19216811.liveAppendix C
Regulatory Information
18
Wireless ADSL2+ Modem Router
Australia
The following information applies if you use the product
within Australia.
Safety Notice
WARNING:
To
ensure
compliance
with
exposure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
New Zealand
The following information applies if you use the product
within New Zealand.
Telepermit Statement
The cabling between the phone port and the phone shall
not exceed 100 metres.
PTC200 General Warning
The grant of a Telepermit for any item of terminal
equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for
connection to its network.
It indicates no endorsement
of the product by Telecom, nor does it provide any sort
of warranty.
Above all, it provides no assurance that any
item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model,
nor does it imply that any product is compatible with all of
Telecom’s network services.
Wireless Connectivity Security on Cisco-Linksys
ADSL2+ Devices
Setting up the security of the wireless connection
associated with ADSL2+ device is the user’s responsibility.
Telecom will take no responsibility for charges made to
user’s accounts due to poorly organized wireless security
allowing unknown users to connect to the Internet via this
device.
Do not complain to the Telecom Fault Service or
Jetstream Helpdesk should this occur.
General Warning for Cisco-Linksys ADSL2+
Devices and ADSL2+ Capability
This device has been tested and found suitable to connect
to the Telecom ADSL2+ capability.
This indicates only that
Telecom has accepted that this device complies with the
spectrum management plan for ADSL2+ on copper cable
and with simple voiceband compatibility tests included
in PTC273.
It does not indicate that this device is fully
compatible with all services accessed via the ADSL2+
capability.
Contact the supplier of the device when
issues occur.
Do not call the Telecom Fault Service or the
Jetstream Helpdesk.
Cisco-Linksys ADSL2+ Devices on Long Lines
ADSL2+ devices may not achieve the type of “high speed”
operation expected when attached to a line that is longer
than intended by the ITU-T Rec. G.996.1 ADSL standard
i.e. >3 km of 0.4mm cable or a shorter cable length with
several tails or multiples.
If the device is installed in such
conditions and does not give the expected “download”
performance, then do not refer the matter to the Telecom
Fault Service or ADSL Helpdesk.
United States of America
The following information applies if you use the product
within the United States of America.
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator and your body.