1. Home
    2. /
  2. Manuals
    3. /
  3. NetComm
    4. /
  4. 4G100W
    5. /
  5. 3
Page 11 / 57 Scroll up to view Page 6 - 10
www.netcommwireless.com
4G LTE WiFi Router
11
YMLN4G100W
Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless
networks nearby that can conflict with your wireless network and cause interference. Use the Site Survey capabilities found in the
Wireless Utility of your wireless adapter to locate any other wireless networks that are available (see your wireless adapter
’s user
manual), and switch your Router and computers to a channel as far away from other networks as possible.
Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from
neighbouring cordless phones or other wireless devices.
Hardware installation
1.
Insert your SIM card (until you hear a click) into the SIM slot. Please be careful to insert the SIM card with the correct
orientation by viewing the printed icon on the router housing.
2.
Connect the power adapter to the power socket on the back of the 4G100W 4G LTE WiFi Router.
3.
Plug the power adapter into your power point and switch on the power.
4.
Wait approximately 60 seconds for the 4G100W 4G LTE WiFi Router to power up.
Connecting via an Ethernet cable
1.
If you wish to connect a computer via Ethernet cable, connect the yellow Ethernet cable provided to one of the Ethernet
ports on the back of the 4G100W 4G LTE WiFi Router.
2.
Connect the other end of the Ethernet cable to your computer or to another Ethernet-enabled device such as a gaming
console, a TV or a home cinema system.
3.
Wait approximately 30 seconds for the connection to establish.
Connecting wirelessly
You can connect multiple WiFi
devices, including laptops, desktops, tablets and PDA’s to your
Router by following these two
basic steps.
1.
Ensure WiFi is enabled on your device (computer/laptop/smartphone).
2.
Scan for wireless networks in your area and connect to the network name shown on the included Wireless Security Card.
3.
When prompted for your wireless security settings, enter the Wireless security key shown on the included Wireless Security
Card.
4.
Wait approximately 30 seconds for the connection to establish.
5.
To connect additional devices via WiFi, repeat steps 1 through 4.
Page 12 / 57
12
4G LTE WiFi Router
www.netcommwireless.com
YMLN4G100W
Management Console
Management Console Login Procedure
For further device configuration, you can log in to the device’s management console via your web browser. T
he management
console is password protected to prevent unauthorized access to the configuration settings of your 4G100W 4G LTE WiFi Router.
To log in to the management console, view the status and make changes to your 4G100W 4G LTE WiFi Router, please follow the
steps below:
1.
Open your web browser (e.g. Internet Explorer/Firefox/Safari) and navigate to http://192.168.20.1
2.
Enter the username and password and click the Submit button. The default username and password
is “
admin
”
.
Note: If you forget the 4G100W 4G LTE WiFi Router username and password after changing it, holding the reset button for
over 10 seconds will restart the unit with the original factory default settings with the default username and password
returning to “admin”.
Figure 4 - Management Console Login
Page 13 / 57
www.netcommwireless.com
4G LTE WiFi Router
13
YMLN4G100W
Basic Status Overview
The basic status page provides basic system related information. It is shown after logging in to the 4G100W 4G LTE WiFi Router,
and can also be accessed by selecting Status from the menu tabs.
Figure 5 - Basic View
–
Status
The status page shows the Frequency, Signal Strength (dBm), Connection Status, Current Network Provider, Current APN and the
SIM Status.
Page 14 / 57
14
4G LTE WiFi Router
www.netcommwireless.com
YMLN4G100W
Wireless
Figure 6 - Basic View
–
Wireless
The wireless page allows you to configure basic WiFi settings for the 4G100W 4G LTE WiFi Router such as enabling/disabling the
WiFi functionality, changing the Wireless Network Name (SSID) or the Wireless Security key.
OPTION
DEFINITION
WiFi Network Name (SSID)
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your
wireless device so that you can easily connect your wireless clients to it. This field is case sensitive and can be
up to 32 characters long.
WiFi Password (Security key)
Enter your chosen Wireless Security key here. The default WPA2-PSK key is printed on the wireless security
card and on the Product ID on the bottom of the 4G100W 4G LTE WiFi Router. Please note that whilst the key
can be customized on this page, the key will revert to the default key if the 4G100W 4G LTE WiFi Router is
reset to factory default settings.
Table 9 - Basic View - WiFi Settings
Page 15 / 57
www.netcommwireless.com
4G LTE WiFi Router
15
YMLN4G100W
Internet
Figure 7 - Basic View
–
Internet
The Mobile Broadband Operation Mode can be configured on this page. Please see the table below for options allowed for the 3G
operation mode:
OPTION
DEFINITION
Automatically configure my
mobile broadband
When this option is selected the router will automatically detect the SIM card, enter the appropriate APN and
connect to the Mobile Broadband network. Do not select this option if your Mobile Broadband connection
requires a username and password.
Mobile Broadband
Use this option to enable or disable the Mobile broadband function on the router.
Click here if your service
requires a Username and
Password.
If your connection requires a username and password to authenticate the Mobile Broadband network
connection select this option. Enter the username and password into the small window that will appear and
press the Save button.
Custom APN (if required)
Enter an APN (Access Point Name) if the Auto Configuration option does not correctly identify your mobile
broadband service settings.
Country
Select the country that your Mobile Broadband provider operates in. By pressing the “Click here to choose an
APN” link, a list of Mobil
e Broadband providers will appear for the selected country for you to choose from.
SIM Status
The current status of the inserted SIM. If ‘SIM PIN’ is shown, enter the SIM PIN in the fields below.
PIN
Enter the SIM PIN here (if required).
Confirm PIN
Re-enter the SIM PIN here (if required).
Remember PIN
Select to remember the entered SIM PIN. This means you should not need to enter the pin again to be able to
use the inserted SIM.
Table 10 - Basic View - Internet Settings
You can also elect to use the
“
Automatically Configure my Mobile Broadband
”
option. This option attempts to automatically fill out
the correct APN from your SIM enabling you to connect to the most appropriate mobile broadband service. Please verify the APN
detected is correct by clicking on the Status tab. The current APN will be listed at the bottom of the page.
Alternatively, you can disable
the “
Auto
matically Configure my Mobile Broadband” option
and manually enter the APN you would like
to use.
If the
“
Auto
matically Configure my Mobile Broadband” option
does not correctly detect your APN and you are unsure of what to
enter manually, please contact your mobile broadband service provider for more information.

Rate

3.5 / 5 based on 2 votes.

Popular NetComm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top