1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. R6200
    5. /
  5. 21
Page 101 / 130 Scroll up to view Page 96 - 100
Advanced Settings
101
Dual Band 11ac WiFi Router R6200
6.
Click
Add Service
to display the following screen:
FPO
7.
In the Service Name field, type a descriptive service name.
8.
In the Service User list, select
Any
(the default) to allow this service to be used by any
computer on the Internet. Otherwise, select
Single address
, and enter the IP address of
one computer to restrict the service to a particular computer.
9.
Select the service type, either
TCP
or
UDP
or both (
TCP/UDP
). If you are not sure, select
TCP/UDP.
10.
In the Triggering Port field, enter the number of the outbound traffic port that will cause the
inbound ports to be opened.
11.
Enter the inbound connection port information in the Connection Type, Starting Port, and
Ending Port fields.
12.
Click
Apply
. The service appears in the Port Triggering Portmap table.
Dynamic DNS
If your Internet service provider (ISP) gave you a permanently assigned IP address, you can
register a domain name and have that name linked with your IP address by public Domain
Name Servers (DNS). However, if your Internet account uses a dynamically assigned IP
address, you do not know your IP address in advance, and the address can change
frequently. In this case, you can use a commercial Dynamic DNS service. This type of service
lets you register your domain to their IP address and forwards traffic directed at your domain
to your frequently changing IP address.
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic
DNS service does not work because private addresses are not routed on the Internet.
Your router contains a client that can connect to the Dynamic DNS service provided by
DynDNS.org. First visit their website at
and obtain an account and
Page 102 / 130
Advanced Settings
102
Dual Band 11ac WiFi Router R6200
host name that you configure in the router. Then, whenever your ISP-assigned IP address
changes, your router automatically contacts the Dynamic DNS service provider, logs in to
your account, and registers your new IP address. If your host name is hostname, for
example, you can reach your router at
.
To set up Dynamic DNS:
1.
Select
Advanced > Advanced Setup > Dynamic DNS
:
2.
Register for an account with one of the Dynamic DNS service providers whose names
appear in the Service Provider list. For example, for DynDNS.org, select
www.dyndns.org
.
3.
Select the
Use a Dynamic DNS Service
check box.
4.
Select the name of your Dynamic DNS service provider.
5.
Type the host name (or domain name) that your Dynamic DNS service provider gave you.
6.
Type the user name for your Dynamic DNS account. This is the name that you use to log in
to your account, not your host name.
7.
Type the password (or key) for your Dynamic DNS account.
8.
If your Dynamic DNS provider allows the use of wildcards in resolving your URL, you can
select the
Use Wildcards
check box to activate this feature.
For example, the wildcard feature causes
*.yourhost.dyndns.org
to be aliased to the
same IP address as yourhost.dyndns.org.
9.
Click
Apply
to save your configuration.
Page 103 / 130
Advanced Settings
103
Dual Band 11ac WiFi Router R6200
Static Routes
Static routes provide additional routing information to your router. Typically, you do not need
to add static routes. You have to configure static routes only for unusual cases such as
multiple routers or multiple IP subnets on your network.
As an example of when a static route is needed, consider the following case:
•
Your primary Internet access is through a cable modem to an ISP.
•
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.1.100.
•
Your company’s network address is 134.177.0.0.
When you first configured your router, two implicit static routes were created. A default route
was created with your ISP as the gateway, and a second static route was created to your
local network for all 192.168.1.x addresses. With this configuration, if you attempt to access a
device on the 134.177.0.0 network, your router forwards your request to the ISP. The ISP
forwards your request to the company where you are employed, and the request is likely to
be denied by the company’s firewall.
In this case you have to define a static route, telling your router that 134.177.0.0 should be
accessed through the ISDN router at 192.168.1.100. In this example:
•
The Destination IP Address and IP Subnet Mask fields specify that this static route
applies to all 134.177.x.x addresses.
•
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.1.100.
•
A metric value of 1 will work since the ISDN router is on the LAN.
•
Private is selected only as a precautionary security measure in case RIP is activated.
To set up a static route:
1.
Select
Advanced > Advanced Setup > Static Routes
Page 104 / 130
Advanced Settings
104
Dual Band 11ac WiFi Router R6200
2.
Click
Add
to display the following screen:
3.
In the Route Name field, type a name for this static route (for identification purposes only.)
4.
Select the
Private
check box if you want to limit access to the LAN only. If Private is
selected, the static route is not reported in RIP.
5.
Select the
Active
check box to make this route effective.
6.
Type the destination IP address of the final destination.
7.
Type the IP subnet mask for this destination. If the destination is a single host, type
255.255.255.255
.
8.
Type the gateway IP address, which has to be a router on the same LAN segment as the
R6200 WiFi Router.
9.
Type a number from 1 through 15 as the metric value.
This value represents the number of routers between your network and the destination.
Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
10.
Click
Apply
to add the static route.
Page 105 / 130
Advanced Settings
105
Dual Band 11ac WiFi Router R6200
Remote Management
The remote management feature lets you upgrade or check the status of your R6200 WiFi
Router over the Internet.
To set up remote management:
1.
Select
Advanced > Advanced Setup > Remote Management
.
Note:
Be sure to change the router’s default login password to a secure
password. The ideal password contains no dictionary words from any language
and contains upper-case and lower-case letters, numbers, and symbols. It can
be up to 30 characters.
2.
Select the
Turn Remote Management On
check box.
3.
Under Allow Remote Access By, specify the external IP addresses to be allowed to access
the router’s remote management.
Note:
For enhanced security, restrict access to as few external IP addresses
as practical.
•
To allow access from a single IP address on the Internet, select
Only This
Computer
. Enter the IP address that will be allowed access.
•
To allow access from a range of IP addresses on the Internet, select
IP Address
Range
. Enter a beginning and ending IP address to define the allowed range.
•
To allow access from any IP address on the Internet, select
Everyone
.
4.
Specify the port number for accessing the management interface.
Normal web browser access uses the standard HTTP service port 80. For greater
security, enter a custom port number for the remote web management interface. Choose

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top