1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. DGND3700v2
    5. /
  5. 19
Page 91 / 185 Scroll up to view Page 86 - 90
Virtual Private Networking
91
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700
The following worksheet identifies the parameters used in this procedure. For a blank
worksheet, see
Plan a VPN
on page 88.
Table 17.
VPN tunnel configuration worksheet
Parameter
Value to Be Entered
Field Selection
Connection Name
RoadWarrior
N/A
Pre-Shared Key
12345678
N/A
Secure Association
N/A
Main Mode
Manual Keys
Perfect Forward secrecy
N/A
Enabled
Disabled
Encryption Protocol
N/A
DES
3DES
Authentication Protocol
N/A
MD5
SHA-1
Diffie-Hellman (DH) Group
N/A
Group 1
Group 2
Key Life in seconds
28800 (8 hours)
N/A
IKE Life Time in seconds
3600 (1 hour)
N/A
VPN Endpoint
Local IPSecID
LAN IP Address
Subnet Mask
FQDN or Gateway
IP (WAN IP
Address)
Client
toGateway
N/A
N/A
Dynamic
Gateway
toClient
192.168.3.1
255.255.255.0
22.23.24.25
To configure a client-to-gateway VPN tunnel using the VPN Wizard:
1.
Log in to the wireless modem router. On the main menu under Advanced - VPN, select
VPN Wizard
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 92 / 185
Virtual Private Networking
92
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700
2.
Click
Next
to proceed.
3.
Fill in the
Connection Name
and
pre-shared key
fields.
The connection name is for convenience and does not affect how the VPN tunnel
functions.
4.
Select the radio button for the type of target end point, and click
Next
.
5.
Enter the remote IP address, and click
Next
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 93 / 185
Virtual Private Networking
93
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700
The Summary screen displays:
Note:
To view the VPNC-recommended authentication and encryption
settings used by the VPN Wizard, click the
here
link.
6.
Click
Done
on the Summary screen. The VPN Policies screen displays, showing that the
new tunnel is enabled:
To view or modify the tunnel settings, select its radio button and click
Edit
.
Note:
See
Use Auto Policy to Configure VPN Tunnels
on page 112 for
information about how to enable the IKE keep-alive capability on an existing
VPN tunnel.
Step 2: Configure the NETGEAR ProSafe VPN Client
This section describes how to configure the NETGEAR ProSafe VPN client on a remote PC.
These instructions assume that the PC running the client has a dynamically assigned IP
address.
Downloaded from
www.Manualslib.com
manuals search engine
Page 94 / 185
Virtual Private Networking
94
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700
The PC has to have the NETGEAR ProSafe VPN Client program installed, which supports
IPSec. Go to the NETGEAR website (
) for information about how to
purchase the NETGEAR ProSafe VPN client.
Note:
Before installing the NETGEAR ProSafe VPN Client software, be
sure to turn off any virus protection or firewall software you might be
running on your PC. You might need to insert your Windows CD to
complete the installation.
To configure the NETGEAR ProSafe VPN client:
1.
Install the NETGEAR ProSafe VPN client on the remote PC, and then reboot.
a.
Install the IPSec component. You might have the option to install either the VPN
adapter or the IPSec component or both. The VPN adapter is not necessary.
If you do not have a modem or dial-up adapter installed in your PC, you might see the
warning message stating, “The NETGEAR ProSafe VPN Component requires at least
one dial-up adapter be installed.” You can disregard this message.
b.
Reboot the remote PC.
The ProSafe icon (
) is in the system tray.
c.
Double-click the ProSafe icon to open the Security Policy Editor.
2.
Add a new connection.
a.
Run the NETGEAR ProSafe Security Policy Editor program, and, using
Table 17
on
page 91, create a VPN connection.
b.
From the Edit menu of the Security Policy Editor, select
Add
, and then click
Connection
.
A New Connection listing appears in the list of policies.
Downloaded from
www.Manualslib.com
manuals search engine
Page 95 / 185
Virtual Private Networking
95
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700
c.
Rename the new connection so that it matches the
Connection Name
field in the
VPN Settings screen of the wireless modem router on LAN A. Choose connection
names that make sense to the people using and administering the VPN.
Note:
In this example, the connection name used on the client side of the
VPN tunnel is togw_a, and it does not have to match the
RoadWarrior connection name used on the gateway side of the VPN
tunnel because connection names are irrelevant to how the VPN
tunnel functions.
d.
Enter the following settings:
•
Connection Security
. Select
Secure
.
•
ID Type
. Select
IP Subnet
.
•
Subnet
. In this example, type
192.168.3.1
as the network address of the wireless
modem router.
•
Mask
. Enter
255.255.255.0
as the LAN subnet mask of the wireless modem
router.
•
Protocol
. Select
All
to allow all traffic through the VPN tunnel.
e.
Select the
Connect using Secure Gateway Tunnel
check box.
f.
In the
ID Type
drop-down list, select
IP Address
.
g.
Enter the public WAN IP address of the wireless modem router in the field directly
below the
ID Type
drop-down list. In this example,
22.23.24.25
is used.
The resulting connection settings are shown in the figure that follows.
3.
Configure the security policy in the NETGEAR ProSafe VPN Client software:
a.
In the Network Security Policy list, expand the new connection by double-clicking its
name or clicking the
+
symbol. My Identity and Security Policy subheadings appear
below the connection name.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top