1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FVS318N
    5. /
  5. 29
Page 141 / 414 Scroll up to view Page 136 - 140
Firewall Protection
141
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
3.
Enter the settings as explained in
Table 33
on page 132. In addition to selections from the
Service, Action, and Log drop-down lists, you need to make selections from the following
drop-down lists:
•
WAN Destination IP Address
•
LAN Users (This drop-down list is available only when the WAN mode is Classical
Routing. When the WAN mode is NAT, your network presents only one IP address to
the Internet.)
•
WAN Users
Unless your selection from the Action drop-down list is BLOCK always, you also need to
make selections from the following drop-down lists:
•
Select Schedule
•
Send to Lan Server
•
Bandwidth Profile
The following configuration is optional:
•
Translate to Port Number
4.
Click
Apply
to save your changes. The new rule is now added to the Inbound Services
table.
IPv6 LAN WAN Inbound Rules
To create a new IPv6 LAN WAN inbound rule:
1.
In the upper right of the LAN WAN Rules screen, select the
IPv6
radio button. The screen
displays the IPv6 settings (see
Figure 62
on page 136).
2.
Click the
Add
table button under the Inbound Services table. The Add LAN WAN Inbound
Service screen for IPv6 displays:
Figure 66.
Page 142 / 414
Firewall Protection
142
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
3.
Enter the settings as explained in
Table 33
on page 132. In addition to selections from the
Service, Action, and Log drop-down lists, you need to make selections from the following
drop-down lists:
•
LAN Users
•
WAN Users
Unless your selection from the Action drop-down list is BLOCK always, you also need to
make a selection from the following drop-down list:
•
Select Schedule
4.
Click
Apply
to save your changes. The new rule is now added to the Inbound Services
table.
Configure DMZ WAN Rules
The firewall rules for traffic between the DMZ and the Internet are configured on the DMZ
WAN Rules screen. The default outbound policy is to block all traffic from and to the Internet.
You can then apply firewall rules to allow specific types of traffic either going out from the
DMZ to the Internet (outbound) or coming in from the Internet to the DMZ (inbound).
There is no drop-down list that lets you set the default outbound policy as there is on the LAN
WAN Rules screen. You can change the default outbound policy by enabling all outbound
traffic and then blocking only specific services from passing through the wireless VPN
firewall. You do so by adding outbound services rules (see
Create DMZ WAN Outbound
Service Rules
on page 145).
To access the DMZ WAN Rules screen for IPv4 or to make changes to existing IPv4
rules:
Select
Security > Firewall > DMZ WAN Rules
.
In the upper right of the screen, the IPv4
radio button is selected by default. The DMZ WAN Rules screen displays the IPv4 settings.
(The following figure contains examples.)
Page 143 / 414
Firewall Protection
143
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Figure 67.
To make changes to an existing outbound or inbound service rule, in the Action column to the
right of to the rule, click one of the following table buttons:
•
Up
. Moves the rule up one position in the table rank.
•
Down
. Moves the rule down one position in the table rank.
•
Edit
.
Allows you to make any changes to the definition of an existing rule. Depending on
your selection, one of the following screens displays:
-
Edit DMZ WAN Outbound Service screen for IPv4 (identical to
Figure 69
on
page 145)
-
Edit DMZ WAN Inbound Service screen for IPv4 (identical to
Figure 71
on page 148)
To access the DMZ WAN Rules screen for IPv6 or to make changes to existing IPv6
rules:
1.
Select
Security > Firewall > DMZ WAN Rules
. The Firewall submenu tabs display with
the DMZ WAN Rules screen for IPv4 in view.
2.
In the upper right of the screen, select the
IPv6
radio button. The DMZ WAN Rules screen
displays the IPv6 settings. (The following figure contains examples.)
Page 144 / 414
Firewall Protection
144
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Figure 68.
To make changes to an existing outbound or inbound service rule, in the Action column to the
right of to the rule, click one of the following table buttons:
•
Up
. Moves the rule up one position in the table rank.
•
Down
. Moves the rule down one position in the table rank.
•
Edit
.
Allows you to make any changes to the definition of an existing rule. Depending on
your selection, one of the following screens displays:
-
Edit DMZ WAN Outbound Service screen for IPv6 (identical to
Figure 70
on
page 146)
-
Edit DMZ WAN Inbound Service screen for IPv6 (identical to
Figure 72
on page 149)
To enable, disable, or delete one or more IPv4 or IPv6 rules:
1.
select the check box to the left of each rule that you want to enable, disable, or delete,
or click the
Select All
table button to select all rules.
2.
Click one of the following table buttons:
•
Enable
.
Enables the rule or rules. The ! status icon changes from a gray circle to a
green circle, indicating that the selected rule or rules are enabled. (By default, when a
rule is added to the table, it is automatically enabled.)
•
Disable
.
Disables the rule or rules. The ! status icon changes from a green circle to a
gray circle, indicating that the selected rule or rules are disabled.
•
Delete
.
Deletes the selected rule or rules.
Page 145 / 414
Firewall Protection
145
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Create DMZ WAN Outbound Service Rules
You can change the default outbound policy or define rules that specify exceptions to the
default outbound policy. By adding custom rules, you can block or allow access based on the
service or application, source or destination IP addresses, and time of day. An outbound rule
can block or allow traffic between the DMZ and any external WAN IP address according to
the schedule created on the Schedule screen.
IPv4 DMZ WAN Outbound Service Rules
To create a new IPv4 DMZ WAN outbound rule:
1.
In the upper right of the DMZ WAN Rules screen, select the
IPv4
radio button. The screen
displays the IPv4 settings (see
Figure 67
on page 143).
2.
Click the
Add
table button under the Outbound Services table. The Add DMZ WAN
Outbound Service screen for IPv4 displays:
Figure 69.
3.
Enter the settings as explained in
Table 32
on page 128. In addition to selections from the
Service, Action, and Log drop-down lists, you need to make selections from the following
drop-down lists:
•
DMZ Users
•
WAN Users

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top