1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. R6200v2
    5. /
  5. 17
Page 81 / 131 Scroll up to view Page 76 - 80
Administration
81
R6200v2 Smart WiFi Router
Update the Router Firmware
The router firmware (routing software) is stored in flash memory. You can update the
firmware from the Administration menu on the Advanced tab. You might see a message at
the top of the genie screens when new firmware is available for your product.
You can use the Check button on the Router Update screen to check if new firmware is
available, and to update your product.
To check for new firmware and update your router:
1.
Select
ADVANCED > Administration > Router Update
.
2.
Click the
Check
button.
The router finds new firmware information if it is available.
3.
Click the
Yes
button.
The router locates and downloads the firmware and begins the update.
WARNING:
To avoid the risk of corrupting the firmware, do not interrupt the
update process. For example, do not close the browser, click a
link, or load a new page. Do not turn off the router..
When the upload is complete, your router restarts. The upgrade process typically takes
about 1oneminute. Read the new firmware release notes to find out if you need to
reconfigure the router after upgrading.
Page 82 / 131
Administration
82
R6200v2 Smart WiFi Router
View Router Status
To view router status and usage information:
Select
Advanced Home
or select
Administration > Router Status
.
Router Information
•
Hardware Version
. The router model.
•
Firmware Version
. The version of the router firmware. It changes if you upgrade the
router firmware.
•
GUI Language Version
. The localized language of the user interface.
•
LAN Port
.
-
MAC Address
. The Media Access Control address. This is the unique physical
address used by the Ethernet (LAN) port of the router.
-
IP Address
. The IP address used by the Ethernet (LAN) port of the router. The
default is 192.168.1.1.
-
DHCP
. Identifies whether the router’s built-in DHCP server is active for devices on the
LAN.
Internet Port
•
MAC Address
. The Media Access Control address, which is the unique physical address
used by the Internet (WAN) port of the router.
•
IP Address
. The IP address used by the Internet (WAN) port of the router. If no address
is shown or the address is 0.0.0.0, the router cannot connect to the Internet.
Page 83 / 131
Administration
83
R6200v2 Smart WiFi Router
•
Connection
. This shows if the router is using a fixed IP address on the WAN. If the value
is DHCP Client, the router obtains an IP address dynamically from the ISP.
•
IP Subnet Mask
. The IP subnet mask used by the Internet (WAN) port of the router.
•
Domain Name Server
. The Domain Name Server addresses used by the router. A
Domain Name Server translates human-language URLs such as www.netgear.com into
IP addresses.
Show Statistics Button
To view statistics:
1.
Select
Advanced Home
or select
Administration > Router Status
.
2.
In the Internet Port pane, click the
Show Statistics
button.
The following information is displayed:
•
System Up Time
. The time elapsed since the router was last restarted.
•
Port
. The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port,
the screen displays:
-
Status
. The link status of the port.
-
TxPkts
. The number of packets transmitted on this port since reset or manual
clear.
-
RxPkts
. The number of packets received on this port since reset or manual clear.
-
Collisions
. The number of collisions on this port since reset or manual clear.
-
Tx B/s
. The current transmission (outbound) bandwidth used on the WAN and
LAN ports.
-
Rx B/s
. The current reception (inbound) bandwidth used on the WAN and LAN
ports.
-
Up Time
. The time elapsed since this port acquired the link.
-
Poll Interval
. The interval at which the statistics are updated in this screen.
To change the polling frequency, enter a time in seconds in the Poll Interval field and click
the
Set Interval
button.
To stop the polling entirely, click the
Stop
button.
Page 84 / 131
Administration
84
R6200v2 Smart WiFi Router
Connection Status Button
To view the Internet connection status:
1.
Select
Advanced Home
or select
Administration > Router Status
.
2.
In the Internet Port pane, click the
Connection Status
button.
The following information displays:
•
IP Address
. The IP address that is assigned to the router.
•
Subnet Mask
. The subnet mask that is assigned to the router.
•
Default Gateway
. The IP address for the default gateway that the router
communicates with.
•
DHCP Server
. The IP address for the Dynamic Host Configuration Protocol server
that provides the TCP/IP configuration for all the computers that are connected to the
router.
•
DNS Server
. The IP address of the Domain Name Service server that provides
translation of network names to IP addresses.
•
Lease Obtained
. The date and time when the lease was obtained.
•
Lease Expires
. The date and time that the lease expires.
Click the
Release
button to return the status of all items to 0.
Click the
Renew
button to refresh the items.
Click the
Close Window
button to close the Connection Status screen.
Page 85 / 131
Administration
85
R6200v2 Smart WiFi Router
Wireless Settings (2.4 GHz and 5 GHz)
The following settings are displayed:
•
Name (SSID
). The wireless network name (SSID) that the router uses.
•
Region
. The geographic region where the router is being used. It might be illegal to use
the wireless features of the router in some parts of the world.
•
Channel
. The operating channel of the wireless port. The default channel at 2.4 GHz is
Auto. When Auto is selected, the router finds the best channel available. For the 2.4 GHz
setting, you can select channel 1 - 11 if your region is North America. In other regions,
you can select channel 1-13.
The default channel at 5 GHz is 53. For the 5 GHz setting, you can select channels 36,
40, 44, 48, 149, 157, and 161.
•
Mode
. The wireless communication mode. At 2.4 GHz, Up to 300 Mbps, Up to 145 Mbps,
or Up to 54 Mbps. At 5 GHz, Up to 867 Mbps, Up to 400 Mbps, or Up to 173 Mbps.
•
Wireless AP
. Indicates whether the radio feature of the router is enabled. If this feature is
not enabled, the WiFi LED on the front panel is off.
•
Broadcast Name
. Indicates whether the router is broadcasting its SSID.
•
Wireless Isolation
. Wireless isolation prevents wireless clients from communicating with
each other when they join the wireless network.
•
Wi-Fi Protected Setup
. Indicates whether WPS is configured for this network.
View Logs
The log is a detailed record of the websites you have accessed or attempted to access and
other activities. Up to 256
entries are stored in the log. Log entries appear only when
keyword blocking is enabled and no log entries are made for the trusted user.
To view logs:
Select
ADVANCED > Administration > Logs
.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top