1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WRT110
    5. /
  5. 3
Page 11 / 39 Scroll up to view Page 6 - 10
Chapter±3
Advanced Configuration
10
RangePlus W±reless Router
MTU
MTU is the Maximum Transmission Unit. It specifies
the largest packet size permitted for Internet transmission.
Select Manual if you want to manually enter the largest
packet size that is transmitted. To have the Router select
the best MTU for your Internet connection, keep the
default setting,
Auto
.
S±ze
When Manual is selected in the
MTU
field, this option
is enabled. Leave this value in the 1200 to 1500 range. The
default size depends on the Internet Connection Type:
DHCP, Static IP, or Telstra:
1³00
PPPoE:
1²92
PPTP or L2TP:
1²´0
Network Setup
The Network Setup section changes the settings on the
network connected to the Router’s Ethernet ports. Wireless
setup is performed through the Wireless tab.
Router IP
This presents both the Router’s IP Address and Subnet
Mask as seen by your network.
Router IP
DHCP Server Setting
The settings allow you to configure the Router’s Dynamic
Host Configuration Protocol (DHCP) server function. The
Router can be used as a DHCP server for your network. A
DHCP server automatically assigns an IP address to each
computer on your network. If you choose to enable the
Router’s DHCP server option, make sure there is no other
DHCP server on your network.
DHCP Server Setting
DHCP Server
DHCP is enabled by factory default. If you
already have a DHCP server on your network, or you don’t
want a DHCP server, then select
D±sabled
(no other DHCP
features will be available).
DHCP Reservat±on
Click this button if you want to assign
a fixed local IP address to a MAC address.
•
•
•
DHCP Reservation
You will see a list of DHCP clients with the following
information: Client Name, Interface, IP Address, and
MAC Address.
DHCP Reservation
Select Cl±ents from DHCP Table
Click the
Select
check box to reserve a client’s IP address. Then click
Add Cl±ents
.
Manually Add±ng Cl±ent
To manually assign an IP
address, enter the client’s name in the
Enter Client
Name
field. Enter the IP address you want it to have in
the
Assign IP Address
field. Enter its MAC address in the
To This MAC Address
field. Then click
Add
.
Clients Already Reserved
A list of DHCP clients and their fixed local IP addresses
will be displayed at the bottom of the screen. If you
want to remove a client from this list, click
Remove
.
Click
Save Sett±ngs
to apply your changes, or click
Cancel Changes
to cancel your changes. To view the
most up-to-date information, click
Refresh
. To exit this
screen, click
Close
.
Start IP Address
Enter a value for the DHCP server to
start with when is
suing IP addresses. Because the Router’s
default IP address is 192.168.1.1, the Start IP Address must
be 192.168.1.2 or greater, but smaller than 192.168.1.253.
The default Starting IP Address is
192.1´8.1.100
.
Max±mum
Number
of
Users
Enter
the
maximum
number of PCs that you want the DHCP server to assign
IP addresses to. This number cannot be greater than 253.
The default is
³0
.
IP Address Range
Displayed here is the range of available
IP addresses.
•
•
Page 12 / 39
Chapter±3
Advanced Configuration
11
RangePlus W±reless Router
Cl±ent Lease T±me
The Client Lease Time is the amount
of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the
amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the time is up, the user will
be automatically assigned a new dynamic IP address. The
default is
0
minutes, which means one day.
Stat±c DNS 1-3
The Domain Name System (DNS) is how
the Internet translates domain or website names into
Internet addresses or URLs. Your ISP will provide you with at
least one DNS Server IP Address. If you wish to use another,
enter that IP Address in one of these fields. You can enter up
to three DNS Server IP Addresses here. The Router will use
these for quicker access to functioning DNS servers
.
WINS
The Windows Internet Naming Service (WINS)
manages each PC’s interaction with the Internet. If you
use a WINS server, enter that server’s IP Address here.
Otherwise, leave this blank.
Time Setting
T±me Zone
Select the time zone in which your network
functions from this drop-down menu. (You can even
automatically adjust for daylight saving time.)
Time Setting
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
Setup > DDNS
The Router offers a Dynamic Domain Name System (DDNS)
feature. DDNS lets you assign a fixed host and domain
name to a dynamic Internet IP address. It is useful when
you are hosting your own website, FTP server, or other
server behind the Router.
Before you can use this feature, you need to sign
up for DDNS service with a DDNS service provider,
www.dyndns.org or www.TZO.com. If you do not want to
use this feature, keep the default setting,
D±sabled
.
DDNS
DDNS Service
If your DDNS service is provided by DynDNS.org, then
select
DynDNS.org
from the drop-down menu. If your
DDNS service is provided by TZO, then select
TZO.com
.
The features available on the
DDNS
screen will vary,
depending on which DDNS service provider you use.
DynDNS.org
Setup > DDNS > DynDNS
Username
Enter the Username for your DDNS account.
Password
Enter the Password for your DDNS account.
Host Name
The is the DDNS URL assigned by the DDNS
service.
W±ldcard
This setting enables or disables wildcards
for your host. For example, if your DDNS address is
myplace.dyndns.org
and you enable wildcards, then
x.myplace.dyndns.org
will work as well (x is the wildcard).
To disable wildcards, keep the default,
D±sabled
. To enable
wildcards, select
Enabled
. If you are not sure which setting
to select, keep the default,
D±sabled
.
Internet IP Address
The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Status
The status of the DDNS service connection is
displayed here.
Update
To manually trigger an update, click this button.
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
TZO.com
Setup > DDNS > TZO
Page 13 / 39
Chapter±3
Advanced Configuration
12
RangePlus W±reless Router
E-ma±l Address, TZO Key, and Doma±n Name
Enter the
settings of the account you set up with TZO.
Internet IP Address
The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Status
The status of the DDNS service connection is
displayed here.
Update
To manually trigger an update, click this button.
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
Setup > MAC Address Clone
A MAC address is a 12-digit code assigned to a unique
piece of hardware for identification. Some ISPs will require
you to register a MAC address in order to access the
Internet. If you do not wish to re-register the MAC address
with your ISP, you may assign the MAC address you have
currently registered with your ISP to the Router with the
MAC Address Clone feature.
Setup > MAC Address Clone
MAC Address Clone
Enabled/D±sabled
To have the MAC Address cloned,
select
Enabled
.
MAC Address
Enter the MAC Address registered with
your ISP here.
Clone My PC’s MAC
Click this button to clone the MAC
address of the computer you are using.
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
Setup > Advanced Routing
This screen is used to set up the Router’s advanced
functions. Dynamic Routing automatically adjusts how
packets travel on your network. Static Routing sets up a
fixed route to another network destination.
Setup > Advanced Routing
Advanced Routing
NAT
Enabled/D±sabled
If this Router is hosting your network’s
connection to the Internet, keep the default,
Enabled
. If
another router exists on your network, select
D±sabled
.
When the NAT setting is disabled, dynamic routing will be
enabled.
Dynamic Routing (RIP)
Enabled/D±sabled
This feature enables the Router to
automatically adjust to physical changes in the network’s
layout and exchange routing tables with the other router(s).
The Router determines the network packets’ route based
on the fewest number of hops between the source and
the destination. When the NAT setting is enabled, the
Dynamic Routing feature is automatically disabled. When
the NAT setting is disabled, this feature is available. Select
Enabled
to use the Dynamic Routing feature.
Static Routing
A static route is a pre-determined pathway that network
information must travel to reach a specific host or network.
Enter the information described below to set up a new
static route.
Route Entr±es
To set up a static route between the Router
and another network, select a number from the drop-
down list. Click
Delete Th±s Entry
to delete a static route.
Enter Route Name
Enter a name for the Route here,
using a maximum of 25 alphanumeric characters.
Dest±nat±on LAN IP
The Destination LAN IP is the address
of the remote network or host to which you want to assign
a static route.
Subnet
Mask
The
Subnet
Mask
determines
which
portion of a Destination LAN IP address is the network
portion, and which portion is the host portion.
Page 14 / 39
Chapter±3
Advanced Configuration
13
RangePlus W±reless Router
Gateway
This is the IP address of the gateway device that
allows for contact between the Router and the remote
network or host.
Interface
This interface tells you whether the Destination
IP Address is on the
LAN & W±reless
(Ethernet and wireless
networks) or the
WAN
(Internet)
.
Click
Show Rout±ng Table
to view the static routes you
have already set up.
Advanced Routing > Routing Table
Routing Table
For each route, the Destination LAN IP address, Subnet
Mask, Gateway, and Interface are displayed. Click
Refresh
to update the information. Click
Close
to exit
this screen.
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
Wireless > Basic Wireless Settings
The basic settings for wireless networking are set on this
screen.
Wireless > Basic Wireless Settings
Wireless Network
Network Mode
From this drop-down menu, you can
select the wireless standards running on your network. If
you have Wireless-N, Wireless-G, and Wireless-B devices in
your network, keep the default setting,
M±xed
. If you have
only Wireless-G and Wireless-B devices in your network,
select
BG-M±xed
. If you have only Wireless-N devices,
select
W±reless-N Only
. If you have only Wireless-G
devices, select
W±reless-G Only
. If you have only Wireless-
B devices, select
W±reless-B Only
. If you do not have any
wireless devices in your network, select
D±sabled
.
Network Name (SSID)
The SSID is the network name
shared among all points in a wireless network. The
SSID must be identical for all devices in the wireless
network. It is case-sensitive and must not exceed
32 characters (use any of the characters on the keyboard).
Make sure this setting is the same for all points in your
wireless network. For added security, you should change
the default SSID (
l±nksys
) to a unique name.
Rad±o Band
For best performance in a network using
Wireless-N, Wireless-G and Wireless-B devices, keep the
default,
Auto - 20/²0MHz Channel
. For Wireless-G and
Wireless-B networking only, select
Standard - 20MHz
Channel
.
NOTE:
If you select Auto - 20/40MHz Channel
for the Radio Band setting, then Wireless-N can
use two channels: a primary one (Wide Channel)
and a secondary one (Standard Channel). This
will enhance Wireless-N performance.
W±de Channel
If you selected Auto
- 20/40MHz Channel
for the Radio Band setting, then this setting will be
available for your primary Wireless-N channel. Select any
channel from the drop-down menu. If you are not sure
which channel to select, keep the default,
Auto
.
Standard Channel
Select the channel for Wireless-N,
Wireless-G, and Wireless-B networking. If you selected
Auto – 20/40MHz Channel for the Radio Band setting,
then the Standard Channel will be a secondary channel
for Wireless-N. If you are not sure which channel to select,
keep the default,
Auto
.
SSID Broadcast
When wireless clients survey the local
area for wireless networks to associate with, they will
detect the SSID broadcast by the Router. To broadcast the
Router’s SSID, keep the default setting,
Enabled
. If you
do not want to broadcast the Router’s SSID, then select
D±sabled
.
Click
Save Sett±ngs
to apply your changes, or click
Cancel
Changes
to cancel your changes.
Wireless > Wireless Security
The
Wireless Security
screen configures the security of
your wireless network. There are six wireless security
mode options supported by the Router: WPA Personal,
WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,
and WEP. (WPA stands for Wi-Fi Protected Access, which
is a security standard stronger than WEP encryption. WEP
stands for Wired Equivalent Privacy, while RADIUS stands
for Remote Authentication Dial-In User Service.) These
six are briefly discussed here. For detailed instructions
Page 15 / 39
Chapter±3
Advanced Configuration
1²
RangePlus W±reless Router
on configuring wireless security for the Router, refer to
“Chapter 2: Wireless Security Checklist.”
Wireless Security
Security Mode
Select the security method for your wireless network. If
you do not want to use wireless security, keep the default,
D±sabled
.
WPA Personal
NOTE:
If you are using WPA, always remember
that each device in your wireless network MUST
use the same WPA method and shared key, or
else the network will not function properly.
Security Mode > WPA Personal
Encrypt±on
WPA supports two encryption methods, TKIP
and AES, with dynamic encryption keys. Select the type of
algorithm,
TKIP
or
AES
. The default is
TKIP
.
Passphrase
Enter a Passphrase of 8-63 characters.
Key Renewal
Enter a Key Renewal period, which instructs
the Router how often it should change the encryption keys.
The default Group Key Renewal period is
3´00
seconds.
WPA2 Personal
Security Mode > WPA2 Personal
Encrypt±on
WPA2 supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm,
AES
or
AES or TKIP
. The default is
AES
or TKIP
.
Passphrase
Enter a Passphrase of 8-63 characters.
Key Renewal
Enter a Key Renewal period, which instructs
the Router how often it should change the encryption keys.
The default Group Key Renewal period is
3´00
seconds.
WPA Enterprise
This option features WPA used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
Security Mode > WPA Enterprise
Encrypt±on
WPA supports two encryption methods, TKIP
and AES, with dynamic encryption keys. Select the type of
algorithm,
TKIP
or
AES
. The default is
TKIP
.
RADIUS Server
Enter the IP address of the RADIUS
server.
RADIUS Port
Enter the port number of the RADIUS
server. The default value is
1812
.
Shared Secret
Enter the key shared between the Router
and the server.
Key Renewal
Enter a Key Renewal period, which instructs
the Router how often it should change the encryption
keys. The default Key Renewal period is
3´00
seconds.
WPA2 Enterprise
This option features WPA2 used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top