1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. R7000
    5. /
  5. 3
Page 11 / 169 Scroll up to view Page 6 - 10
11
Nighthawk AC1900
Smart
WiFi
Router Model
R7000
Rear Panel
The rear panel has the connections and buttons shown in the following figure.
USB 2.0
Ethernet
Internet
Power
Power
port
LAN ports 1–4
Reset
button
port
connector
On/Off
Figure 3. Router rear panel
Pressing the Reset button restores the factory settings. See
Factory Settings
on page
164.
Ethernet ports
1-4
The LED color indicates the speed: white for Gigabit Ethernet connections and amber for 100
Mbps or 10 Mbps Ethernet connections.
•
Solid
. A powered-on device is connected to the Ethernet port.
•
Blinking
. The port is sending or receiving traffic.
•
Off
. No device is connected to this Ethernet port.
WiFi On/Off
button with LED
Pressing this button for two seconds turns the 2.4 GHz and 5 GHz WiFi radios on and off.
If this LED is lit, the WiFi radios are on. If this LED is off, the WiFi radios are turned off and you
cannot use WiFi to connect to the router.
WPS button with
LED
This button lets you use WPS to join the WiFi network without typing the WiFi password. The
WPS LED blinks white during this process and then lights solid white.
Table 1.
LED and button descriptions
(Continued)
LED
Description
Page 12 / 169
12
Nighthawk AC1900
Smart
WiFi
Router Model
R7000
Position Your Router
The router lets you access your network anywhere within the operating range of your wireless
network. However, the operating distance or range of your wireless connection can vary
significantly depending on the physical placement of your router. For example, the thickness
and number of walls the wireless signal passes through can limit the range.
Additionally, other wireless access points in and around your home might affect your router’s
signal. Wireless access points are routers, repeaters, WiFi range extenders, or any other
device that emits a wireless signal for network access.
To position your router:
1.
Place your router near the center of the area where your computers and other devices
operate, and within line of sight to your wireless devices.
2.
Make sure that the router is within reach of an AC power outlet and near Ethernet cables
for wired computers.
3.
Place the router in an elevated location, minimizing the number walls and ceilings between
the router and your other devices.
4.
Place the router away from electrical devices such as these:
•
Ceiling fans
•
Home security systems
•
Microwaves
•
Computers
•
Base of a cordless phone
•
2.4 GHz cordless phone
5.
Place the router away from large metal surfaces, large glass surfaces, and insulated walls
such as these:
•
Solid metal door
•
Aluminum studs
•
Fish tanks
•
Mirrors
•
Brick
•
Concrete
6.
(Optional) If you have adjacent access points, use different radio frequency channels to
reduce interference.
Page 13 / 169
13
Nighthawk AC1900
Smart
WiFi
Router Model
R7000
Cable Your Router
The following image shows how to cable your router:
Figure 4. Router cabling
To cable your router:
1.
Unplug your modem’s power, leaving the modem connected to the wall jack for your
Internet service.
If your modem has a battery backup, remove the battery.
2.
Plug in and turn on your modem.
If your modem has a battery backup, replace the battery.
3.
Connect your modem to the Internet port of your router with the yellow Ethernet cable that
came with your router.
4.
Connect the power adapter to your router and plug the power adapter into an outlet.
5.
Press the
Power On/Off
button on the rear panel of the router.
Page 14 / 169
14
2
2.
Connect to the Network and
Access the Router
This chapter contains the following sections:
•
Connect to the Network
•
Types of Logins
•
Use an Internet Browser to Access the Router
•
Change the Language
•
Access the Router with NETGEAR genie Apps
Page 15 / 169
15
Nighthawk AC1900
Smart
WiFi
Router Model
R7000
Connect to the Network
You can connect to the router’s network through a wired or WiFi connection. If you set up
your computer to use a static IP address, change the settings so that it uses Dynamic Host
Configuration Protocol (DHCP).
Wired Connection
You can connect your computer to the router using an Ethernet cable and join the router’s
local area network (LAN).
To connect your computer to the router with an Ethernet cable:
1.
Make sure that the router has power (its Power LED is lit).
2.
Connect an Ethernet cable to an Ethernet port on your computer.
3.
Connect the other end of the Ethernet cable to one of the numbered Ethernet ports.
Your computer connects to the local area network (LAN). A message might display on
your computer screen to notify you that an Ethernet cable is connected.
WiFi Connection
You can connect to the router’s WiFi network with Wi-Fi Protected Setup (WPS) or you can
find and select the WiFi network.
To use WPS to connect to the WiFi network:
1.
Make sure that the router has power (its Power LED is lit).
2.
Check the WPS instructions for your computer or wireless device.
3.
Press the
WPS
button on the router.
4.
Within two minutes, on your computer or WiFi device, press its
WPS
button or follow its
instructions for WPS connections.
Your computer or wireless device connects to the WiFi network.
To find and select the WiFi network:
1.
Make sure that the router has power (its Power LED is lit).
2.
On your computer or wireless device, find and select the WiFi network.
The WiFi network name is on the router’s label.
3.
Join the WiFi network and enter the WiFi password.
The password is on the router’s label.
Your wireless device connects to the WiFi network.

Rate

3.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top