Page 11 / 68 Scroll up to view Page 6 - 10
5
Chapter 2: Networking Basics
The Use of IP Addresses
Broadband Router
A DHCP server can either be a designated PC on the network or another network device, such as the Router. By
default, the Router’s Internet Connection Type is
Obtain an IP automatically
(DHCP).
The PC or network device obtaining an IP address is called the DHCP client. DHCP frees you from having to assign
IP addresses manually every time a new user is added to your network.
For DSL users, many ISPs may require you to log on with a user name and password to gain access to the
Internet. This is a dedicated, high-speed connection type called Point to Point Protocol over Ethernet (PPPoE).
PPPoE is similar to a dial-up connection, but PPPoE does not dial a phone number when establishing a
connection. It also will provide the Router with a dynamic IP address to establish a connection to the Internet.
PPPoE
(
P
oint to
P
oint
P
rotocol
o
ver
E
thernet): a type of
broadband connection that provides authentication
(username and password) in addition to data transport.
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 68
6
Chapter 3: Getting to Know the Broadband Router
The Front Panel
Broadband Router
Chapter 3: Getting to Know the Broadband Router
The Front Panel
The Router’s LEDs are located on the front panel.
LEDs
Ethernet 1-4
Green. The
Ethernet
LEDs serves two purposes. If an LED is continuously lit, the Router
is connected to a device through the corresponding port (1, 2, 3, or 4). If an LED is
flashing, the Router is actively sending or receiving data over that port.
Internet1
Green. The
Internet1
LED lights up when the Router is connected to your cable or DSL
modem through the corresponding Internet port.
Internet2
Green. The
Internet2
LED lights up when the Router is connected to your cable or DSL
modem through the second Internet port.
Diag
Orange. The
Diag
LED lights up when the system is not ready. The LED goes off when
the system is ready.
System
Green. The
System
LED lights up when the Router is powered on. If the LED is flashing,
the Router is running a diagnostic test.
Figure 3-1: Front Panel
port:
the connection point on a computer or networking
device used for plugging in cables or adapters.
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 68
7
Chapter 3: Getting to Know the Broadband Router
The Back and Side Panels
Broadband Router
The Back and Side Panels
The Router’s ports and Reset button are located on the back panel of the Router.
If the Router is having problems connecting to the Internet, press the Reset button for just a
second with a paper clip or a pencil tip. This is similar to pressing the Reset button on your PC to
reboot it.
If you are experiencing extreme problems with the Router and have tried all other
troubleshooting measures, press and hold in the Reset button for 30 seconds. This will restore
the factory defaults and clear all of the Router’s settings, such as port forwarding or a new
password.
Ports
Ethernet 1-4
These four
Ethernet
ports connect to network devices, such as PCs, print servers, or additional
switches.
Internet1
The
Internet1
port connects to a cable or DSL modem.
Internet2
The
Internet2
port acts as an additional Internet port and connects to a cable or DSL modem.
Power
The
Power
port is where you will connect the included AC power cable.
Proceed to “Chapter 4: Connecting the Broadband Router.”
Internet1
Ethernet
Internet2
boot:
to start a device and cause it to
start executing instructions.
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 68
8
Chapter 4: Connecting the Broadband Router
Overview
Broadband Router
Chapter 4: Connecting the Broadband Router
Overview
To set up your network, you will need to do the following:
Connect the Router to one of your PCs according to the instructions in this chapter.
Set up and configure the Router with the setting(s) provided by your Internet Service Provider (ISP) according
to “Chapter 5: Setting up and Configuring the Broadband Router.”
The installation technician from your ISP should have left the setup information with you after installing your
broadband connection. If not, you can call your ISP to request the information. Once you have the setup
information for your specific type of Internet connection, then you can begin installation and setup of the Router.
Cable or DSL
Modem
Broadband
Router
Notebook with
Ethernet Adapter
PC with Ethernet
Adapter
Figure 4-1: Example of a Typical Network
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 68
9
Chapter 4: Connecting the Broadband Router
Connection Instructions
Broadband Router
Connection Instructions
1.
Before you begin, make sure that all of your hardware is powered off, including the Router, PCs, hubs,
switches, and cable or DSL modem.
2.
Connect one end of an Ethernet network cable to one of the Ethernet ports on the back of the Router. Connect
the other end to an Ethernet port on a network device, e.g., a PC, print server, hub, or switch.
Repeat this step to connect more PCs or other network devices to the Router.
3.
Connect your cable or DSL modem’s Ethernet cable to one of the Router’s Internet ports. If using the Internet2
port, connect a second cable to it, and the other end to the network device, e.g., modem or public server.
4.
Power on the cable or DSL modem and the other network device if using one.
5.
Connect the included AC power cable to the Router’s Power port, and then plug the power adapter into an
electrical outlet.
The System LED on the front panel will light up as soon as the power adapter is connected properly.
Proceed to “Chapter 5: Setting Up and Configuring the Broadband Router.”
Figure 4-2: Connect a PC
Figure 4-3: Connect the Internet
Figure 4-4: Connect the Power
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top