1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SRW224
    5. /
  5. 8
Page 36 / 104 Scroll up to view Page 31 - 35
28
Chapter 5: Configuring the Switch through the Web Utility
System Information
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Dynamic Address
The Dynamic Address Table contains the MAC addresses learned by monitoring the source address for traffic
entering the switch. When the destination address for inbound traffic is found in the database, the packets
intended for that address are forwarded directly to the associated port. Otherwise, the traffic is flooded to all
ports.
Interface
. Indicates a port or lag.
MAC Address
. Physical address associated with this interface.
VLAN
. ID of configured VLAN (1-4094).
Address Table Sort Key
. You can sort the information displayed based on MAC address, VLAN or interface (port
or lag).
Dynamic Address Counts
. The number of addresses dynamically learned.
Current Dynamic Address Table
. Lists all the dynamic addresses.
Specify the search type (that is, check the Interface, MAC Address, and/or VLAN checkbox), select the method of
sorting the displayed addresses, and then click
Query
.
Static address
A static address can be assigned to a specific interface on this switch. Static addresses are bound to the
assigned interface and will not be moved. When a static address is seen on another interface, the address will be
ignored and will not be written to the address table.
Static Address Counts
. The number of manually configured addresses. The Switch allows 8,000 Static Address
Counts.
Current Static Address Table
. Lists all the static addresses.
Interface
. Port or lag associated with the device assigned a static address.
MAC Address
. Physical address of a device mapped to this interface.
VLAN
. ID of configured VLAN (1-4094).
Specify the interface, the MAC address and VLAN, then click
Add Static Address
.
Figure 5-8: Static Address Screen
Figure 5-7: Dynamic Address Screen
Page 37 / 104
29
Chapter 5: Configuring the Switch through the Web Utility
System Information
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Time Synchronization
Simple Network Time Protocol (SNTP) allows the switch to set its internal clock based on periodic updates from a
time server (SNTP or NTP). Maintaining an accurate time on the switch enables the system log to record
meaningful dates and times for event entries. If the clock is not set, the switch will only record the time from the
factory default set at the last bootup. When the SNTP client is enabled, the switch periodically sends a request for
a time update to a configured time server. You can configure up to three time server IP addresses. The switch will
attempt to poll each server in the configured sequence.
The Time Synchronization screen displays the following information.
SNTP Client
. Configures the switch to operate as an SNTP client. This requires at least one time server to be
specified in the SNTP Server field. (Default: Disabled)
Current Time
. Displays the current time.
Name
. Assign a name for the time setting.
Hours
. Set the hours for the clock.
Minutes
. Set the minutes for the clock.
Direction
. SNTP uses Coordinated Universal Time (or UTC, formerly Greenwich Mean Time, or GMT) based on the
time at the Earth’s prime meridian, zero degrees longitude. To display a time corresponding to your local time,
you must indicate the number of hours and minutes your time zone is east (after) or west (before) of UTC.
Click the SNTP Client checkbox to Enable SNTP Client. Uncheck it to disable it.
Set the name, hours and minutes using the text fields.
Set the Direction by choosing the Before-UTC or After-UTC.
Click
Submit
to save the changes.
Figure 5-9: Sys. Info - Time Synchronization Screen
Page 38 / 104
30
Chapter 5: Configuring the Switch through the Web Utility
System Information
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
CPU Performance
The CPU Performance screen displays the current percentage of processor power being used by the switch.
Logout
To logout, click the
Logout
hyper-link. Then click
OK
to proceed or
Cancel
to cancel. Then click
Yes
to close the
window or
No
to cancel.
Figure 5-10: Sys. Info - CPU Performance
Figure 5-11: Sys. Info - Logout
Page 39 / 104
31
Chapter 5: Configuring the Switch through the Web Utility
IP Config
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
IP Config
The IP Config tab includes a link to the following screen.
•
IP Address
IP Address
To manually configure IP settings, you need to set an IP address and subnet mask that is compatible with your
network. You may also need to establish a default gateway between the switch and management stations that
exist on another network segment.
An IP address may be used for management access to the switch over your network. You may also need to
establish a default gateway between the switch and management stations that exist on another network
segment.
The IP Address screen displays the following information
IP Address Mode
. Specifies whether IP functionality is enabled via manual configuration (Static), Dynamic Host
Configuration Protocol (DHCP), or Boot Protocol (BOOTP). If DHCP/BOOTP is enabled, IP will not function until a
reply has been received from the server. Requests will be broadcast periodically by the switch for an IP address.
(DHCP/BOOTP values can include the IP address, subnet mask, and default gateway.)
Host Name
. Specifies the name of the switch. Enter the name into the textfield provided, up to 255 characters
long. (Default: None)
IP Address
. Address of the VLAN interface that is allowed management access. Valid IP addresses consist of four
numbers, 0 to 255, separated by periods. (Default: 192.168.1.254)
Mask
. This mask identifies the host address bits used for routing to specific subnets.
(Default: 255.255.255.0)
Default Gateway
. IP address of the gateway router between this device and management stations that exist on
other network segments. (Default: 0.0.0.0)
Current Management Interface
. ID of the configured VLAN (1-4094, no leading zeroes). By default, all ports on
the switch are members of VLAN 1. However, the management station can be attached to a port belonging to any
VLAN, as long as that VLAN has been assigned an IP address.
Figure 5-12: IP Config - IP Address
Page 40 / 104
32
Chapter 5: Configuring the Switch through the Web Utility
IP Config
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Select the IP Address Mode using the drop-down menu. Selecting
Static
will allow you to enter a static IP
address, subnet mask and default gateway using the text field provided. Selecting
BOOTP
or
DHCP
disables
these text boxes and auto assigns an IP address.
Enter a name for each IP address using the textfield provided and the Current Management Interface using the
drop-down menu box.
Click
submit
to save the changes.
Click
Restart DHCP
to assign a new IP address using DHCP.

Rate

4.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top