NETGEAR MR814v3 Router Manual PDF (Setup & Configuration Guide)

Page 111 / 162 Scroll up to view Page 106 - 110

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

Network, Routing, Firewall, and Basics

B-15

202-10039-01

The MR814 v3 router incorporates Auto Uplink

TM

technology (also called MDI/MDIX). Each

LOCAL Ethernet port will automatically sense whether the Ethernet cable plugged into the port

should have a normal connection (e.g. connecting to a computer) or an uplink connection (e.g.

connecting to a router, switch, or hub). That port will then configure itself to the correct

configuration. This feature also eliminates the need to worry about crossover cables, as Auto

Uplink

TM

will accommodate either type of cable to make the right connection.

Page 112 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

B-16

Network, Routing, Firewall, and Basics

202-10039-01

Page 113 / 162

Preparing Your Network

C-1

202-10039-01

Appendix C

Preparing Your Network

This appendix describes how to prepare your network to connect to the Internet through the

MR814 v3 Cable/DSL Wireless Router and how to verify the readiness of broadband Internet

service from an Internet service provider (ISP).

What You Need To Use a Router with a Broadband Modem

You need to prepare these three things before you begin:

Cabling and Computer Hardware

To use the MR814 v3 router on your network, each computer must have an 802.11g or 802.11b

wireless adapter or an installed Ethernet Network Interface Card (NIC) and an Ethernet cable. If

the computer will connect to your network using an Ethernet NIC at 100 Mbps, you must use a

Category 5 (Cat 5) cable such as the one provided with your router. For an explanation of Ethernet

cabling, see

“Ethernet Cabling“ on page B-11

. The cable or DSL broadband modem must provide

a standard 10 Mbps (10BASE-T) or 100 Mbps (100BASE-Tx) Ethernet interface.

Computer Network Configuration Requirements

The MR814 v3 includes a built-in web Configuration Manager. To access the configuration menus

on the MR814 v3, your must use a Java-enabled web browser program which supports HTTP

uploads such as Microsoft Internet Explorer or Netscape Navigator. Use Internet Explorer or

Netscape Navigator 4.0 or above.

Note:

If an ISP technician configured your computer during the installation of a

broadband modem, or if you configured it using instructions provided by your ISP, you

may need to copy the current configuration information for use in the configuration of

your firewall. Write down this information before reconfiguring your computers. Refer

to

“Obtaining ISP Configuration Information for Windows Computers

” on

page C-21

or

“Obtaining ISP Configuration Information for Macintosh Computers

” on

page C-22

for

further information.

Page 114 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

C-2

Preparing Your Network

202-10039-01

For the initial setup of your router, you will need to connect a computer to the router. This

computer has to be set to automatically get its TCP/IP configuration from the router via DHCP.

Note:

For help with DHCP configuration, please use the Windows TCP/IP Configuration

Tutorials on the

MR814 v3 Resource CD (2230-10095-01 )

, or in this appendix.

Internet Configuration Requirements

Depending on how your Internet service set up your account, you may need one or more of these

configuration parameters to connect your router to the Internet:

•

Host and Domain Names

•

ISP Login Name and Password

•

ISP Domain Name Server (DNS) Addresses

•

Fixed IP Address which is also known as Static IP Address

Where Do I Get the Internet Configuration Parameters?

There are several ways you can gather the required Internet connection information.

•

Your Internet service provides all the information needed to connect to the Internet. If you

cannot locate this information, you can ask your Internet service to provide it or you can try

one of the options below.

•

If you have a computer already connected using the Internet, you can gather the configuration

information from that computer.

—

For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the

Ethernet adapter, and click Properties. Record all the settings for each tab page.

—

For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry

for the Ethernet adapter, and click Properties. Record all the settings for each tab page.

—

For Macintosh computers, record the settings in the TCP/IP or Network control panel.

•

You may also refer to the

MR814 v3 Resource CD (2230-10095-01 )

for the NETGEAR

Router ISP Guide which provides Internet connection information for many ISPs.

Once you locate your Internet configuration parameters, you may want to record them on the page

below.

Page 115 / 162

Reference Manual for the MR814 v3 Cable/DSL Wireless Router

Preparing Your Network

C-3

202-10039-01

Record Your Internet Connection Information

Print this page. Fill in the configuration parameters from your Internet Service Provider (ISP).

ISP Login Name:

The login name and password are case sensitive and must be entered exactly as

given by your ISP. Some ISPs use your full e-mail address as the login name. The Service Name is

not required by all ISPs. If you connect using a login name and password, enter the following:

Login Name: ______________________________

Password: ____________________________

Service Name: _____________________________

Fixed or Static IP Address:

If you have a static IP address, record the following information. For

example, 169.254.141.148 could be a valid IP address.

Fixed or Static Internet IP Address: ______

______

Gateway IP Address: ______

______

Subnet Mask: ______

______

ISP DNS Server Addresses:

If you were given DNS server addresses, fill in the following:

Primary DNS Server IP Address: ______

______

Secondary DNS Server IP Address: ______

______

Host and Domain Names:

Some ISPs use a specific host or domain name like

CCA7324-A

or

home

. If you haven’t been given host or domain names, you can use the following examples as a

guide:

•

If your main e-mail account with your ISP is

[email protected]

, then use

aaa

as your host name.

Your ISP might call this your account, user, host, computer, or system name.

•

If your ISP’s mail server is

mail.xxx.yyy.com

, then use

xxx.yyy.com

as the domain name.

ISP Host Name: _________________________

ISP Domain Name: _______________________

For Wireless Access:

See the configuration worksheet at

“Information to Gather Before Changing

Basic Wireless Settings“ on page 4-7

.

Preparing Your Computers for TCP/IP Networking

Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/

Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its

networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/

IP is probably already installed as well.

Rate

Popular NETGEAR Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share