YML9WMAXXN

ADSL2+ Wireless N300 Modem Router with VoIP User Guide

www.netcomm.com.au

21

NetComm Gateway

TM

Series - ADSL2+ Wireless N300 Modem Router with VoIP

5:

Click

Next

. The following screen appears.

Enable NAT

If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu will be displayed after reboot.

The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side (i.e. the

LAN side is using a public IP), this checkbox should be de-selected. When the system comes back after reboot, the NAT submenu will be

no longer available.

Enable Fullcone NAT

This option becomes available when NAT is enabled.

Known as one-to-one NAT, all requests from the same internal IP address and port

are mapped to the same external IP address and port. An external host can send a packet to the internal host, by sending a packet to the

mapped external address.

Enable Firewall

If the firewall checkbox is selected, the Security submenu will be displayed after system reboot. The user can then configure firewall features

after the system comes up. If firewall is not used, this checkbox should be de-selected to free up system resources for better performance.

When system comes back after reboot, the Security submenu will be gone.

6:

Click

Next

to display the following screen.

The Device Setup screen allows the user to configure the LAN interface IP address and DHCP server. If the user would like this router to

assign dynamic IP addresses, DNS server and default gateway to other LAN devices. Select the button Enable DHCP server on the LAN to

enter the starting IP address and end IP address and DHCP lease time.

The Device Setup screen allows the user to configure the LAN interface IP address and DHCP server. If the user would like this router

to assign dynamic IP addresses, DNS server and default gateway to other LAN devices. Select the radio box

Enable DHCP server on

the LAN

to enter the starting IP address and end IP address and DHCP lease time. This configures the router to automatically assign IP

addresses, default gateway address and DNS server addresses to each of your PCs.

Select

Enable DHCP Server Relay

(if required), and enter the DHCP Server IP Address. This allows the router to relay the DHCP packets

from the remote DHCP server. The remote DHCP server will provide the IP address.

NOTE:

If NAT is enabled, Enable DHCP Server Relay won’t display.

To configure a secondary IP address for the LAN port, click the box as shown below.

ADSL2+ Wireless N300 Modem Router with VoIP User Guide

YML9WMAXXN

22

www.netcomm.com.au

7:

Click

Next

to continue. To enable the wireless function, select the radio button (as shown), input a new SSID (if desired) and click

Next

.

The following screen will be displayed.

8:

The WAN Setup-Summary screen presents the entire configuration summary. After clicking Save/Reboot, the router will save the

configuration to flash memory and reboot. Click Back if you wish to modify the settings. The Web UI will not respond until the

system is brought up again. After the system is up, the Web UI will refresh to the Home screen automatically. The router is ready for

operation when the LED indicators display as described in Section 1.3

4.2.4

Bridging

Follow Steps 1 through to 3 of Manual Quick Setup

4:

Select the Bridging radio button and click

Next

.

YML9WMAXXN

ADSL2+ Wireless N300 Modem Router with VoIP User Guide

www.netcomm.com.au

23

NetComm Gateway

TM

Series - ADSL2+ Wireless N300 Modem Router with VoIP

The following screen appears. To use the bridge service, tick the

Enable Bridge Service

checkbox and enter a service name (user defined).

5:

Click the

Next

button to continue. Enter the IP address for the LAN interface. The default IP address is 192.168.1.1. The LAN IP

interface in bridge operating mode is needed for local users to manage the router. Notice that there is no IP address for the WAN

interface in bridge mode, and technical support cannot access the router remotely.

6:

Click

Next

to continue. To enable the wireless function, select the radio button (as shown), input a new SSID (if desired) and click

Next

.

The following screen will be displayed.

7:

The WAN Setup-Summary screen presents the entire configuration summary. After clicking

Save/Reboot

, the router will save the

configuration to the flash memory, and reboot. Click

Back

if you wish to modify the settings. The Web UI will not respond until the

system is brought up again. After the system is up, the Web UI will refresh to the

Device Info

screen automatically.

ADSL2+ Wireless N300 Modem Router with VoIP User Guide

YML9WMAXXN

24

www.netcomm.com.au

Select

Basic Info

from the main menu to display Summary information as below.

NOTE:

The figure above shows the summary screen with an ADSL signal.

For more information on ADSL Quick Setup, please refer to Chapter 4- Quick Setup

Voice