NETGEAR MR814v3 Router Manual PDF (Setup & Configuration Guide)

Page 136 / 162 Scroll up to view Page 131 - 135

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

C-24

Preparing Your Network

202-10039-01

Page 137 / 162

Wireless Networking Basics

D-1

202-10039-01

Appendix D

Wireless Networking Basics

This chapter provides an overview of Wireless networking.

Wireless Networking Overview

The MR814 v3 router conforms to the Institute of Electrical and Electronics Engineers (IEEE)

802.11b standard for wireless LANs (WLANs). On an 802.11b wireless link, data is encoded using

direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio

spectrum at 2.5GHz. The maximum data rate for the wireless link is 11 Mbps, but it will

automatically back down from 11 Mbps to 5.5, 2, and 1 Mbps when the radio signal is weak or

when interference is detected.

The 802.11b standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet

Compatibility Alliance (WECA, see

http://www.wi-fi.net

), an industry standard group promoting

interoperability among 802.11b devices. The 802.11b standard offers two methods for configuring

a wireless network - ad hoc and infrastructure.

Infrastructure Mode

With a wireless Access Point, you can operate the wireless LAN in the infrastructure mode. This

mode provides wireless connectivity to multiple wireless network devices within a fixed range or

area of coverage, interacting with wireless nodes via an antenna.

In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet

data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple Access

Points via a wired Ethernet backbone can further extend the wireless network coverage. As a

mobile computing device moves out of the range of one access point, it moves into the range of

another. As a result, wireless clients can freely roam from one Access Point domain to another and

still maintain seamless network connection.

Page 138 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

D-2

Wireless Networking Basics

202-10039-01

Ad Hoc Mode (Peer-to-Peer Workgroup)

In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed

points to the network - each node can generally communicate with any other node. There is no

Access Point involved in this configuration. This mode enables you to quickly set up a small

wireless workgroup and allows workgroup members to exchange data or share printers as

supported by Microsoft networking in the various Windows operating systems. Some vendors also

refer to ad hoc networking as peer-to-peer group networking.

In this configuration, network packets are directly sent and received by the intended transmitting

and receiving stations. As long as the stations are within range of one another, this is the easiest

and least expensive way to set up a wireless network.

Network Name: Extended Service Set Identification (ESSID)

The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification

(SSID). In an ad hoc wireless network with no access points, the Basic Service Set Identification

(BSSID) is used. In an infrastructure wireless network that includes an access point, the ESSID is

used, but may still be referred to as SSID.

An SSID is a thirty-two character (maximum) alphanumeric key identifying the name of the

wireless local area network. Some vendors refer to the SSID as network name. For the wireless

devices in a network to communicate with each other, all devices must be configured with the

same SSID.

Wireless Channels

IEEE 802.11 wireless nodes communicate with each other using radio frequency signals in the

ISM (Industrial, Scientific, and Medical) band between 2.4 GHz and 2.5 GHz. Neighboring

channels are 5 MHz apart. However, due to spread spectrum effect of the signals, a node sending

signals using a particular channel will utilize frequency spectrum 12.5 MHz above and below the

center channel frequency. As a result, two separate wireless networks using neighboring channels

(for example, channel 1 and channel 2) in the same general vicinity will interfere with each other.

Applying two channels that allow the maximum channel separation will decrease the amount of

channel cross-talk, and provide a noticeable performance increase over networks with minimal

channel separation.

Page 139 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

Wireless Networking Basics

D-3

202-10039-01

The radio frequency channels used are listed in

Table 8-3

:

Note:

The available channels supported by the wireless products in various countries are different.

The preferred channel separation between the channels in neighboring wireless networks is 25

MHz (5 channels). This means that you can apply up to three different channels within your

wireless network. There are only 11 usable wireless channels in the United States. It is

recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as

these three channels do not overlap.

Table 8-3.

802.11 Radio Frequency Channels

Channel

Center Frequency

Frequency Spread

1

2412 MHz

2399.5 MHz - 2424.5 MHz

2

2417 MHz

2404.5 MHz - 2429.5 MHz

3

2422 MHz

2409.5 MHz - 2434.5 MHz

4

2427 MHz

2414.5 MHz - 2439.5 MHz

5

2432 MHz

2419.5 MHz - 2444.5 MHz

6

2437 MHz

2424.5 MHz - 2449.5 MHz

7

2442 MHz

2429.5 MHz - 2454.5 MHz

8

2447 MHz

2434.5 MHz - 2459.5 MHz

9

2452 MHz

2439.5 MHz - 2464.5 MHz

10

2457 MHz

2444.5 MHz - 2469.5 MHz

11

2462 MHz

2449.5 MHz - 2474.5 MHz

12

2467 MHz

2454.5 MHz - 2479.5 MHz

13

2472 MHz

2459.5 MHz - 2484.5 MHz

Page 140 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

D-4

Wireless Networking Basics

202-10039-01

Authentication and WEP

The absence of a physical connection between nodes makes the wireless links vulnerable to

eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11

standard has defined two types of authentication methods, Open System and Shared Key. With

Open System authentication, a wireless PC can join any network and receive any messages that are

not encrypted. With Shared Key authentication, only those PCs that possess the correct

authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an

Open System network.

Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured

to operate in Shared Key authentication mode. There are two shared key methods implemented in

most commercially available products, 64-bit and 128-bit WEP data encryption.

802.11b Authentication

The 802.11b standard defines several services that govern how two 802.11b devices communicate.

The following events must occur before an 802.11b Station can communicate with an Ethernet

network through an access point such as the one built in to the MR814 v3:

1.

Turn on the wireless station.

2.

The station listens for messages from any access points that are in range.

3.

The station finds a message from an access point that has a matching SSID.

4.

The station sends an authentication request to the access point.

5.

The access point authenticates the station.

6.

The station sends an association request to the access point.

7.

The access point associates with the station.

8.

The station can now communicate with the Ethernet network through the access point.

An access point must authenticate a station before the station can associate with the access point or

communicate with the network. The IEEE 802.11b standard defines two types of authentication:

Open System and Shared Key.

•

Open System Authentication

allows any device to join the network, assuming that the device

SSID matches the access point SSID. Alternatively, the device can use the “ANY” SSID

option to associate with any available Access Point within range, regardless of its SSID.

Rate

Popular NETGEAR Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share