Page 21 / 74
Scroll up to view Page 16 - 20
15
Chapter 5: Windows Driver Installation
Installation
Wireless-G PrintServer
6.
The
Select Program Folder
screen will appear. An icon will be added to the program folder listed. You may
change the name for the program folder, if you wish. Click
Next
.
You can also click
Back
to return to the previous screen or click
Cancel
to end the driver installation.
7.
When the driver is installed, the
Setup Complete
screen will appear. The Print Driver must still be configured,
so make sure that
Configure Print Driver now
is selected. Click
Finish
to end the driver installation and
begin the driver configuration.
Figure 5-4: Select Program Folder
Figure 5-5: Setup Complete
Downloaded from
www.Manualslib.com
manuals search engine
Page 22 / 74
16
Chapter 5: Windows Driver Installation
Starting the Print Driver Utility
Wireless-G PrintServer
Starting the Print Driver Utility
1.
Click
Start
,
Programs
,
Print Server Utility
, and then
Print Driver Setup
. If the Print Driver Setup icon has
been created, you can double-click it instead.
2.
The
Information
screen will appear. Read the on-screen information, and then click
OK
.
3.
The
Printer Port Setup
screen will appear and list the PrintServer and its ports. Select a printer port to add,
and then click
Next
.
If the PrintServer or printer isn’t listed, make sure that the cable connections are good and the PrintServer
and printer are powered on.
4.
You will be informed that the PrintServer Port has been added successfully. Click
OK
.
Figure 5-7: Printer Port Setup
Figure 5-6: Information
Downloaded from
www.Manualslib.com
manuals search engine
Page 23 / 74
17
Chapter 5: Windows Driver Installation
Starting the Print Driver Utility
Wireless-G PrintServer
5.
The
Configure Printer Port
screen will appear. Your installed printer(s) will appear in the field. Select the
printer you want, and click the
Connect
button to associate the printer with your selected printer port. To add
another printer, click the
Add New Printer
button.
Click
Cancel
to cancel the setup.
6.
Click
Close
to close the
Printer Port Setup
screen. Click
Refresh
to refresh the screen.
The driver installation and configuration is complete. You can now use the PrintServer.
If you would like to change the PrintServer’s settings, use the PrintServer’s web-based utility. For
more information, refer to “Chapter 6: Configuring the PrintServer Using the Web-based Utility.”
Figure 5-8: Configure Printer Port
Downloaded from
www.Manualslib.com
manuals search engine
Page 24 / 74
18
Chapter 6: Configuring the PrintServer Using the Web-based Utility
Overview
Wireless-G PrintServer
Chapter 6: Configuring the PrintServer Using the
Web-based Utility
Overview
After setting up the PrintServer with the Setup Wizard, the PrintServer will be ready for use. However, if you’d like
to change its settings, use the PrintServer’s web-based utility. This chapter will describe each web page of the
utility and each page’s key functions. The utility can be accessed via your web browser through the use of a
networked computer.
There are six main tabs: Setup, Protocol, Wireless, Printer, Status, and Exit. Additional tabs will be available after
you click one of the main tabs, except for the Setup tab.
To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the PrintServer’s IP
address in the
Address
field. Then press
Enter
.
NOTE:
Use the PrintServer’s IP address that you noted when you ran the Setup Wizard. Otherwise,
insert the Setup CD-ROM, and when the
Welcome
screen appears, click
Setup Wizard
. Follow the
instructions until you reach the
Wireless-G PrintServer Setup
screen. Note the IP address, and then
click
Back
until you reach the
Welcome
screen. Click
Exit
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 25 / 74
19
Chapter 6: Configuring the PrintServer Using the Web-based Utility
The Setup Tab
Wireless-G PrintServer
The Setup Tab
The first screen that appears is the Setup tab and allows you to change the PrintServer’s general settings.
WPS54G Device Name
Enter the PrintServer’s name in the field provided. The name is located on a sticker on the bottom of the
PrintServer.
Password
Current Password
. To change the PrintServer’s password, enter the current password in the
Current Password
field.
New Password and Verify Password
. Enter the new password in the
New Password
field, and then enter the
new password again in the
Verify Password
field.
Protocols
The TCP/IP protocol is enabled by default.
Enable: Apple Talk or NetBEUI
. Check the box(es) for AppleTalk or NetBEUI, if they are used by your network.
Click the
Save
button to apply your changes, or click
Cancel
to cancel your changes.
Figure 6-1: Setup Tab
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live