blink

Indicates self test, loading software, or system fault (if continues).

Note:

This LED may blink for a minute before going off.

100 LINK/ACT

Ethernet LAN Speed Indicator

Off

Indicates no 100 Mbps Ethernet link detected

Green Solid On

100 Mbps Fast Ethernet link detected, no activity

Green Blink

Indicates data traffic on the 100 Mbps Ethernet LAN.

10 LINK/ACT

Ethernet LAN Link Activity Indicator

Off

Indicates no 10 Mbps Ethernet link detected.

Green Solid On

10 Mbps Fast Ethernet link detected, no activity.

Green Blink

Indicates data traffic on the 10 Mbps Ethernet LAN.