Page 186 / 234 Scroll up to view Page 181 - 185
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
F-4
NETGEAR VPN Configuration FVS318 or FVM318 to FVL328
May 2004, 202-10030-02
Choose a subnet from local address from the Tunnel can access
pull-down menu.
Type the starting LAN IP Address of Gateway B (
172.23.9.1
in our example) in the Local
IP Remote LAN Start IP Address field.
Type the finishing LAN IP Address of Gateway B (
0.0.0.0
in our example) in the Local IP
Remote LAN Finish IP Address field.
Type the LAN Subnet Mask of Gateway B (
255.255.255.0
in our example) in the Remote
LAN IP Subnetmask field.
Type the WAN IP address (
22.23.24.25
in our example) of Gateway B in the Remote
WAN IP or FQDN field.
Figure F-4:
Figure 4 – NETGEAR FVS318 VPN Settings (part 2) – Main Mode
From the Secure Association drop-down box, select Main Mode.
Next to Perfect Forward Secrecy, select the Enabled radio button.
From the Encryption Protocol drop-down box, select 3DES.
In the PreShared Key box, type a unique text string to be used as the shared key between
Gateway A and Gateway B.
In this example we used
hr5xb84l6aa9r6
. You must make
sure the key is the same for both gateways.
In the Key Life box, enter in 3600 seconds.
In the IKE Life Time, enter 28800 seconds.
Check the NETBIOS Enable box if you wish to pass NetBIOS traffic over the VPN
tunnel, allowing functions such as Microsoft Network Neighborhood browsing.
3.
Click the Apply button in the lower center of the screen to save all changes. This will return
you to the VPN Settings screen.
Page 187 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
NETGEAR VPN Configuration FVS318 or FVM318 to FVL328
F-5
May 2004, 202-10030-02
Figure F-5:
NETGEAR FVS318 VPN Settings After Inputting Configuration Info
4.
When the screen returns to the VPN Settings, make sure the Enable check box is selected.
Step-By-Step Configuration of FVL328 Gateway B
1.
Log in to the NETGEAR FVL328 labeled Gateway B as in the illustration.
Out of the box, the FVL328 is set for its default LAN address of
with its
default user name of
admin
and default password of
password
. For this example we will
assume you have set the local LAN address as 172.23.9.1 for Gateway B and have set your
own user name and password.
2.
Click the IKE Policies link under the VPN category link on the left side of the Settings
management GUI. This will open the IKE Policies Menu. Click Add. This will open a new
screen titled IKE Policy Configuration.
Page 188 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
F-6
NETGEAR VPN Configuration FVS318 or FVM318 to FVL328
May 2004, 202-10030-02
Figure F-6:
NETGEAR FVL328 IKE Policy Configuration – Part 1
Enter an appropriate name for the policy in the Policy Name field. This name is not
supplied to the remote VPN Endpoint. It is used to help you manage the IKE policies. In
our example we have used FVS318 as the Policy Name. In the Policy Name field type
FVS318
.
From the Direction/Type drop-down box, select Both Directions.
From the Exchange Mode drop-down box, select Main Mode.
From the Local Identity drop-down box, select WAN IP Address (WAN IP address will
automatically be populated into the Local Identity Data field after policy is applied).
From the Remote Identity drop-down box, select Remote WAN IP (WAN IP address will
automatically be populated into the Local Identity Data field after policy is applied).
Page 189 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
NETGEAR VPN Configuration FVS318 or FVM318 to FVL328
F-7
May 2004, 202-10030-02
Figure F-7:
NETGEAR FVL328 IKE Policy Configuration – Part 2
From the Encryption Algorithm drop-down box, select 3DES.
From the Authentication Algorithm drop-down box, select MD5.
From the Authentication Method radio button, select Pre-shared Key.
In the Pre-Shared Key field, type
hr5xb84l6aa9r6
. You must make sure the key is the
same for both gateways.
From the Diffie-Hellman (DH) Group drop-down box, select Group 1 (768 Bit).
In the SA Life Time field, type 28800.
3.
Click the Apply Button. This will bring you back to the IKE Policies Menu.
Figure F-8:
NETGEAR FVL328 IKE Policies (Post Configuration)
The FVS318
IKE Policy is now displayed in the IKE Policies page.
4.
Click the VPN Policies link under the VPN category link on the left side of the Settings
management GUI. This will take you to the VPN Policies Menu page. Click Add Auto Policy.
This will open a new screen titled VPN – Auto Policy.
Page 190 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
F-8
NETGEAR VPN Configuration FVS318 or FVM318 to FVL328
May 2004, 202-10030-02
Figure F-9:
NETGEAR FVL328 VPN – Auto Policy (part 1)
Enter a unique name to identify this policy. This name is not supplied to the remote VPN
endpoint. In our example we have used “to318” as the Policy Name. In the Policy Name
field type
to318
.
From the IKE policy drop-down box, select the IKE Policy that was set up in the earlier
step – this being the FVS318 IKE Policy.
From the Remote VPN Endpoint Address Type drop-down box, select IP Address.
Type the WAN IP Address of Gateway A (
14.15.16.17
in our example) in the
Remote
VPN Endpoint Address Data field.
Type
300
in the SA Life Time (Seconds) field.
Type
0
in the SA Life Time (Kbytes) field.
Check the IPSec PFS check box.
From the PFS Key Group drop-down box, select Group 2 (1024 Bit).
From the Traffic Selector Local IP drop-down box, select Subnet address.
Type the starting LAN IP Address of Gateway B (
172.23.9.1
in our example) in the Local
IP Start IP Address field.
Type the finishing LAN IP Address of Gateway B (
0.0.0.0
in our example) in the Local IP
Finish IP Address field.
Type the LAN Subnet Mask of Gateway B (
255.255.255.0
in our example) in the Local IP
Subnet Mask field.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top