Page 26 / 238
Scroll up to view Page 21 - 25
Reference Manual for the ProSafe VPN Firewall 25 with 4 Gigabit LAN and Dual WAN Ports
2-8
Introduction
202-10085-01, March 2005
Figure 2-2:
FVS124G Rear Panel
Viewed from left to right, the rear panel contains the following elements:
The Router’s IP Address, Login Name, and Password
Check the label on the bottom of the FVS124G’s enclosure if you forget the following factory
default information:
•
IP Address:
to reach the Web-based GUI from the LAN
•
User name:
admin
•
Password:
password
Table 2-2.
FVS124G rear panel
Item
Description
Factory Defaults
Button
Factory Defaults reset push button (see
“Default Factory Settings” on page 2-10
for the
factory defaults).
LAN Ports
4-port RJ-45 10/100/1000 Mbps Fast Ethernet Switch, N-way automatic speed
negotiation, auto MDI/MDIX.
WAN Ports
Two RJ-45 WAN ports, N-way automatic speed negotiation, Auto MDI/MDIX.
AC Power
Adapter
Connection
12 VDC, 1.2A
Factory
Defaults
LAN
4
3
2
1
WAN2
WAN1
12VDC 1.2A
AC Power
Adapter
Factory
Defaults
Button
Connection
WAN2 Port
WAN1 Port
LAN Ports
Page 27 / 238
Reference Manual for the ProSafe VPN Firewall 25 with 4 Gigabit LAN and Dual WAN Ports
Introduction
2-9
202-10085-01, March 2005
Figure 2-3:
FVS124G Bottom Label
Logging into the Router
To log into the FVS124G once it is connected,
1.
Open a Web browser.
2.
Enter
as the URL.
3.
Once you get the login screen (
Figure 2-4
), enter the following information:
•
admin
for User Name
•
password
for Password
LAN IP Address
User Name
Password
Page 28 / 238
Reference Manual for the ProSafe VPN Firewall 25 with 4 Gigabit LAN and Dual WAN Ports
2-10
Introduction
202-10085-01, March 2005
Figure 2-4:
Login screen on the Web browser
Note:
Read-only access is provided by logging in as username
guest
and default password
password
.
Default Factory Settings
When you first receive your FVS124G, the default factory settings will be set as shown in
Table 2-1
below. You can restore these defaults with the Factory Defaults restore switch on the
front panel — see
“The Router’s Front Panel” on page 2-6
.
•
Pressing this switch until the TEST LED blinks (approximately 10 seconds) causes the
firewall to restore all factory default settings and reboot.
•
A shorter press and release causes the firewall to merely reboot.
Page 29 / 238
Reference Manual for the ProSafe VPN Firewall 25 with 4 Gigabit LAN and Dual WAN Ports
Introduction
2-11
202-10085-01, March 2005
NETGEAR Related Products
NETGEAR products related to the FVS124G ProSafe VPN Firewall 25 with 4 Gigabit LAN and
Dual WAN Ports are as follows:
•
FA311 10/100 PCI Adapter
•
FA511 10/100 32-bit CardBus Adapter
•
GA311 10/100/1000 PCI Adapter
•
FVL328 ProSafe VPN Firewall
•
FVS318 ProSafe VPN Firewall 8
•
FVS338 ProSafe VPN Firewall 50
•
FVX538 ProSafe VPN Firewall 200
•
FWG114P ProSafe 802.11g Wireless Firewall with USB Print Server
•
NMS100 ProSafe Network Management System
•
VPN01L and VPN05L ProSafe VPN Client Software
•
WG302 ProSafe 802.11g Access Point
Table 2-1.
Factory Default Settings
Feature
Default
User Name (case sensitive)
admin
Password (case sensitive)
password
Built-in DHCP server
DHCP server is enabled, issues addresses in the
default subnet
IP Configuration
Subnet Mask: 255.255.255.0
Gateway: 0.0.0.0
Time Zone
GMT
Time Zone Adjust for Daylight Saving TIme
Enabled
SNMP
Disabled
Page 30 / 238
Reference Manual for the ProSafe VPN Firewall 25 with 4 Gigabit LAN and Dual WAN Ports
2-12
Introduction
202-10085-01, March 2005
19216811.live