1. Home
    2. /
  2. Manuals
    3. /
  3. Modecom
    4. /
  4. MC-WR22
    5. /
  5. 2
Page 6 / 68 Scroll up to view Page 1 - 5
www.modecom.eu
6
Wireless router
LAN(1,2,3,4): 10/100Mbps RJ45 Auto-sensing. These four LAN ports are
where you will connect other network devices, such as PCs/Laptops, print
servers, remote hard drives, and anything else you want to put on your net-
work. If you connect this product with the Network adapter, Hub (or Switch)
correctly, the Router’s corresponding LED and the Adapter’s, Hub’s (or the
Switch) will illuminate.
WAN: 10/100Mbps RJ45 port. The WAN port is where you will connect
Cable/DSL Modem or other LAN.
RESET(WPS): The Reset Button has three functions, WPS, reboot and
Factory Default. When press it less than 2 second, it is WPS function and
the SYS LED will flash two minute (as long as WPS session is active); 2 to
5 seconds, the router will reboot; and more than 5 seconds, the router will
restore to factory default settings.
Power inlet: 9V DC, 1A Power supply.
2.3 Typical install
1. Make sure all devices, including your PCs, modem, and Router, are
turned on.
2. Using an Ethernet network cable, connect the LAN device or Ethernet
network port of the cable or DSL modem to the Router’s WAN port.
Page 7 / 68
7
Wireless router
Chapter 3 - Quick Install Guide
3.1 TCP/IP Settings
Before you can access and configure router, you have to setup your net
-
work adapter IP address. According to the following steps to obtain IP ad-
dress automatically from router DHCP Server, The following instruction set
up the computer running windows operation system.
Note: The router default IP address is 192.168.1.1
1. Click Start button and choose Settings, then click Control Panel.
2. Double click Network icon and select Configuration tab in the Network
window.
3. Choose the connection you want to use and click it with right mouse but-
ton and choose “Properties”.
4. Double click TCP/IP Protocol.
5. Make sure that option “Obtain IP address automatically” is chosen.
8. Click OK to complete the install procedure.
After all is successful, you can check the TCP/IP information via the follow-
ing command. Start -> run. Type cmd and in the window like the one below
enter command: ipconfig /all.
Page 8 / 68
www.modecom.eu
8
Wireless router
3.2 Getting Started
To access configuration panel open your web browser (MS Internet Explorer,
Firefox, Opera or Chrome) and type the router’s IP address: 192.168.1.1
Default User / Password: admin
If successful, you can see the status page.
Page 9 / 68
9
Wireless router
3.3 Setup Wizard
Click on “Wizard”, it will guide you to setup your router in six simple steps.
Please follow the steps and complete the router configuration.
Step 1 - Setup Operation Mode
The router supports three operation modes, Gateway, Bridge and Wireless ISP.
And each mode is suitable for different use, please choose correct mode.
Page 10 / 68
www.modecom.eu
10
Wireless router
Step 2 - Time Zone Settings
The Time Configuration option allows you to configure, update, and main
-
tain the correct time on the internal system clock.
Time Zone Select: Select the Time Zone from the drop-down menu.
NTP Server: Select the NTP Server from the drop-down menu.
Step 3 - LAN Settings
Setup the IP address and Subnet mask for the LAN interface.
Step 4 - WAN Settings
The Router support five access modes in the WAN side, please choose
correct mode according to your ISP Service.

Rate

4.8 / 5 based on 4 votes.

Popular Modecom Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top