Linksys SPA-841 Router Manual PDF (Setup & Configuration Guide)

Page 231 / 286 Scroll up to view Page 226 - 230

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

229

B

Voice tab > Regional page

Ring and Call Waiting Tone Spec section

Voice tab > Regional page

Control Timer Values (sec) section

Ring Waveform

Waveform for the ringing signal: Sinusoid or Trapezoid.

Default:

Trapezoid

Ring Frequency

Frequency of the ringing signal. Valid values are 10–100 (Hz).

Default:

0

Ring Voltage

Ringing voltage. 60–90 (V).

Default:

85

CWT Frequency

Frequency script of the call waiting tone. All distinctive CWTs

are based on this tone.

Default:

440@-10

Hook Flash Timer Min

Minimum on-hook time before off-hook qualifies as hook-

flash. Less than this the on-hook event is ignored. Range: 0.1–

0.4 seconds.

Default:

.1

Hook Flash Timer Max

Maximum on-hook time before off-hook qualifies as hook-

flash. More than this the on-hook event is treated as on-hook

(no hook-flash event). Range: 0.4–1.6 seconds.

Default:

.9

Callee On Hook Delay

Phone must be on-hook for at this time in sec before the

SPA9000 tears down the current inbound call. It does not

apply to outbound calls. Range: 0–255 seconds.

Default:

0

Reorder Delay

Delay after far end hangs up before reorder tone is played. 0

= plays immediately, inf = never plays. Range: 0–255

seconds.

Default:

5

Call Back Expires

Expiration time in seconds of a call back activation. Range: 0–

65535 seconds.

Default:

1800

Downloaded from

www.Manualslib.com

manuals search engine

Page 232 / 286

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

230

B

Call Back Retry Intvl

Call back retry interval in seconds. Range: 0–255 seconds.

Default:

30

Call Back Delay

Delay after receiving the first SIP 18x response before

declaring the remote end is ringing. If a busy response is

received during this time, the SPA9000 still considers the call

as failed and keeps on retrying.

Default:

.5

VMWI Refresh Intvl

Interval between VMWI refresh to the CPE.

Default:

0

Interdigit Long Timer

Long timeout between entering digits when dialing. The

interdigit timer values are used as defaults when dialing. The

Interdigit_Long_Timer is used after any one digit, if all valid

matching sequences in the dial plan are incomplete as dialed.

Range: 0–64 seconds.

Default:

10

Interdigit Short Timer

Short timeout between entering digits when dialing. The

Interdigit_Short_Timer is used after any one digit, if at least

one matching sequence is complete as dialed, but more

dialed digits would match other as yet incomplete

sequences. Range: 0–64 seconds.

Default:

3

CPC Delay

Delay in seconds after caller hangs up when the SPA9000

starts removing the tip-and-ring voltage to the attached

equipment of the called party. Range: 0–255 seconds.

SPA9000 has had polarity reversal feature since release 1.0

which can be applied to both the caller and the callee end.

This feature is generally used for answer supervision on the

caller side to signal to the attached equipment when the call

has been connected (remote end has answered) or

disconnected (remote end has hung up). This feature should

be disabled for the called party (in other words, by using the

same polarity for connected and idle state) and the CPC

feature should be used instead.

Without CPC enabled, reorder tone is played after a

configurable delay. If CPC is enabled, dial tone is played

when tip-to-ring voltage is restored Resolution is 1 second.

Default:

2

Downloaded from

www.Manualslib.com

manuals search engine

Page 233 / 286

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

231

B

Voice tab > Regional page

Vertical Service Activation Codes section

NOTE

Vertical Service Activation Codes are automatically appended to the dial-plan.

There is no need to include them in dial-plan, although no harm is done if they are

included.

CPC Duration

Duration in seconds for which the tip-to-ring voltage is

removed after the caller hangs up. After that, tip-to-ring

voltage is restored and dial tone applies if the attached

equipment is still off-hook. CPC is disabled if this value is set

to 0. Range: 0 to 1.000 second. Resolution is 0.001 second.

Default:

0

(CPC disabled)

Call Return Code

This code calls the last caller.

Default:

*69

Call Redial Code

Redials the last number called.

Default:

*07

Blind Transfer Code

Begins a blind transfer of the current call to the extension

specified after the activation code.

Default:

*98

Call Back Act Code

Starts a callback when the last outbound call is not busy.

Default:

*66

Call Back Deact Code

Cancels a callback.

Default:

*86

Call Back Busy Act Code

Starts a callback when the last outbound call is busy.

Default:

*05

Cfwd All Act Code

Forwards all calls to the extension specified after the

activation code.

Default:

*72

Cfwd All Deact Code

Cancels call forwarding of all calls.

Default:

*73

Cfwd Busy Act Code

Forwards busy calls to the extension specified after the

activation code.

Default:

*90

Downloaded from

www.Manualslib.com

manuals search engine

Page 234 / 286

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

232

B

Cfwd Busy Deact Code

Cancels call forwarding of busy calls.

Default:

*91

Cfwd No Ans Act Code

Forwards no-answer calls to the extension specified after the

activation code.

Default:

*92

Cfwd No Ans Deact

Code

Cancels call forwarding of no-answer calls.

Default:

*93

Cfwd Last Act Code

Forwards the last inbound or outbound calls to the extension

specified after the activation code.

Default:

*63

Cfwd Last Deact Code

Cancels call forwarding of the last inbound or outbound calls.

Default:

*83

Block Last Act Code

Blocks the last inbound call.

Default:

*60

Block Last Deact Code

Cancels blocking of the last inbound call.

Default:

*80

Accept Last Act Code

Accepts the last outbound call. It lets the call ring through

when do not disturb or call forwarding of all calls are enabled.

Default:

*64

Accept Last Deact Code

Cancels the code to accept the last outbound call.

Default:

*84

CW Act Code

Enables call waiting on all calls.

Default:

*56

CW Deact Code

Disables call waiting on all calls.

Default:

*57

CW Per Call Act Code

Enables call waiting for the next call.

Default:

*71

CW Per Call Deact Code

Disables call waiting for the next call.

Default:

*70

Block CID Act Code

Blocks caller ID on all outbound calls.

Default:

*67

Block CID Deact Code

Removes caller ID blocking on all outbound calls.

Default:

*68

Block CID Per Call Act

Code

Blocks caller ID on the next outbound call.

Default:

*81

Downloaded from

www.Manualslib.com

manuals search engine

Page 235 / 286

SPA9000 Field Reference

Voice tab

SPA9000 Voice System Administration Guide

233

B

Block CID Per Call Deact

Code

Removes caller ID blocking on the next inbound call.

Default:

*82

Block ANC Act Code

Blocks all anonymous calls.

Default:

*77

Block ANC Deact Code

Removes blocking of all anonymous calls.

Default:

*87

DND Act Code

Enables the do not disturb feature.

Default:

*78

DND Deact Code

Disables the do not disturb feature.

Default:

*79

CID Act Code

Enables caller ID generation.

Default:

*65

CID Deact Code

Disables caller ID generation.

Default:

*85

CWCID Act Code

Enables call waiting, caller ID generation.

Default:

*25

CWCID Deact Code

Disables call waiting, caller ID generation.

Default:

*45

Dist Ring Act Code

Enables the distinctive ringing feature.

Default:

*26

Dist Ring Deact Code

Disables the distinctive ringing feature.

Default:

*46

Speed Dial Act Code

Assigns a speed dial number.

Default:

*74

Secure All Call Act Code

Makes all outbound calls secure.

Default:

*16

Secure No Call Act Code

Makes all outbound calls not secure.

Default:

*17

Secure One Call Act

Code

Makes the next outbound call secure. (It is redundant if all

outbound calls are secure by default.)

Default:

*18

Secure One Call Deact

Code

Makes the next outbound call not secure. (It is redundant if all

outbound calls are not secure by default.)

Default:

*19

Conference Act Code

If this code is specified, the user must enter it before dialing

the third party for a conference call. Enter the code for a

conference call.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular Linksys Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share