1. Home
    2. /
  2. Manuals
    3. /
  3. MyTech
    4. /
  4. Facile
    5. /
  5. 16
Page 76 / 80 Scroll up to view Page 71 - 75
[ADSL]
The ADSL screen gives you information about how much data your router has transmitted or
received across the ADSL connection. Click on REFRESH to update the screen.
5. Troubleshooting
If the router is not function properly, first check this session for simple troubleshooting before
contacting your Internet service provider (ISP) for support.
5.1 Using LEDs to Diagnose Problems
The
LEDs
are useful aides for finding possible problem causes.
5.1.1 Power LED
The
PWR LED
on the front panel does not light up.
STEPS
CORRECTIVE ACTION
1
Make sure that the power adaptor is connected to the router and plugged in to an
appropriate power source. Use only the supplied power adaptor.
2
Check that the router and the power source are both turned on and the router is
receiving sufficient power.
3
Turn the router off and on.
4
If the error persists, you may have a hardware problem. In this case, you should contact
your vendor.
5.1.2 LAN LED
The
LAN LED
on the front panel does not light up.
75
STEPS
CORRECTIVE ACTION
1
Check the Ethernet cable connections between your router and the computer or hub.
2
Check for faulty Ethernet cables.
3
Make sure your computer’s Ethernet card is working properly.
4
If these steps fail to correct the problem, contact your local distributor for assistance.
Page 77 / 80
5.1.3 ADSL LED
The
ADSL LED
on the front panel does not light up.
STEPS
CORRECTIVE ACTION
1
Check the telephone wire and connections between the router ADSL port and the wall
jack.
2
Make sure that the telephone company has checked your phone line and set it up for
ADSL service.
3
Reset your ADSL line to reinitialize your link to the DSLAM.
4
If these steps fail to correct the problem, contact your local distributor for assistance.
5.2 Problems with the Web Interface
I cannot access the web Interface.
STEPS
CORRECTIVE ACTION
1
Make sure you are using the correct IP address of the router. Check the IP address of
the router.
2
Make sure that there is not a console session running.
3
Check that you have enabled web service access. If you have configured a secured
client IP address, your computer’s IP address must match it. Refer to the chapter on
remote management for details.
4
For WAN access, you must configure remote management to allow server access from
the WAN (or all).
5
Your computer’s and the router’s IP addresses must be on the same subnet for LAN
access.
6
If you changed the router’s LAN IP address, then enter the new one as the URL.
7
Remove any filters in LAN or WAN that block web service.
The web Interface does not display properly.
STEPS
CORRECTIVE ACTION
1
Make sure you are using Internet Explorer 5.0 and later versions.
2
Delete the temporary web files and log in again.
In Internet Explorer, click
Tools
,
Internet Options
and then click the
Delete Files ...
button.
When a
Delete Files
window displays, select
Delete all offline content
and click
OK
.
(Steps may vary depending on the version of your Internet browser.)
76
Page 78 / 80
5.3 Problems with the Login Username and Password
I forgot my login username and/or password.
STEPS
CORRECTIVE ACTION
1
If you have changed the password and have now forgotten it, you will need to upload
the default configuration file. This will erase all custom configurations and restore all of
the factory defaults including the password.
2
Press the
DEFAULT
button for five seconds, and then release it. When the
ADSL
LED
begins to blink, the defaults have been restored and the router restarts.
3
The default username is “
admin
”. The default password is “
trendchip
”. The
Password
and
Username
fields are case-sensitive. Make sure that you enter the correct password
and username using the proper casing.
4
It is highly recommended to change the default username and password. Make sure
you store the username and password in a save place.
5.4 Problems with LAN Interface
I cannot access the router from the LAN or ping any computer on the LAN.
STEPS
CORRECTIVE ACTION
1
Check the Ethernet LEDs on the front panel. A LAN LED should be on for a port that has
a PC connected. If it is off, check the cables between your router and the PC. Make sure
you have uninstalled any software firewall for troubleshooting.
2
Make sure that the IP address and the subnet mask is consistent between the router
and the workstation.
5.5 Problems with WAN Interface
Initialization of the ADSL connection failed.
STEPS
CORRECTIVE ACTION
1
Check the cable connections between the ADSL port and the wall jack. The ADSL LED
on the front panel of the router should be on.
2
Check that your VPI, VCI, type of encapsulation and type of multiplexing settings are the
same as what you collected from your telephone company and ISP.
3
Restart the router. If you still have problems, you may need to verify your VPI, VCI, type
of encapsulation and type of multiplexing settings with the telephone company and ISP.
I cannot get a WAN IP address from the ISP.
77
STEPS
CORRECTIVE ACTION
1
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between
them and the wall socket (unless your are using a Central Splitter or Central Filter
Page 79 / 80
installed by the qualified and licensed electrician), and ensure that all line filters are
correctly installed and right way around.
2
Missing line filters or line filters installed the wrong way around can cause problems with
your ADSL connection, including causing frequent disconnects.
Frequent loss of ADSL line sync (disconnections).
STEPS
CORRECTIVE ACTION
1
The ISP provides the WAN IP address after authenticating you. Authentication may be
through the user name and password, the MAC address or the host name.
2
The username and password apply to PPPoE and PPoA encapsulation only. Make sure
that you have entered the correct
Service Type
,
User Name
and
Password
(be sure to
use the correct casing).
5.6 Problems with the Internet Access
I cannot access the Internet.
STEPS
CORRECTIVE ACTION
1
Make sure the router is turned on and connected to the network.
2
If the ADSL LED is off, refer to
Section
5.1.3 (Page 67)
.
3
Verify your WAN settings.
4
Make sure you entered the correct user name and password.
5
For wireless stations, check that both the router and wireless station(s) are using the
same ESSID, channel and WEP keys (if WEP encryption is activated).
Internet connection disconnects.
STEPS
CORRECTIVE ACTION
1
Check the schedule rules.
2
If you use PPPoA or PPPoE encapsulation, check the idle time-out setting.
3
Contact your ISP.
78
Page 80 / 80
If you have any troubles to configure or setup the ENDSL-A2+4R, please feel free to
contact us.
Before contacting us, make sure collect following information. Submit complete detailed
information of your problem will help us to provide you accurate answers.
Model Name:
Serial Number:
PC Settings:
Other:
79

Rate

4 / 5 based on 1 vote.

Popular MyTech Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top