1. Home
    2. /
  2. Manuals
    3. /
  3. NetComm
    4. /
  4. NB4
    5. /
  5. 2
Page 6 / 77 Scroll up to view Page 1 - 5
NB4 User Guide
YML733Rev1
6
www.netcomm.com.au
Package Contents
Package Contents
Package Contents
Package Contents
Package Contents
The following items should be contained in your Ethernet/USB ADSL Modem Package:
■
NB4 ADSL 4-port Modem Router
■
CD-ROM containing Manual
■
RJ45 Ethernet Cable (CAT5 UTP Straight-Through)
■
RJ11 ADSL Cable (Standard telephone cable)
■
Power Adapter
■
Quick Installation Guide and Package Contents Note
Check the contents of your package and, if any parts are missing or damaged, please contact
your Dealer.
Page 7 / 77
YML733 Rev1
NB4 User Guide
www.netcomm.com.au
7
Quick Start
Quick Start
Quick Start
Quick Start
Quick Start
This Quick Start provides basic instructions for connecting the NB4 A
DSL Modem Router
to a
computer and to the Internet.
■
Step 1
- describes setting up the hardware.
■
Step 2
- shows you how to configure basic settings on the
NB4 ADSL Modem Router
to get
your computer connected to the Internet.
■
Step 3
- describes how to configure Internet properties on your computer(s).
This Quick Start Guide assumes that you have already established an ADSL service with your
Internet service provider (ISP). These instructions provide a basic configuration that should be
compatible with your home or small office setup. Refer to the Advanced Features section for
additional configuration instructions.
NOTE:
NetComm Technical Support for this product only covers the basic installation
and features outlined in the Quick Start section.
For detailed information
regarding the advanced features of this product, please refer to the configuring
sections.
The NetComm
NB4 ADSL Modem Router
can be connected directly to your computer via an
Ethernet interface.
If your computer has a network card (NIC) but isn’t connected to a network hub
or switch, or another computer, then connect the NB4 to the network port of your PC.
Warning:
Warning:
Warning:
Warning:
Warning:
Before you begin, turn the power off for all devices. These include
Before you begin, turn the power off for all devices. These include
Before you begin, turn the power off for all devices. These include
Before you begin, turn the power off for all devices. These include
Before you begin, turn the power off for all devices. These include
your computer(s) and the NB4 ADSL Modem Router.
your computer(s) and the NB4 ADSL Modem Router.
your computer(s) and the NB4 ADSL Modem Router.
your computer(s) and the NB4 ADSL Modem Router.
your computer(s) and the NB4 ADSL Modem Router.
Page 8 / 77
NB4 User Guide
YML733Rev1
8
www.netcomm.com.au
Step 1 - Hardware Installation
To connect
your modem, follow the step by step instructions below:
1.
Connecting the ADSL cable.
Connect one end of the provided phone cable to the port labeled DSL on the Rear Panel of
the device. Connect the other end to your wall phone jack.
2.
Connecting the Ethernet
cable.
Connect one end of the ethernet cable to the network port on your PC and the other end of
the cable to the ethernet port of the
NB4 ADSL Modem Router
.
3.
Attach the power connector.
Connect the AC power adapter to the Power connector on the back of the device and plug
in the adapter to a wall outlet or power strip.
Switch the power on to the NB4.
4.
Power up your systems.
Turn on and boot up your computer.
After completing the above, refer to the appropriate operating system section to configure
your computer.
NOTE:
At this stage, if your ADSL line is active the ADSL Light should stay perma-
nently ON - if it is blinking, then an ADSL Service has not been detected.
Page 9 / 77
YML733 Rev1
NB4 User Guide
www.netcomm.com.au
9
Step 2 - Modem Configuration
In Step 2, you log directly into the configuration page of
the
NB4 ADSL Modem Router
and
configure the basic settings for your Internet connection. Your ISP should provide you with the
necessary information to complete this step.
The settings that you most likely need to change to access the internet are grouped onto a single
Quick Configuration page.
To configure your
NB4 ADSL Modem Router
follow the steps below:
Note:
If your computer's Ethernet interface is not set to use DHCP or you have trouble
accessing/configuring your NB4, see instructions overleaf "Computer Hardware
Configuration".
1.
Insert the NetComm NB4 CD into your CD drive.
The
NB4 ADSL Modem Router
autorun
screen will appear.
Click on
Configure NB4.
(Alternatively, if the CD-Rom is not available, you can open a web browser and type
http://192.168.1.1 in the location bar to access the NB4's setup screen directly.)
2.
The logon page will be displayed. Enter the NB4’s username and password.
The default username
is
admin
.
The default password is
password
.
Click on
OK
.
3.
The Quick Start - login settings page will be displayed.
Page 10 / 77
NB4 User Guide
YML733Rev1
10
www.netcomm.com.au
4.
Under the User ID heading, enter the Username that your ISP has provided. In the
password field, enter the password that your ISP has given you.
5.
Leave the Protocol, VPI and VCI settings as default unless advised to change them by
your ISP.
6.
Click on the Connect button to test the settings.
7.
If the test was successful, then click "Save Settings". If it failed, please try again by clicking
on the "Connect" button a second time.
Also, check your settings to ensure they are
correct.
8.
You should now be able to access the Internet with a web browser, email client or other
Internet application.

Rate

4.5 / 5 based on 2 votes.

Popular NetComm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top