Page 16 / 35 Scroll up to view Page 11 - 15
Appendix B
Specifications
13
Wireless-N Ethernet Bridge with Dual-Band
Appendix B:
Specifications
Model
WET610N
Standards
IEEE 802.3u, 802.11g, 802.11b,
802.11a, draft 802.11n
LEDs
Power, Ethernet, Wi-Fi Protected
Setup™, Wireless
Ports
Ethernet, Power
Buttons
Reset, Wi-Fi Protected Setup™
Cabling Type
CAT5e
# of Antennas
3 (internal)
Antenna Connector
Type
N/A
Detachable (Yes/No) No
Modulations
802.11a: OFDM/BPSK, QPSK,
16-QAM, 64-QAM
802.11b: CCK/QPSK, BPSK
802.11g: OFDM/BPSK, QPSK,
16-QAM, 64-QAM
802.11n: OFDM/BPSK, QPSK,
16-QAM, 64-QAM
RF Pwr (EIRP) in dBm 802.11a: 15 dBm (typical) @
54Mbps
802.11b: 18 dBm (typical) @
11 Mbps
802.11g: 16 dBm (typical) @
54 Mbps
802.11n: 12 dBm (typical) @
130 Mbps (HT20), 270 Mbps (HT40)
Receive Sensitivity
802.11a: -72 dBm (typical) @
54 Mbps
802.11b: -85 dBm (typical) @
11 Mbps
802.11g: -73 dBm (typical) @
54 Mbps
802.11n: -70 dBm (typical) @
MCS15/2.4 GHz,
-69 dBm (typical) @
MCS15/5.0 GHz
Antenna Gain in dBi
1
Wireless Security
WEP, Wi-Fi Protected Access™ 2
(WPA2)
Security Key Bits
Up to 128-Bit Encryption
OS Requirements
Windows XP, Vista, or Vista 64-Bit
Edition with Latest Updates (for
Setup Wizard only)
Environmental
Dimensions
5.71" x 4.17" x 2.05"
(145 x 106 x 52 mm)
Weight
5.61 oz (159 g)
Certification
FCC, UL/cUL, ICES-003, RSS210,
Wi-Fi (IEEE 802.11a/b/g/draft n),
WPA2™, Wi-Fi Protected Setup™
Power
12V, 1A
Operating Temp.
32 to 104ºF (0 to 40ºC)
Storage Temp.
-4 to 140ºF (-20 to 60ºC)
Operating Humidity
10 to 85% Noncondensing
Storage Humidity
5 to 90% Noncondensing
Specifications are subject to change without notice.
Page 17 / 35
Appendix C
Warranty Information
14
Wireless-N Ethernet Bridge with Dual-Band
Appendix C:
Warranty Information
Limited Warranty
Linksys warrants this Linksys hardware product against
defects in materials and workmanship under normal
use for the Warranty Period, which begins on the date of
purchase by the original end-user purchaser and lasts for
the period specified below:
One (1) year for new product
Ninety (90) days for refurbished product
Your exclusive remedy and Linksys’ entire liability under
this limited warranty will be for Linksys, at its option, to
(a) repair the product with new or refurbished parts,
(b) replace the product with a reasonably available
equivalent new or refurbished Linksys product, or (c) refund
the purchase price of the product less any rebates. Any
repaired or replacement products will be warranted for
the remainder of the original Warranty Period or thirty (30)
days, whichever is longer. All products and parts that are
replaced become the property of Linksys.
Linksys additionally warrants that any media on which
the software may be provided will be free from defects in
materials and workmanship under normal use for a period
of ninety (90) days from the date of original purchase.
Your exclusive remedy and Linksys’ entire liability under
this limited warranty will be for Linksys, at its option, to
(a) replace the software media, or (b) refund the purchase
price of the software media.
Exclusions and Limitations
This limited warranty does not apply if: (a) the product
assembly seal has been removed or damaged, (b) the
product has been altered or modified, except by Linksys,
(c) the product damage was caused by use with non-
Linksys products, (d) the product has not been installed,
operated, repaired, or maintained in accordance with
instructions supplied by Linksys, (e) the product has
been subjected to abnormal physical or electrical stress,
misuse, negligence, or accident, (f) the serial number on
the Product has been altered, defaced, or removed, or
(g) the product is supplied or licensed for beta, evaluation,
testing or demonstration purposes for which Linksys does
not charge a purchase price or license fee.
EXCEPT FOR THE LIMITED WARRANTY ON MEDIA SET FORTH
ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ALL SOFTWARE PROVIDED BY LINKSYS
WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING
THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY
OF ANY KIND. Without limiting the foregoing, Linksys does
not warrant that the operation of the product or software
will be uninterrupted or error free. Also, due to the
continual development of new techniques for intruding
upon and attacking networks, Linksys does not warrant
that the product, software or any equipment, system or
network on which the product or software is used will be
free of vulnerability to intrusion or attack. The product
may include or be bundled with third party software or
service offerings. This limited warranty shall not apply to
such third party software or service offerings. This limited
warranty does not guarantee any continued availability
of a third party’s service for which this product’s use or
operation may require.
TO THE
EXTENT
NOT
PROHIBITED
BY
APPLICABLE
LAW,
ALL
IMPLIED
WARRANTIES
AND
CONDITIONS
OF
MERCHANTABILITY,
SATISFACTORY
QUALITY
OR
FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO
THE DURATION OF THE WARRANTY PERIOD. ALL OTHER
EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS
AND WARRANTIES ARE DISCLAIMED. Some jurisdictions
do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This
limited warranty gives you specific legal rights, and you
may also have other rights which vary by jurisdiction.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW,
IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST
DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES,
REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING
NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE
OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR
ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT
OR SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
TO THE EXTENT
NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU
FOR THE PRODUCT.
The foregoing limitations will apply
even if any warranty or remedy provided under this limited
warranty fails of its essential purpose. Some jurisdictions
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or
exclusion may not apply to you.
Obtaining Warranty Service
If
you
have
a
question
about
your
product
or
experience
a
problem
with
it,
please
go
to
www.linksysbycisco.com/support
where you will find a
variety of online support tools and information to assist
you with your product. If the product proves defective
during the Warranty Period, contact Linksys Technical
Support for instructions on how to obtain warranty service.
The telephone number for Linksys Technical Support in
your area can be found in the product User Guide and
at
www.linksysbycisco.com
. Have your product serial
number and proof of purchase on hand when calling. A
Page 18 / 35
Appendix C
Warranty Information
15
Wireless-N Ethernet Bridge with Dual-Band
DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO
PROCESS WARRANTY CLAIMS. If you are requested to
return your product, you will be given a Return Materials
Authorization (RMA) number. You are responsible for
properly packaging and shipping your product to Linksys
at your cost and risk. You must include the RMA number
and a copy of your dated proof of original purchase when
returning your product. Products received without a RMA
number and dated proof of original purchase will be
rejected. Do not include any other items with the product
you are returning to Linksys. Defective product covered
by this limited warranty will be repaired or replaced and
returned to you without charge. Customers outside of
the United States of America and Canada are responsible
for all shipping and handling charges, custom duties,
VAT and other associated taxes and charges. Repairs or
replacements not covered under this limited warranty will
be subject to charge at Linksys’ then-current rates.
Technical Support
This
limited
warranty
is
neither
a
service
nor
a
support contract.
Information about Linksys’ current
technical
support
offerings
and
policies
(including
any
fees
for
support
services)
can
be
found
at
www.linksysbycisco.com/support
.
This limited warranty is governed by the laws of the
jurisdiction in which the Product was purchased by you.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
Page 19 / 35
Appendix D
Regulatory Information
16
Wireless-N Ethernet Bridge with Dual-Band
Appendix D:
Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment or
devices
Connect the equipment to an outlet other than the
receiver’s
Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
For operation within the 5.15 ~ 5.25GHz frequency range,
it is restricted to indoor environments.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. End users
must follow the specific operating instructions for satisfying
RF exposure compliance. To maintain compliance with
FCC RF exposure compliance requirements, please follow
operation instruction as documented in this manual.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20cm between the radiator and your
body.
The
availability
of
some
specific
channels
and/or
operational frequency bands is country dependent
and is firmware programmed at the factory to match
the intended destination. The firmware setting is not
accessible by the end user.
Safety Notices
Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
Do not use this product near water, for example, in a
wet basement or near a swimming pool.
Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.
Use
only
with
UL-listed
Information Technology
Equipment (ITE).
WARNING:
This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
Industry Canada Statement
This Class B digital apparatus complies with Canadian
ICES-003 and RSS210.
Operation is subject to the following two conditions:
This device may not cause interference and
1.
This
device
must
accept
any
interference,
including
2.
interference that may cause undesired operation of
the device.
Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying
RF exposure compliance. To maintain compliance with
IC RF exposure compliance requirements, please follow
operation instruction as documented in this manual.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Restrictions in the 5 GHz Band
The
device
for
the
band
5150-5250
MHz
is
only
1.
for indoor usage to reduce potential for harmful
interference to co-channel mobile satellite systems.
This
device
has
been
designed
to
operate
with
an
2.
antenna having a maximum gain of 1.58 dBi and
1.45 dBi at 2.4 GHz and 5 GHz respectively.
Antenna
having a higher gain is strictly prohibited per
Page 20 / 35
Appendix D
Regulatory Information
17
Wireless-N Ethernet Bridge with Dual-Band
regulations of Industry Canada. The required antenna
impedance is 50 ohms.
The
maximum
antenna
gain
(please
see
the
3.
table below) permitted (for devices in the bands
5250-5350 MHz and 5470-5725 MHz) to comply with
the E.I.R.P. limit:
No.
Antenna
Type
For 2.4
GHz
Gain
(dBi)
For 5
GHz
Gain
(dBi)
Antenna
Connector
1
PIFA
1.58
1.45
N/A
2
Printed
1.58
1.45
N/A
3
PIFA
1.58
1.45
N/A
Because high power radars are allocated as primary users
(meaning they have priority) in 5250-5350 MHz and
5650-5850 MHz, these radars could cause interference
and/or damage to licensed exempt LAN devices.
Additional requirements for the band 5600-5650 MHz:
Until further notice, devices subject to this Section shall
not be capable of transmitting in the band 5600-5650 MHz,
so that Environment Canada weather radars operating in
this band are protected.
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme aux
normes NMB-003 et RSS210 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
il ne doit pas produire de brouillage et
1.
il
doit
accepter
tout
brouillage
radioélectrique
reçu,
2.
même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif.
Avis d’Industrie Canada concernant l’exposition
aux radiofréquences :
Ce matériel est conforme aux limites d’exposition aux
radiofréquences établies par Industrie Canada pour un
environnement non contrôlé. L’opérateur doit suivre les
instructions d’utilisation décrites dans le présent manuel
afin de maintenir la conformité de l’installation.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Restrictions dans la bande 5 GHz
L’appareil pour la bande de 5 150 à 5 250 MHz est conçu
1.
pour usage à l’intérieur seulement afin de réduire le
potentiel d’interférences pour les systèmes mobiles
par satellite qui utilisent le même canal.
Cet
appareil
est
conçu
pour
fonctionner
avec
une
2.
antenne ayant un gain maximal de 1,58 dBi à 2,4 GHz
et de 1,45 dBi à 5 GHz. Les antennes ayant un gain plus
élevé sont strictement interdites par Industrie Canada.
L’impédance d’antenne requise est de 50 ohms.
Le
tableau
ci-dessous
indique
le
gain
d’antenne
3.
maximal pour les bandes 5 250-5 350 MHz et 5 470-5
725 MHz afin d’assurer la conformité aux limites PIRE :
Type
d’antenne
Pour
gain de
2,4 GHz
(dBi)
Pour
gain de
5 GHz
(dBi)
Connecteur
d’antenne
1
PIFA
1,58
1,45
S.O.
2
À circuits
imprimés
1,58
1,45
S.O.
3
PIFA
1,58
1,45
S.O.
Du fait que les radars haute puissance ont la priorité
dans les bandes 5 250-5 350 MHz et 5 650-5 850 MHz, ils
pourraient causer des interférences ou endommager les
périphériques réseau sans fil.
Autres restrictions pour la bande 5 600-5 650 MHz : sauf
avis contraire, les périphériques concernés par cette
section ne doivent pas être capables de transmettre dans
la bande 5 600-5 650 MHz afin de protéger les radars
d’Environnement Canada qui l’utilisent.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Avis de non-responsabilité concernant les
appareils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top