1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WRP400
    5. /
  5. 3
Page 11 / 155 Scroll up to view Page 6 - 10
1
Cisco WRP400 User Guide
9
Getting to Know the WRP400
Thank you for choosing the Cisco WRP400 Wireless-G Broadband Router with 2
Phone Ports. The WRP400 lets you access the Internet via a wireless connection
or through one of its four switched ports. You can also use the WRP400 to share
resources such as computers, printers and files. The built-in phone adapter
enables Voice-over-IP (VoIP) calls even while you are using the Internet.
Front Panel
Page 12 / 155
Getting to Know the WRP400
Front Panel
Cisco WRP400 User Guide
10
1
LED
Description
USB:
For information about supported USB devices, visit the WRP400
product page on Cisco.com:
ps10028/index.html
Wi-Fi Protected Setup (White/Orange): If you have client devices,
such as wireless adapters, that support Wi-Fi Protected Setup, then
you can use Wi-Fi Protected Setup to automatically configure
wireless security for your wireless network(s).
To use Wi-Fi Protected Setup, run the Setup Wizard, or refer to
“Wireless > Basic Wireless Settings,” on page 39
.
The Wi-Fi Protected Setup button lights up white and stays on while
wireless security is enabled on your wireless network(s). The LED
lights up orange if there is an error during the Wi-Fi Protected Setup
process. Make sure the client device supports Wi-Fi Protected
Setup. Wait until the LED is off, and then try again.
Power (Green/Red/Orange):
This LED indicates the status of power
and the progress of the self-diagnostic test upon bootup. If a USB
modem is connected to the USB port, this LED indicates the progress
of initialization and the status of the mobile network connection.
•
Power:
The Power LED shines green and stays on while the WRP400 is
powered on. If the LED shines red, verify that the correct power adapter
is used. If the LED remains red, contact your service provider for
support.
•
Self-diagnostic test:
During boot-up, the LED flashes green to indicate
that the self-diagnostic test is in progress. When the test is complete,
the LED shines steady green.
•
Initialization of a USB modem:
When you connect a device to the USB
port, the Power LED flashes green and orange, indicating that
initialization is in progress. After the device initializes, the Power LED
shines steady green. If the device fails to initialize, the LED continues to
flash green and orange.
Page 13 / 155
Getting to Know the WRP400
Front Panel
Cisco WRP400 User Guide
11
1
•
Mobile network connection:
If a USB modem is installed, the mobile
network connection is used as a failover when an Ethernet connection is
unavailable. The Power LED shows the status of the mobile network:
•
Flashing Orange:
The WRP400 is attempting to connect to the
Internet through the mobile network connection.
•
Steady Orange:
The WRP400 is connected to the Internet through
the mobile network connection.
•
Continuous Flashing Orange:
The WRP400 failed to connect to the
Internet through the mobile network connection and is trying again.
•
Steady Green:
If a USB device is connected, this LED behavior
indicates that the device was successfully initialized and that the
WRP400 is not using the mobile network connection. If the USB
device is removed, this LED behavior indicates that theWRP400 has
power.
Phone 1-2 (Green):
The Phone 1 or 2 LED lights up and stays on
when an active line is registered to the corresponding port on the
back panel. The LED slowly flashes when voicemail messages are
waiting.
Wireless (Green):
The Wireless LED lights up when the wireless
feature is enabled. It flashes when the WRP400 is actively sending or
receiving data over the network.
Ethernet 1-4 (Green):
These numbered LEDs, corresponding with
the numbered ports on the back panel, serve two purposes. If the
LED is solidly lit, the WRP400 is connected to a device through that
port. It flashes to indicate network activity over that port.
Internet (Green):
The Internet LED lights up and stays on when an
Internet connection is made through the Internet port. It flashes to
indicate network activity over the Internet port.
NOTE:
The Power LED indicates Internet connectivity through the
mobile network connection. See the information for the Power LED in
this table.
LED
Description
Page 14 / 155
Getting to Know the WRP400
Back Panel
Cisco WRP400 User Guide
12
1
Back Panel
Port
Description
Internet:
Use this port to connect the WRP400 to a cable or DSL
Internet connection.
Phone 1-2:
Use these ports to connect standard analog telephones
to the WRP400.
Ethernet 1, 2, 3, 4:
Use these Ethernet ports to connect the WRP400
to wired computers and other Ethernet network devices.
Power:
Use the power port to connect the power adapter.
Page 15 / 155
Getting to Know the WRP400
Side Panel
Cisco WRP400 User Guide
13
1
Side Panel
Placement Positions
There are three ways to physically install the WRP400:
•
Horizontal Placement:
The WRP400 has four rubber feet on the bottom
panel. Place the WRP400 on a level surface near an electrical outlet.
•
Vertical Placement:
The WRP400 has a stand on the side panel opposite to
the antenna. Rotate the stand 90 degrees, and place the WRP400 on a level
surface near an electrical outlet.
•
Wall-Mounting Placement:
The WRP400 has four wall-mount slots on its
back panel.
Reset:
There are two ways to reset the WRP400 to the factory
default settings. Either press and hold the Reset button for
approximately ten seconds, or restore the defaults from the
Administration >Factory Defaults screen of the administration web
server. (The Factory Defaults screen allows you to restore the router
and voice defaults separately.)
NOTE:
Restoring the voice defaults may require your login (the
default user name and password are admin). If the defaults do not
work, contact your service provider for more information.
Stand:
To place the WRP400 in a vertical position, rotate the stand 90
degrees.

Rate

4.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top