Page 26 / 160
Scroll up to view Page 21 - 25
Chapter 3
The Client Wizard
26
Click
Wifi
in the menu to show the following screen. Configure the wireless settings in this screen.
1
By default, the wireless feature is enabled. If you want to disable it, switch the
Estado
button to
DESACTIVADA
. You can change the Router’s SSID in
Identificador Red Inalámbrica (SSID)
and
select
Visible
if you allow it to be seen by a SSID scan. If not, select
Oculta
.
2
The basic wireless security mode is
WPA2-PSK
. If you want to change the security mode, password,
or encryption mode, you can do so in the
Seguridad
section.
Page 27 / 160
Chapter 3
The Client Wizard
27
3
In the
WPS Configuration
section, you can enable WPS on the Router to quickly set up a secured
wireless network with its clients.
4
You can also configure wireless MAC filter in the
Filtrado MAC
section to allow or deny clients based
on their MAC addresses. Click
Añadir regla
if you want to add more rules.
5
Click
Aplicar
to save your settings and exit the screen.
3.2.2
IPv4 NAT Port Forwarding Configuration
You can configure IPv4 virtual service rules to forward incoming service requests to the server(s) on
your local network.
1
Mouse-over the
Configuración Básica
and
Puertos
to show the
Puertos
menu. Click
Puertos
IPv4.0
.
2
Click
Añadir IPv4.0 regla
to add a new NAT port forwarding rule.
Page 28 / 160
Chapter 3
The Client Wizard
28
3
If you want to add a single port, select
el puerto
in the
Abrir
field and enter the port number and
the internal port number. If you want to add a range of port numbers, select
los puertos
in the
Abrir
field and enter the external start/end ports, the internal start/end ports.
4
Select the protocol used for this rule in the
protocolo
field.
5
Enter the inside IP address of the LAN device to which the virtual server forwards traffic in the
IP del
dispositivo
field.
6
Click
Añadir IPv4.0 regla
to add another virtual service rule. If you want to remove a rule, click the
-
icon next to the rule.
7
Click
Guardar cambios
to save your settings and exit the screen.
3.2.3
IPv6 Firewall Configuration
You can configure IPv6 firewall rules for the Router.
Page 29 / 160
Chapter 3
The Client Wizard
29
1
In the
Puertos
menu. Click
Puertos IPv6.0
.
2
Click
Añadir IPv6.0 regla
to add a new firewall rule.
3
Select if this rule is for one single port or a range of ports in the
Abrir el puerto o Rango de
Puertos de origen
field. Enter the port number or port range.
4
In the
Abrir el puerto o Rango de Puertos de destino
field, enter the internal port number if this
rule is for one single port. Enter the internal port range if this rule is for a range of ports.
Page 30 / 160
Chapter 3
The Client Wizard
30
5
Select the protocol used for this rule in the
protocolo
field.
6
Specify the direction of travel of packets in
Interfaz de Dirección
.
7
Select the interface to which this rule is applied in
Interfaz
.
ALL
means this rule applies to all
interfaces of the Router.
8
Enter the source and destination IPv6 address in the
Dirección IPv6.0 global de origen/destino
fields.
9
In R
egla de acción
, set the default action that the firewall takes on packets that do not match the
rules.
10
Click
Añadir IPv6.0 regla
to add another firewall rule. If you want to remove a rule, click the
-
icon
next to the rule.
11
Click
Terminar
to save your settings and exit the screen.
3.2.4
Connection Line Configuration
Use this screen to configure the connection of the Router with the ONT.
1
Mouse-over the
Configuración Básica
and
Puertos
. Then click
Tu Línea
.
19216811.live