1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WRT330N
    5. /
  5. 3
Page 11 / 92 Scroll up to view Page 6 - 10
5
Chapter 2: Planning Your Wireless Network
Network Layout
Wireless-N Gigabit Gaming Router
desktop computers, and USB adapters for your USB connectivity needs. The Router can also communicate with
other devices, such as wireless print servers and bridges.
When you wish to connect your wireless network to your wired network, you can use the Router’s four local
Ethernet ports. To add more ports, connect one of the Router's local ports to any Linksys switch.
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com for more information about products that work with the Wireless-N Gigabit Gaming Router.
Page 12 / 92
6
Chapter 3: Getting to Know the Wireless-N Gigabit Gaming Router
The Back Panel
Wireless-N Gigabit Gaming Router
Chapter 3: Getting to Know the Wireless-N Gigabit
Gaming Router
The Back Panel
The Router's ports, where the cables are connected, and Reset button are located on the back panel.
INTERNET
The Internet port is where you will connect your broadband modem.
ETHERNET 1, 2, 3, 4
These ports (1, 2, 3, 4) connect the Router to your wired PCs and other Ethernet network
devices.
Reset Button
There are two ways to reset the Router's factory defaults. Either press the
Reset
button,
for approximately five seconds, or restore the defaults from the Administration - Factory
Defaults tab of the Router's Web-based Utility.
Power
The
Power
port is where you will connect the power adapter.
IMPORTANT:
Resetting the Router will erase all of
your settings (Internet connection, wireless
security, and other settings) and replace them
with the factory defaults. Do not reset the Router
if you want to retain these settings.
Figure 3-1: The Router’s Back Panel
Page 13 / 92
7
Chapter 3: Getting to Know the Wireless-N Gigabit Gaming Router
The Front Panel
Wireless-N Gigabit Gaming Router
The Front Panel
The Router’s LEDs are located on the front panel.
POWER
Green. The
POWER
LED lights up and will stay on while the Router is powered on.
ETHERNET 1, 2, 3, 4
Green/Orange. The numbered LEDs, correspond with the numbered ports on the Router’s
back panel and light up when the Router is connected to a device through the
corresponding port. If the LED is flashing, the Router is sending or receiving data over that
port. The light will be orange when there is a 1000 Mbps gigabit connection.
INTERNET
Green. The
INTERNET
LED lights up when there is a connection through the Internet port.
WIRELESS
Green. The
WIRELESS
LED lights up when there is a wireless connection. If the LED is
flashing, the Router is sending or receiving data over the wireless network.
SECURITY
Green. The
SECURITY
LED is green when PSK/PSK2 is enabled.
Orange. The
SECURITY
LED is orange when WEP is enabled or no security is enabled.
Off. The
SECURITY
LED is off when the security button on the top of the unit is disabled.
The Top Panel
The Router has a button reserved for a future function.
Figure 3-2: The Router’s Front Panel
Figure 3-3: The Router’s Top Panel
Button
Page 14 / 92
8
Chapter 4: Connecting the Wireless-N Gigabit Gaming Router
Hardware Installation
Wireless-N Gigabit Gaming Router
Chapter 4: Connecting the Wireless-N Gigabit Gaming
Router
Hardware Installation
1.
Make sure that all of your hardware is powered off, including the broadband modem and PCs.
2.
Connect your broadband modem’s Ethernet cable to the Router’s Internet port.
3.
Connect one end of an Ethernet network cable to one of the numbered ports on the back of the Router.
Connect the other end to an Ethernet port on a network device, e.g., a PC, print server, or switch.
Repeat this step to connect more PCs or other network devices to the Router.
4.
Power on the broadband modem.
5.
Connect the included power adapter to the Router’s Power port, and then plug the power adapter into an
electrical outlet. The Power LED on the front panel will light up when the adapter is connected properly.
6.
Power on your PC(s).
7.
Locate an optimum location for the Router. The best place for the Router is usually at the center of your
wireless network, with line of sight to all of your wireless devices.
Proceed to “Chapter 5: Configuring the Wireless-N Gigabit Gaming Router”.
Figure 4-1: Connect the Modem
Figure 4-2: Connect a PC
Figure 4-3: Connect the Power
IMPORTANT:
Make sure you use the power
adapter that is supplied with the Router. Use of a
different power adapter could damage the Router.
Page 15 / 92
9
Chapter 5: Configuring the Wireless-N Gigabit Gaming Router
Overview
Wireless-N Gigabit Gaming Router
Chapter 5: Configuring the Wireless-N Gigabit Gaming
Router
Overview
Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run
the Setup Wizard on the Setup CD-ROM, then you can use the Web-based Utility to configure the Router. For
advanced users, you may configure the Router’s advanced settings through the Web-based Utility.
This chapter describes each web page on the Utility and each page’s key functions. The Utility can be accessed
via your web browser through use of a computer connected to the Router. For a basic network setup, most users
only have to use the following screens of the Utility:
•
BASIC SETUP. On the
BASIC SETUP
screen, enter the Internet connection settings provided by your Internet
Service Provider (ISP). If you do not have this information, you can call your ISP to request the settings. When
you have the setup information, then you can configure the Router.
•
MANAGEMENT. Click the
ADMINISTRATION
tab and then the
MANAGEMENT
tab. The Router’s default
password is
admin
. To secure the Router, change the password from its default.
•
WIRELESS. On the
BASIC WIRELESS SETTINGS
screen, set the basic configuration for your wireless network.
There are seven main tabs: SETUP, WIRELESS, SECURITY, ACCESS RESTRICTIONS, APPLICATIONS & GAMING,
ADMINISTRATION, and STATUS. Additional tabs will be available after you click one of the main tabs.
SETUP
•
BASIC SETUP. Enter the Internet connection and network settings on this screen.
•
DDNS. Enable the Router’s Dynamic Domain Name System (DDNS) feature on this screen.
•
MAC ADDRESS CLONE. If you need to clone a MAC address onto the Router, use this screen.
•
ADVANCED ROUTING. Use this screen to alter dynamic and static routing configurations.

Rate

4.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top