1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WAG160Nv2
    5. /
  5. 5
Page 21 / 23 Scroll up to view Page 16 - 20
Appendix C
Regulatory Information
18
Wireless ADSL2+ Modem Router
Australia
The following information applies if you use the product
within Australia.
Safety Notice
WARNING:
To
ensure
compliance
with
exposure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
New Zealand
The following information applies if you use the product
within New Zealand.
Telepermit Statement
The cabling between the phone port and the phone shall
not exceed 100 metres.
PTC200 General Warning
The grant of a Telepermit for any item of terminal
equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for
connection to its network.
It indicates no endorsement
of the product by Telecom, nor does it provide any sort
of warranty.
Above all, it provides no assurance that any
item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model,
nor does it imply that any product is compatible with all of
Telecom’s network services.
Wireless Connectivity Security on Cisco-Linksys
ADSL2+ Devices
Setting up the security of the wireless connection
associated with ADSL2+ device is the user’s responsibility.
Telecom will take no responsibility for charges made to
user’s accounts due to poorly organized wireless security
allowing unknown users to connect to the Internet via this
device.
Do not complain to the Telecom Fault Service or
Jetstream Helpdesk should this occur.
General Warning for Cisco-Linksys ADSL2+
Devices and ADSL2+ Capability
This device has been tested and found suitable to connect
to the Telecom ADSL2+ capability.
This indicates only that
Telecom has accepted that this device complies with the
spectrum management plan for ADSL2+ on copper cable
and with simple voiceband compatibility tests included
in PTC273.
It does not indicate that this device is fully
compatible with all services accessed via the ADSL2+
capability.
Contact the supplier of the device when
issues occur.
Do not call the Telecom Fault Service or the
Jetstream Helpdesk.
Cisco-Linksys ADSL2+ Devices on Long Lines
ADSL2+ devices may not achieve the type of “high speed”
operation expected when attached to a line that is longer
than intended by the ITU-T Rec. G.996.1 ADSL standard
i.e. >3 km of 0.4mm cable or a shorter cable length with
several tails or multiples.
If the device is installed in such
conditions and does not give the expected “download”
performance, then do not refer the matter to the Telecom
Fault Service or ADSL Helpdesk.
United States of America
The following information applies if you use the product
within the United States of America.
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator and your body.
Page 22 / 23
Appendix C
Regulatory Information
19
Wireless ADSL2+ Modem Router
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. IEEE
802.11b or 802.11g operation of this product in the USA is
firmware-limited to channels 1 through 11.
FCC Part 68 Statement
This equipment complies with Part 68 of the FCC Rules. A
label is attached to the equipment that contains, among
other information, its FCC registration number and ringer
equivalence number. If requested, this information must
be provided to the telephone company.
This equipment uses the following USOC Jack: RJ-11.
An FCC compliant telephone cord and modular plug
is provided with this equipment. This equipment is
designed to be connected to the telephone network or
premises wiring using a compatible modular jack, which
is FCC Part 68 compliant. Connection to the telephone
network should be made by using the standard modular
telephone jack.
The REN is useful to determine the quantity of devices
that may be connected to the telephone line and still have
all of those devices ring when your telephone number is
called. In most, but not all areas, the sum of RENs should
not exceed 5. To be certain of the number of devices that
may be connected to the line, as determined by the total
RENs, contact the telephone company to determine the
maximum REN for the calling area.
If this equipment causes harm to the telephone network,
the telephone company may discontinue your service
temporarily. If advance notice is not practical, the
telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its
facilities, equipment, operations, or procedures that could
affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make the necessary modifications in order to
maintain uninterrupted service.
In the event this equipment should fail to operate
properly, disconnect the unit from the telephone line.
Try using another FCC approved device in the same
telephone jack. If the trouble persists, call the telephone
company repair service bureau. If the trouble does not
persist and appears to be with this unit, disconnect the
unit from the telephone line and discontinue use of the
unit until it is repaired. Please note that the telephone
company may ask that you disconnect the equipment
from the telephone network until the problem has been
corrected or until you are sure that the equipment is not
malfunctioning. The user must use the accessories and
cables supplied by the manufacturer to get optimum
performance from the product.
No repairs may be done by the customer. If trouble is
experienced with this equipment, please contact your
authorized support provider for repair and warranty
information. If the trouble is causing harm to the
telephone network, the telephone company may request
you remove the equipment from the network until the
problem is resolved. This equipment cannot be used on
telephone company provided coin service. Connection to
Party Line Service is subject to state tariffs.
Safety Notices
WARNING:
To reduce the risk of fire, use only
No.26 AWG or larger telecommunication line
cord.
WARNING:
Do not use this product near water,
for example, in a wet basement or near a
swimming pool.
WARNING:
Avoid using this product during an
electrical storm. There may be a remote risk of
electric shock from lightning.
WARNING:
This equipment will be inoperable
when main power fails.
WARNING:
To
ensure
compliance
with
explosure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
Page 23 / 23
Appendix C
Regulatory Information
20
Wireless ADSL2+ Modem Router
Avis d’Industrie Canada concernant l’exposition aux radio-
fréquences :
Ce matériel est conforme aux limites établies par IC
en matière d’exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 20 cm entre l’antenne
et le corps de l’utilisateur.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Avis de non-responsabilité concernant les appar-
eils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
Canada
The following information applies if you use the product
within Canada.
Industry Canada Statement
This device complies with Industry Canada ICES-003 and
RSS210 rules.
Operation is subject to the following two conditions:
1.
This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device. This device has been designed to operate
with an antenna having a maximum gain of 2dBi.
Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna
impedance is 50 ohms.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the EIRP is not more than required for successful
communication.
Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Avis d’Industrie Canada
Cet appareil est conforme aux normes NMB003 et RSS210
d’Industrie Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
1.
il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif. Le dispositif a été
conçu pour fonctionner avec une antenne ayant un gain
maximum de 2 dBi. Les règlements d’Industrie Canada
interdisent strictement l’utilisation d’antennes dont le
gain est supérieur à cette limite. L’impédance requise
de l’antenne est de 50 ohms.
Afin de réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure
au niveau requis pour obtenir une communication
satisfaisante.
090605-10_20-10C-AI
3425-01414

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top