Page 71 / 132 Scroll up to view Page 66 - 70
Reference Manual for the Model DG632 ADSL Modem Router
Using Router Mode
6-19
4.
Click Apply.
Configuring Advanced Settings
The DG632 ADSL Modem Router provides a variety of advanced features, such as:
Setting up a Demilitarized Zone (DMZ) Server
Connecting Automatically, as Required
Disabling Port Scan and DOS Protection
Responding to a Ping on the Internet WAN Port
MTU Size
The flexibility of configuring your LAN TCP/IP settings
Using the Router as a DHCP Server
Configuring Static Routes
These features are discussed below.
Setting Up A Default DMZ Server
The Default DMZ Server feature is helpful when using some online games and videoconferencing
applications that are incompatible with NAT. The modem is programmed to recognize some of
these applications and to work properly with them, but there are other applications that may not
function well. In some cases, one local computer can run the application properly if that
computer’s IP address is entered as the Default DMZ Server.
Incoming traffic from the Internet is normally discarded by the modem unless the traffic is a
response to one of your local computers or a service that you have configured in the Ports menu.
Instead of discarding this traffic, you can have it forwarded to one computer on your network. This
computer is called the Default DMZ Server.
Note:
For security reasons, you should avoid using the Default DMZ Server feature.
When a computer is designated as the Default DMZ Server, it loses much of the
protection of the firewall, and is exposed to many exploits from the Internet. If
compromised, the computer can be used to attack your network.
Page 72 / 132
Reference Manual for the Model DG632 ADSL Modem Router
6-20
Using Router Mode
How to Configure a Default DMZ Server
To assign a computer or server to be a Default DMZ server, follow these steps:
1.
Log in to the modem at its default LAN address of http://192.168.0.1 with its default User
Name of
admin
, default password of
password
, or using whatever Password and LAN
address you have chosen for the modem.
2.
From the Main Menu, under Advanced, click the WAN Setup link to view the page shown in
Figure 6-14
Figure 6-14:
WAN Setup Page
3.
Click Default DMZ Server.
4.
Type the IP address for that server.
5.
Click Apply to save your changes.
Connect Automatically, as Required
Normally, this option should be Enabled, so that an Internet connection will be made
automatically, whenever Internet-bound traffic is detected. If this causes high connection costs,
you can disable this setting.
If disabled, you must connect manually, using the sub-screen accessed from the "Connection
Status" button on the Status screen.
If you have an "Always on" connection, this setting has no effect.
Page 73 / 132
Reference Manual for the Model DG632 ADSL Modem Router
Using Router Mode
6-21
Disable Port Scan and DOS Protection
The Firewall protects your LAN against Port Scans and Denial of Service (DOS) attacks. This
should be disabled only in special circumstances.
Respond to Ping on Internet WAN Port
If you want the modem to respond to a 'ping' from the Internet, select the ‘Respond to Ping on
Internet WAN Port’ check box. This should only be used as a diagnostic tool, since it allows your
modem to be discovered. Do not select this box unless you have a specific reason to do so.
MTU Size
The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 Bytes, or
1492 Bytes for PPPoE connections. For some ISPs you may need to reduce the MTU. But this is
rarely required, and should not be done unless you are sure it is necessary for your ISP connection.
Configuring LAN IP Settings
The LAN IP Setup menu allows configuration of LAN IP services such as DHCP and RIP. These
features can be found under the Advanced heading in the Main Menu of the browser interface.
The modem is shipped preconfigured to use private IP addresses on the LAN side, and to act as a
DHCP server. The modem’s default LAN IP configuration is:
LAN IP addresses—192.168.0.1
Subnet mask—255.255.255.0
Page 74 / 132
Reference Manual for the Model DG632 ADSL Modem Router
6-22
Using Router Mode
These addresses are part of the Internet Engineering Task Force (IETF)-designated private address
range for use in private networks, and should be suitable in most applications. If your network has
a requirement to use a different IP addressing scheme, you can make those changes in this menu.
Figure 6-15:
LAN IP Setup Menu
The LAN TCP/IP Setup parameters are:
IP Address
This is the LAN IP address of the modem.
IP Subnet Mask
This is the LAN Subnet Mask of the modem. Combined with the IP address, the IP Subnet
Mask allows a device to know which other addresses are local to it, and which must be reached
through a gateway or modem.
RIP Direction
RIP (Router Information Protocol) allows a modem to exchange routing information with
other routers. The RIP Direction selection controls how the Modem sends and receives RIP
packets. Both is the default.
When set to Both or Out Only, the modem will broadcast its routing table periodically.
When set to Both or In Only, it will incorporate the RIP information that it receives.
When set to None, it will not send any RIP packets and will ignore any RIP packets
received.
Page 75 / 132
Reference Manual for the Model DG632 ADSL Modem Router
Using Router Mode
6-23
RIP Version
This controls the format and the broadcasting method of the RIP packets that the modem
sends. It recognizes both formats when receiving. By default, this is set for RIP-1.
RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you
have an unusual network setup.
RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2
format.
RIP-2B uses subnet broadcasting.
RIP-2M uses multicasting.
DHCP
By default, the modem will function as a DHCP (Dynamic Host Configuration Protocol) server,
allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to
the modem's LAN. The assigned default gateway address is the LAN address of the router. IP
addresses will be assigned to the attached PCs from a pool of addresses specified in this menu.
Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.
For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. See
“IP
Configuration by DHCP“ on page -10
for an explanation of DHCP and information about how to
assign IP addresses for your network.
Use Router as DHCP server
If another device on your network will be the DHCP server, or if you will manually configure the
network settings of all of your computers, clear the ‘Use router as DHCP server’ check box.
Otherwise, leave it selected.
Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP
Address. These addresses should be part of the same IP address subnet as the router’s LAN IP
address. Using the default addressing scheme, you should define a range between 192.168.0.2 and
192.168.0.254, although you may want to save part of the range for devices with fixed addresses.
The router will deliver the following parameters to any LAN device that requests DHCP:
Note:
If you change the LAN IP address of the modem while connected through the
browser, you will be disconnected. You must then open a new connection to the new IP
address and log in again.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top