1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. RTP300
    5. /
  5. 6
Page 26 / 96 Scroll up to view Page 21 - 25
Broadband Router with 2 Phone Ports
18
Chapter 5: Configuring the Router
How to Access the Web-based Utility
Voice
Access to the Voice tab is restricted by your Internet phone service provider. Contact your provider for more
information.
How to Access the Web-based Utility
To access the Web-based Utility of the Router, launch Internet Explorer or Netscape Navigator, and enter the
Router’s default IP address,
192.168.15.1
, in the
Address
field. Press the
Enter
key.
The
Login
screen will appear asking you for your User name and Password. Enter
admin
in the
User Name
and
Password
fields. Then click the
Log In
button. Click the
Cancel
button to exit the
Login
screen.
Make the necessary changes through the Utility. When you have finished making changes to a screen, click the
Save Settings
button to save the changes, or click the
Cancel Changes
button to undo your changes. Help
information is shown on the right-hand side of a screen. For additional help on a tab, click
More
.
Figure 5-2: Router Login
Figure 5-1: Router’s IP
Address
Downloaded from
www.Manualslib.com
manuals search engine
Page 27 / 96
Broadband Router with 2 Phone Ports
19
Chapter 5: Configuring the Router
The Setup Tab - Basic Setup
The Setup Tab - Basic Setup
The
Basic Setup
screen is the first screen you see when you access the Web-based Utility.
Internet Setup
The Internet Setup section configures the Router for your Internet connection type. This information can be
obtained from your ISP.
Internet Connection Type
The Router supports three connection types: Obtain an IP automatically, Static IP, and PPPoE. Each
Basic Setup
screen and available features will differ depending on what kind of connection type you select.
Obtain an IP automatically
By default, the Router’s Internet Connection Type is set to
Obtain an IP automatically
, and it should be
used only if your ISP supports DHCP or you are connecting through a dynamic IP address.
Figure 5-3: Setup Tab - Basic Setup
(Obtain an IP automatically)
Downloaded from
www.Manualslib.com
manuals search engine
Page 28 / 96
Broadband Router with 2 Phone Ports
20
Chapter 5: Configuring the Router
The Setup Tab - Basic Setup
Static IP
If you are required to use a permanent IP address, then select
Static IP
.
IP Address
. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide
you with the IP Address you need to specify here.
Subnet Mask
. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your
ISP). Your ISP will provide you with the Subnet Mask.
Gateway
. Your ISP will provide you with the Default Gateway Address.
DNS 1-3
. Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.
WINS
. The Windows Internet Naming Service (WINS) converts NetBIOS names to IP addresses. If you use a
WINS server, enter that server’s IP address here. Otherwise, leave this field blank.
PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections for
end-users. If you use a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to
enable it.
User Name and Password
. Enter the User Name and Password provided by your ISP.
Connect on Demand and Keep Alive
. You can configure the Router to cut the Internet connection after it
has been inactive for a specific period of time (Idle Timeout). If your Internet connection has been terminated
due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as
soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio
Figure 5-4: Static IP
static ip address
: a fixed address
assigned to a computer or device
connected to a network.
subnet mask
: an address code that
determines the size of the network.
default gateway
: a device that forwards
Internet traffic from your local area
network.
pppoe
: a type of broadband connection
that provides authentication (username
and password) in addition to data
transport.
Downloaded from
www.Manualslib.com
manuals search engine
Page 29 / 96
Broadband Router with 2 Phone Ports
21
Chapter 5: Configuring the Router
The Setup Tab - Basic Setup
button. If you want your Internet connection to remain on at all times, enter
0
in the
Idle Timeout
field.
Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
Keep Alive and Redial Period
. This option keeps your Internet access connected indefinitely, even when it
sits idle. If you select this option, the Router will periodically check your Internet connection. If the
connection is down, then the Router will automatically re-establish the connection. To use this option, click
the radio button next to
Keep Alive
. The default Redial Period is
60
seconds.
When you are finished, click the
Save Settings
button. Then click the
Status
tab, and click the
Connect
button to start the connection.
Optional Settings
Some of these settings may be required by your ISP. Verify with your ISP before making any changes.
Host Name and Domain Name
. These fields allow you to supply a host and domain name for the Router. Some
ISPs require these names as identification. You may have to check with your ISP to see if your broadband
Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will
work.
MTU
. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network
transmission. Select
Auto
to have the Router automatically select the MTU value, or select
Manual
and enter the
value desired. It is recommended that you leave this value in the 1200 to 1500 range. For two Internet connection
types, Obtain an IP automatically and Static IP, the MTU’s default value is
1500
. For PPPoE, the MTU’s default
value is
1492
.
Network Setup
The Network Setup section allows you to change the Router’s local network settings.
NOTE:
For DSL users, if you
need to enable PPPoE support,
remember to remove any PPPoE
applications that are installed
on your PCs.
Figure 5-5: PPPoE
packet
: a unit of data sent over
a network.
Downloaded from
www.Manualslib.com
manuals search engine
Page 30 / 96
Broadband Router with 2 Phone Ports
22
Chapter 5: Configuring the Router
The Setup Tab - Basic Setup
Router IP
The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the
default values will work.
Local IP Address
. The default value is
192.168.15.1
.
Subnet Mask
. The default value is
255.255.255.0
.
Network Address Server Settings (DHCP)
These settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function.
The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address
to each computer on your network. Unless you already have one, it is highly recommended that you leave the
Router enabled as a DHCP server.
Local DHCP Server
. DHCP is enabled by factory default. If you already have a DHCP server on your network, set
the Router’s DHCP option to
Disable
. If you disable DHCP, remember to assign a static IP address to the Router.
Start IP Address
. Enter a value for the DHCP server to start with when issuing IP addresses. Because the
default IP address for the Router is 192.168.15.1, the Start IP Address must be 192.168.15. 101 or greater, but
smaller than 192.168.15.254. The default Start IP Address is
192.168.15.100
.
Number of Address
(Optional). Enter the maximum number of PCs that you want the DHCP server to assign IP
addresses to. This number cannot be greater than 253. The default is
50
.
DHCP Address Range
. The range of DHCP addresses is displayed here.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top