1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FVS318N
    5. /
  5. 12
Page 56 / 414 Scroll up to view Page 51 - 55
LAN Configuration
56
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Configure a VLAN Profile
For each VLAN on the wireless VPN firewall, you can configure its profile, port membership,
LAN TCP/IP settings, DHCP options, DNS server, and inter-VLAN routing capability.
To add a VLAN profile:
1.
Select
Network Configuration > LAN Setup
. In the upper right of the screen, the IPv4
radio button is selected by default. The LAN submenu tabs display, with the LAN Setup
screen in view, displaying the IPv4 settings. (The following figure contains some VLAN
profiles as an example.)
Note:
For information about how to manage VLANs, see
Port-Based
VLANs
on page 52. The following information describes how to
configure a VLAN profile.
Figure 29.
2.
Click the
Add
table button under the VLAN Profiles table. The Add VLAN Profile screen
displays:
Page 57 / 414
LAN Configuration
57
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Figure 30.
Page 58 / 414
LAN Configuration
58
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
3.
Enter the settings as explained in the following table:
Table 10.
Add VLAN Profile screen settings
Setting
Description
VLAN Profile
Profile Name
Enter a unique name for the VLAN profile.
VLAN ID
Enter a unique ID number for the VLAN profile. No two VLANs can have the same
VLAN ID number.
Note:
You can enter VLAN IDs from 2 to 4089. VLAN ID 1 is reserved for the
default VLAN; VLAN ID 4094 is reserved for the DMZ interface.
Port Membership
Port 1, Port 2, Port 3,
Port 4, Port 5, Port 6,
Port 7, and
Port 8 / DMZ
Select one, several, or all port check boxes to make the ports members of this
VLAN.
Note:
A port that is defined as a member of a VLAN profile can send and receive
data frames that are tagged with the VLAN ID.
IP Setup
IP Address
Enter the IP address of the wireless VPN firewall (the factory default address is
192.168.1.1).
Note:
Always make sure that the LAN port IP address and DMZ port IP address
are in different subnets.
Note:
If you change the LAN IP address of the VLAN while being connected
through the browser to the VLAN, you are disconnected. You then need to open
a new connection to the new IP address and log in again. For example, if you
change the default IP address 192.168.1.1 to 10.0.0.1, you now need to enter
in your browser to reconnect to the web management interface.
Subnet Mask
Enter the IP subnet mask. The subnet mask specifies the network number portion
of an IP address. Based on the IP address that you assign, the wireless VPN
firewall automatically calculates the subnet mask. Unless you are implementing
subnetting, use 255.255.255.0 as the subnet mask (computed by the wireless
VPN firewall).
DHCP
Disable DHCP Server
If another device on your network is the DHCP server for the VLAN, or if you will
manually configure the network settings of all of your computers, select the
Disable DHCP Server
radio button to disable the DHCP server. With the
exception of the default VLAN for which the DHCP server is enabled, this is the
default setting.
Page 59 / 414
LAN Configuration
59
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Enable DHCP Server
Select the
Enable DHCP Server
radio button to enable the wireless VPN firewall
to function as a Dynamic Host Configuration Protocol (DHCP) server, providing
TCP/IP configuration for all computers connected to the VLAN. (For the default
VLAN, the DHCP server is enabled by default.) Enter the following settings:
Domain Name
This setting is optional. Enter the domain name of the
wireless VPN firewall.
Start IP Address
Enter the start IP address. This address specifies the first of
the contiguous addresses in the IP address pool. Any new
DHCP client joining the LAN is assigned an IP address
between this address and the end IP address. For the default
VLAN, the default start IP address is 192.168.1.100.
End IP Address
Enter the end IP address. This address specifies the last of
the contiguous addresses in the IP address pool. Any new
DHCP client joining the LAN is assigned an IP address
between the start IP address and this IP address. For the
default VLAN, the default end IP address is 192.168.1.254.
The start and end DHCP IP addresses should be in the same
network
as the LAN IP address of the wireless VPN firewall
(that is, the IP address in the IP Setup section as described
earlier in this table).
Primary DNS
Server
This setting is optional. If an IP address is specified, the
wireless VPN firewall provides this address as the primary
DNS server IP address. If no address is specified, the
wireless VPN firewall uses the VLAN IP address as the
primary DNS server IP address.
Secondary DNS
Server
This setting is optional. If an IP address is specified, the
wireless VPN firewall provides this address as the secondary
DNS server IP address.
WINS Server
This setting is optional. Enter a WINS server IP address to
specify the Windows NetBIOS server, if one is present in your
network.
Lease Time
Enter a lease time. This specifies the duration for which IP
addresses are leased to clients.
DHCP Relay
To use the wireless VPN firewall as a DHCP relay agent for a DHCP server
somewhere else in your network, select the
DHCP Relay
radio button. Enter the
following setting:
Relay Gateway
The IP address of the DHCP server for which the wireless
VPN firewall serves as a relay.
Table 10.
Add VLAN Profile screen settings (continued)
Setting
Description
Page 60 / 414
LAN Configuration
60
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
4.
Click
Apply
to save your settings.
Note:
Once you have completed the LAN setup, all outbound traffic is
allowed and all inbound traffic is discarded except responses to
requests from the LAN side. For information about how to change
these default traffic rules, see
Chapter 5, Firewall Protection
.
Enable LDAP
information
To enable the DHCP server to provide Lightweight Directory Access Protocol
(LDAP) server information, select the
Enable LDAP information
check box.
Enter the following settings.
LDAP Server
The IP address or name of the LDAP server.
Search Base
The search objects that specify the location in the directory
tree from which the LDAP search begins. You can specify
multiple search objects, separated by commas. The search
objects include:
• CN (for common name)
• OU (for organizational unit)
• O (for organization)
• C (for country)
• DC (for domain)
For example, to search the Netgear.net domain for all last
names of Johnson, you would enter:
cn=Johnson,dc=Netgear,dc=net
Port
The port number for the LDAP server. The default setting is 0
(zero).
DNS Proxy
Enable DNS Proxy
This setting is optional. To enable the wireless VPN firewall to provide a LAN IP
address for DNS address name resolution, select the
Enable DNS Proxy
check
box. This setting is disabled by default.
Note:
When the DNS proxy option is disabled for a VLAN, all DHCP clients
receive the DNS IP addresses of the ISP but without the DNS proxy IP address.
Inter VLAN Routing
Enable Inter VLAN
Routing
This setting is optional. To ensure that traffic is routed only to VLANs for which
inter-VLAN routing is enabled, select the
Enable Inter VLAN Routing
check box.
This setting is disabled by default. When the Enable Inter VLAN Routing check
box is not selected, traffic from this VLAN is not routed to other VLANs, and traffic
from other VLANs is not routed to this VLAN.
Table 10.
Add VLAN Profile screen settings (continued)
Setting
Description

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top