1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WRTP54G
    5. /
  5. 4
Page 16 / 116 Scroll up to view Page 11 - 15
Wireless-G Broadband Router with 2 Phone Ports
8
Chapter 3: Getting to Know the Router
The Front Panel
The Front Panel
The Router’s LEDs, which inform you about network activities, are located on the front panel.
POWER
Blue/Red. The
POWER
LED lights up blue when the Router is powered on. If the blue LED is
flashing, the Router is booting up or upgrading its firmware. If the LED lights up red, then
disconnect the power, and wait five seconds. Then reconnect the power.
ETHERNET 1-4
Blue. The
ETHERNET
LED lights up when there is an active connection through the
corresponding port. If the LED is flashing, then there is traffic moving through that port.
WIRELESS
Blue. The
WIRELESS
LED lights up when there is an active wireless connection. If the LED is
flashing, the Router is sending or receiving data over the wireless network.
PHONE 1-2
Blue. The
PHONE
LED is solidly lit when a telephone or fax machine has an active or
registered connection to babyTEL through the corresponding port (PHONE 1 or 2).
It flashes when the phone is being used or is off the hook.
INTERNET
Blue. The
INTERNET
LED lights up when the Router is connected to your cable or DSL
modem. If the LED is flashing, the Router is sending or receiving data over the Internet port.
Proceed to “Chapter 4: Connecting the Router.”
Figure 3-2: Front Panel
Page 17 / 116
Wireless-G Broadband Router with 2 Phone Ports
9
Chapter 4: Connecting the Router
Overview
Chapter 4: Connecting the Router
Overview
To begin installation of the Router, you will connect the Router to your PCs, telephone(s) or fax machine(s), and
cable or DSL modem. The following connection diagram illustrates a basic network setup with wired
connections to one desktop PC and telephone and a wireless connection to one notebook PC.
Figure 4-1: Router Connection Diagram
Telephone
Router
Cable/DSL
Modem
Internet
Desktop PC
Notebook PC
NOTE:
If you already have a
router in your network, then
replace your existing router with
the Wireless-G Broadband Router
with 2 Phone Ports.
Page 18 / 116
Wireless-G Broadband Router with 2 Phone Ports
10
Chapter 4: Connecting the Router
Connection Instructions
Connection Instructions
1.
Make sure that all of your hardware is powered off, including the Router, PCs, and broadband modem.
2.
Attach the antenna to the Router’s antenna port.
3.
Connect your broadband modem’s Ethernet cable to the Router’s Internet port.
4.
Connect one end of an Ethernet network cable to one of the numbered ports on the back of the Router.
Connect the other end to an Ethernet port on a network device, e.g., a PC, print server, or switch.
Repeat this step to connect more PCs or other network devices to the Router.
5.
Power on the broadband modem.
6.
Connect the included power adapter to the Router’s Power port, and then plug the power adapter into an
electrical outlet. The Power LED on the front panel will light up when the adapter is connected properly.
7.
Power on your PC(s).
8.
Plug a standard telephone into the Router’s Phone1 port.
9.
If you have a second
babyTEL
phone or fax line, repeat step 8 to connect a telephone or fax machine to the
Router’s Phone2 port.
Proceed to the following section, “Placement Options.”
Figure 4-3: Connect a PC
Figure 4-4: Connect the Power
Figure 4-2: Connect the Modem
Figure 4-5: Connect a Telephone
IMPORTANT:
Do not connect the Phone port to a telephone wall jack. Make sure you only connect
a telephone or fax machine to the Phone port. Otherwise, the Router or the telephone wiring in your
home or office may be damaged.
NOTE:
Make sure your
telephone is set to its tone
setting (not pulse).
Page 19 / 116
Wireless-G Broadband Router with 2 Phone Ports
11
Chapter 4: Connecting the Router
Placement Options
Placement Options
There are two ways to place the Router. The first way is to place it horizontally on a surface, so it sits on its four
rubber feet. The second way is to mount it on a wall. This option uses the Router’s four wall-mount slots on its
bottom panel. The distance between two adjacent slots is 62 mm (2.44 inches).
To use the wall-mount option, follow these instructions:
1.
Make sure you have four screws that are size #4—this indicates a diameter measurement of 2.845 mm
(0.112 inches).
2.
Determine where you want to mount the Router.
3.
Drill four holes into the wall. Make sure adjacent holes are 62 mm (2.44 inches) apart.
4.
Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.
5.
Maneuver the Router so the wall-mount slots line up with the four screws.
6.
Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the
wall-mount slots.
Proceed to “Chapter 5: Configuring the Router.”
62 mm
(2.44 inches)
Figure 4-6: Measurement between
Wall-Mount Slots
Page 20 / 116
Wireless-G Broadband Router with 2 Phone Ports
12
Chapter 4: Connecting the Router
Placement Options

Rate

124.8 / 5 based on 304 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top