1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FVL328
    5. /
  5. 32
Page 156 / 234 Scroll up to view Page 151 - 155
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
C-6
Preparing Your Network
May 2004, 202-10030-02
If you need to install a new adapter, follow these steps:
a.
Click the Add button.
b.
Select Adapter, and then click Add.
c.
Select the manufacturer and model of your Ethernet adapter, and then click OK.
If you need TCP/IP:
a.
Click the Add button.
b.
Select Protocol, and then click Add.
c.
Select Microsoft.
d.
Select TCP/IP, and then click OK.
If you need Client for Microsoft Networks:
a.
Click the Add button.
b.
Select Client, and then click Add.
c.
Select Microsoft.
d.
Select Client for Microsoft Networks, and then click OK.
3.
Restart your PC for the changes to take effect.
Enabling DHCP to Automatically Configure TCP/IP Settings
After the TCP/IP protocol components are installed, each PC must be assigned specific
information about itself and resources that are available on its network. The simplest way to
configure this information is to allow the PC to obtain the information from the internal DHCP
server of the FVL328 Firewall. To use DHCP with the recommended default addresses, follow
these steps:
1.
Connect all computers to the firewall, then restart the firewall and allow it to boot.
2.
On each attached PC, open the Network control panel (refer to the previous section) and select
the Configuration tab.
Note:
It is not necessary to remove any other network components shown in the
Network window in order to install the adapter, TCP/IP, or Client for Microsoft
Networks.
Page 157 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
Preparing Your Network
C-7
May 2004, 202-10030-02
3.
From the components list, select TCP/IP->(your Ethernet adapter) and click Properties.
4.
In the IP Address tab, select “Obtain an IP address automatically”.
5.
Select the Gateway tab.
6.
If any gateways are shown, remove them.
7.
Click OK.
8.
Restart the PC.
Repeat steps 2 through 8 for each PC on your network.
Selecting Windows’ Internet Access Method
1.
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2.
Double-click the Internet Options icon.
3.
Select “I want to set up my Internet connection manually” or “I want to connect through a
Local Area Network” and click Next.
4.
Select “I want to connect through a Local Area Network” and click Next.
5.
Uncheck all boxes in the LAN Internet Configuration screen and click Next.
6.
Proceed to the end of the Wizard.
Verifying TCP/IP Properties
After your PC is configured and has rebooted, you can check the TCP/IP configuration using the
utility
winipcfg.exe
:
1.
On the Windows taskbar, click the Start button, and then click Run.
2.
Type
winipcfg
, and then click OK.
The IP Configuration window opens, which lists (among other things), your IP address, subnet
mask, and default gateway.
3.
From the drop-down box, select your Ethernet adapter.
The window is updated to show your settings, which should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends:
•
The IP address is between 192.168.0.2 and 192.168.0.254
•
The subnet mask is 255.255.255.0
Page 158 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
C-8
Preparing Your Network
May 2004, 202-10030-02
•
The default gateway is 192.168.0.1
Configuring Windows NT, 2000 or XP for IP Networking
As part of the PC preparation process, you need to manually install and configure TCP/IP on each
networked PC. Before starting, locate your Windows CD; you may need to insert it during the
TCP/IP installation process.
Installing or Verifying Windows Networking Components
To install or verify the necessary components for IP networking:
1.
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2.
Double-click the Network and Dialup Connections icon.
3.
If an Ethernet adapter is present in your PC, you should see an entry for Local Area
Connection. Double-click that entry.
4.
Select Properties.
5.
Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6.
Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7.
Click OK and close all Network and Dialup Connections windows.
8.
Make sure your PC is connected to the firewall, then reboot your PC.
Verifying TCP/IP Properties
To check your PC’s TCP/IP configuration:
1.
On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2.
Type
cmd
and then click OK.
A command window opens
3.
Type
ipconfig /all
Page 159 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
Preparing Your Network
C-9
May 2004, 202-10030-02
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends:
•
The IP address is between 192.168.0.2 and 192.168.0.254
•
The subnet mask is 255.255.255.0
•
The default gateway is 192.168.0.1
4.
Type
exit
Configuring the Macintosh for TCP/IP Networking
Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On
each networked Macintosh, you will need to configure TCP/IP to use DHCP.
MacOS 8.6 or 9.x
1.
From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens:
2.
From the “Connect via” box, select your Macintosh’s Ethernet interface.
3.
From the “Configure” box, select Using DHCP Server.
You can leave the DHCP Client ID box empty.
4.
Close the TCP/IP Control Panel.
Page 160 / 234
Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual Revision 2
C-10
Preparing Your Network
May 2004, 202-10030-02
5.
Repeat this for each Macintosh on your network.
MacOS X
1.
From the Apple menu, choose System Preferences, then Network.
2.
If not already selected, select Built-in Ethernet in the Configure list.
3.
If not already selected, Select Using DHCP in the TCP/IP tab.
4.
Click Save.
Verifying TCP/IP Properties for Macintosh Computers
After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by
returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
The panel is updated to show your settings, which should match the values below if you are using
the default TCP/IP settings that NETGEAR recommends:
•
The IP Address is between 192.168.0.2 and 192.168.0.254
•
The Subnet mask is 255.255.255.0
•
The Router address is 192.168.0.1
If you do not see these values, you may need to restart your Macintosh or you may need to switch
the “Configure” setting to a different option, then back again to “Using DHCP Server”.

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top