1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WRT100
    5. /
  5. 6
Page 26 / 37 Scroll up to view Page 21 - 25
Chapter±3
Advanced Configuration
22
RangePlus W±reless Router
Diagnostics
Ping Test
The Ping test checks the status of a connection.
IP or URL Address
Enter the address of the PC whose
connection you wish to test.
Packet S±ze
Enter the packet size you want to use. The
default is
32
bytes.
T±mes to P±ng
Enter many times you wish to test it.
Start to P±ng
To run the test, click this button. The
Ping 
Test
screen will show if the test was successful. Click
Close
to return to the
Diagnostics
screen.
Diagnostics > Ping
Traceroute Test
The
Traceroute
test
tests
the
performance
of
a
connection.
IP or URL Address
Enter the address of the PC whose
connection you wish to test.
Start to Traceroute
To run the test, click this button. The
Traceroute Test
screen will show if the test was successful.
Click
Close
to return to the
Diagnostics
screen.
Diagnostics > Traceroute
Administration > Factory Defaults
The
Administration  >  Factory  Defaults
screen allows you
to restore the Router’s configuration to its factory default
settings.
Administration > Factory Defaults
NOTE:
Do not restore the factory defaults unless
you are having difficulties with the Router and
have
exhausted
all
other
troubleshooting
measures. Once the Router is reset, you will have
to re-enter all of your configuration settings.
Factory Defaults
Restore Factory Defaults
To reset the Router’s settings
to the default values, click this button and then follow the
on-screen instructions. Any settings you have saved will
be lost when the default settings are restored.
Administration > Firmware Upgrade
The
Firmware  Upgrade
screen allows you to upgrade the
Router’s firmware. Do not upgrade the firmware unless
you are experiencing problems with the Router or the new
firmware has a feature you want to use.
Administration > Firmware Upgrade
Page 27 / 37
Chapter±3
Advanced Configuration
23
RangePlus W±reless Router
NOTE:
The Router may lose the settings you
have
customized.
Before
you
upgrade
its
firmware, write down all of your custom settings.
After you upgrade its firmware, you will have to
re-enter all of your configuration settings.
Upgrade Firmware
Before upgrading the firmware, download the Router’s
firmware
upgrade
file
from
the
Linksys
website,
www.linksys.com. Then extract the file.
Please select a F±le to Upgrade
Click
Browse
and select
the extracted firmware upgrade file.
Start
to
Upgrade
After
you
have
selected
the
appropriate file, click this button, and f
ollow the on-screen
instructions.
Status > Router
The
Router
screen displays information about the Router
and its current settings.
Status > Router
Router Information
F±rmware Vers±on
This is the version number of the
Router’s current firmware.
Current T±me
This shows the time set on the Router.
Internet MAC Address
This is the Router’s MAC Address,
as seen by your ISP.
Host Name
If required by your ISP, this was entered on
the
Basic Setup
screen.
Doma±n Name
If required by your ISP, this was entered
on the
Basic Setup
screen.
Internet Connection
This section shows the current network information
stored in the Router. The information varies depending on
the Internet connection type selected on the
Basic Setup
screen.
Click
Refresh
to update the on-screen information.
Status > Local Network
The
Local Network
screen displays information about the
local, wired network.
Status > Local Network
Local Network
Local MAC Address
The MAC address of the Router’s
local, wired interface is displayed here.
Router IP Address
This shows the Router’s IP address, as
it appears on your local network.
Subnet Mask
This shows the Subnet Mask of the Router.
DHCP Server
DHCP Server
The status of the Router’s DHCP server
function is displayed here.
Start IP Address
For the range of IP addresses used by
devices on your local network, the starting IP address is
shown here.
End IP Address
For the range of IP addresses used by
devices on your local network, the ending IP address is
shown here.
DHCP Cl±ents Table
Click this button to view a list of PCs
that are using the Router as a DHCP server.
Page 28 / 37
Chapter±3
Advanced Configuration
24
RangePlus W±reless Router
DHCP Clients Table
DHCP Client Table
The DHCP Client Table lists computers and other
devices that have been assigned IP addresses by the
Router. The list can be sorted by Client Name, Interface,
IP Address, MAC Address, and Expired Time (how
much time is left for the current IP address). To remove
a DHCP client, click
Delete
. To retrieve the most up-to-
date information, click
Refresh
. To exit this screen and
return to the
Local Network 
screen, click
Close
.
Status > Wireless Network
The
Wireless  Network
screen displays information about
your wireless network.
Status > Wireless
Wireless Network
MAC Address
The MAC address of the Router’s local,
wireless interface is displayed here.
Mode
Displayed here is the wireless mode used by the
network.
Network Name (SSID)
Displayed here is the name of the
wireless network, which is also called the SSID.
Rad±o Band
Shown here is the Radio Band setting
selected on the
Basic Wireless Settings
screen.
W±de Channel
Shown here is the Wide Channel setting
selected on the
Basic Wireless Settings
screen.
Standard Channel
Shown here is the Standard Channel
setting selected on the
Basic Wireless Settings
screen.
Secur±ty
Displayed here is the wireless security method
used by the Router.
SSID Broadcast
Displayed here is the status of the SSID
Broadcast feature.
Page 29 / 37
Appendix±A
Troubleshooting
25
RangePlus W±reless Router
Append±x A:
Troubleshoot±ng
Your computer cannot connect to the Internet.
Follow these instructions until your computer can connect
to the Internet:
Make sure that the Router is powered on. The Power
LED should be green and not flashing.
If the Power LED is flashing, then power off all of
your network devices, including the modem, Router,
and computers. Then power on each device in the
following order:
Cable or DSL modem
Router
Computer
Check the cable connections. The computer should
be connected to one of the ports numbered 1-4 on
the Router, and the modem must be connected to the
Internet port on the Router.
The modem does not have an Ethernet port.
The modem is a dial-up modem for traditional dial-up
service. To use the Router, you need a cable/DSL modem
and high-speed Internet connection.
You cannot use the DSL service to connect manually to
the Internet.
After you have installed the Router, it will automatically
connect to your Internet Service Provider (ISP), so you no
longer need to connect manually.
The DSL telephone line does not fit into the Router’s
Internet port.
The Router does not replace your modem. You still need
your DSL modem in order to use the Router. Connect
the telephone line to the DSL modem, insert the setup
CD into your computer, and then follow the on-screen
instructions.
•
•
1.
2.
3.
•
When you double-click the web browser, you are
prompted for a username and password. If you want to
get rid of the prompt, follow these instructions.
Launch the web browser and perform the following steps
(these steps are specific to Internet Explorer but are similar
for other browsers):
Select
Tools
>
Internet Opt±ons
.
Click the
Connect±ons
tab.
Select
Never d±al a connect±on
.
Click
OK
.
The Router does not have a coaxial port for the cable
connection.
The Router does not replace your modem. You still need
your cable modem in order to use the Router. Connect your
cable connection to the cable modem, insert the setup
CD into your computer, and then follow the on-screen
instructions.
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same
on both the computer and the Router. If you have enabled
wireless security, then make sure the same security
method and key are used by both the computer and the
Router.
You need to modify the settings on the Router.
Open the web browser (for example, Internet Explorer or
Firefox), and enter the Router’s IP address in the address
field (the default IP address is
²92.²68.².²
). When
prompted, leave the
User name
field blank and enter the
password to the Router (the default is
adm±n
). Click the
appropriate tab to change the settings.
WEB:
If your questions are not addressed here,
refer to the Linksys website,
www.l±nksys.com
.
1.
2.
3.
4.
Page 30 / 37
Appendix±B
Specifications
26
RangePlus W±reless Router
Append±x B:
Spec±f±cat±ons
Model
WRT100
Standards
IEEE 802.11g, IEEE 802.11b,
IEEE 802.3, IEEE 802.3u
Ports
Internet: One 10/100 RJ-45 Port
Ethernet: Four 10/100 RJ-45 Ports
One Power Port
Buttons
One Reset Button
LEDs
Power, Ethernet (1-4), Internet,
Wireless, Security
Cabling Type
CAT 5e
# of Antennas
2
Detachable
No
RF Pwr (EIRP) in dBm 16.5 dBm
Antenna Gain in dBi
1.8 dBi
UPnP able/cert
Able
Security Features
Stateful Packet Inspection (SPI)
Firewall, Internet Policy
Wireless Security
Wi-Fi Protected Access™ 2 (WPA2),
WEP, Wireless MAC Filtering
Security Key Bits
128 Bits, 256 Bits
Env±ronmental
Dimensions
5.83" x 1.42" x 6.69"
(148 x 36 x 170 mm)
Weight
11.78 oz (334 g)
Power
12V, 1A
Certification
FCC, IC-03, Wi-Fi (802.11b/g),
WPA2, WMM
Operating Temp.
0 to 40°C (32 to 104°F)
Storage Temp.
-20 to 60°C (-4 to 140°F)
Operating Humidity
10 to 85% Noncondensing
Storage Humidity
5 to 90% Noncondensing

Rate

4.7 / 5 based on 3 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top