1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. E4200
    5. /
  5. 8
Page 36 / 80 Scroll up to view Page 31 - 35
26
Setting Up: Advanced
Linksys E-Series
5.
Complete the fields with information provided by your DDNS provider,
then click
Save Settings
° The
Status
field tells you what actions have
been taken°
In this example, the domain name registered with TZO°com is
BronzeEagle953.linksysnet.com
° If an Internet camera had been configured
(see “How to set up port forwarding for a single port” on page 50), you
could access the camera by typing the domain name into the address bar
of your web browser followed by the port number used for the device°
For example, if the camera in the above example used port 1024, the URL
would be:
BronzeEagle953.linksysnet.com:1024
How to clone a MAC address
On any home network, each network device has a unique
MAC
(Media Access
Control) address° Some ISPs register the MAC address of the device (usually a
router or a computer) connected directly to the modem° If your computer’s
MAC address is registered with your ISP and you do not want to re-register
the MAC address, then you can
clone
the address (assign the registered MAC
address of your previous device to your new router)° If you want to use the
MAC address from an old router that you are replacing with your new router,
you should first determine the MAC address of your old router, then manually
enter it into your new router°
NOTE
For many ISPs that provide dynamic IP addresses automatically, the
stored MAC address in the modem is reset each time you reset the
modem° If you are installing this router for the first time, reset your
modem before connecting the router to your modem° To reset your
modem, disconnect power for about one minute, then reconnect
power°
To clone a MAC address from your computer:
Setup > MAC Address Clone
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Setup
tab, then click the
MAC Address Clone
page°
3.
Click
Enabled
°
4.
Click either
Clone My PC’s MAC
or enter the 12-digit MAC address of
your old router°
5.
Click
Save Settings
°
Page 37 / 80
27
Setting Up: Advanced
Linksys E-Series
How to connect to your corporate office
using a VPN
What is a VPN, and do I need to change my router settings?
A
VPN
(Virtual
Private Network) is a network that uses a public network, such as the Internet,
to provide secure communications between a remote computer and another
network° Corporations often provide VPN access to their networks to enable
employees to work from remote offices or while traveling° Most corporate VPNs
use the Internet to provide connectivity between remote employees and the
corporate network°
For a typical VPN, the corporation installs a VPN gateway on their corporate
network° Employees authorized to work remotely connect to the VPN gateway
through the Internet using VPN software and security methods provided by
their employers° Robust security and authentication schemes ensure a secure
connection and access by only authorized users°
The default VPN settings in your router have been configured to pass through
(allow) the most common types of VPN protocols, so usually no changes are
needed°
To change your VPN passthrough settings:
Security > VPN Passthrough
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Security
tab, then click the
VPN Passthrough
page°
3.
Select each setting that you want to change°
TIP
For brief descriptions of the VPN passthrough field settings, click
Help
in the right side of the screen° More complete descriptions are
provided below°
•
IPSec Passthrough
–
IPSec
(Internet Protocol Security) is a suite of
protocols used to implement secure exchange of packets at the IP
layer° The VPN clients on the local network can establish an IPSec VPN
tunnel through the router° This option is enabled by default°
•
PPTP Passthrough
–
PPTP
(Point-to-Point Tunneling Protocol) allows
the
PPP
(Point-to-Point Protocol) to be tunneled through an IP network°
The VPN clients on the local network can establish a PPTP VPN tunnel
through the router° This option is enabled by default°
•
L2TP Passthrough
–
L2TP
(Layer 2 Tunneling Protocol) enables point-
to-point sessions using the Internet on the Layer 2 level° The VPN
clients on the local network can establish an L2TP VPN tunnel through
the router° This option is enabled by default°
4.
Click
Save Settings
to save your changes°
How to optimize your router for gaming
and voice
How does my router prioritize traffic to the Internet?
Your router has
QoS
(Quality of Service) settings that can prioritize traffic from your network out to
the Internet° Performance for demanding, real-time applications, such as online
gaming, VoIP calls, video streaming, and videoconferencing, can be improved
by configuring Internet access priorities°
QoS is applied only to traffic that is uploaded to the Internet° The router cannot
control the quality of the traffic after it reaches the Internet°
TIP
For more information on optimizing your router for online gaming,
see “Port Forwarding and Port Triggering” on page 50°
Page 38 / 80
28
Setting Up: Advanced
Linksys E-Series
To configure QOS:
Applications & Gaming > QoS
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Applications & Gaming
tab, then click the
QoS
page°
TIP
For field descriptions, click
Help
on the right side of the screen°
3.
To help manage traffic priority with devices that support WMM, select
Enabled
under
WMM Support
° Otherwise, select
Disabled
°
TIP
WMM
(Wi-Fi MultiMedia) Support is a wireless QoS feature based
on the IEEE 802°11e standard° WMM improves quality for audio,
video, and voice applications by prioritizing wireless traffic° This
feature requires that the wireless client devices in your network
also support WMM°
4.
To have the router re-send data if an error occurs, select
Disabled
under
No Acknowledgement
° Otherwise, select
Enabled
°
5.
To set access priorities for a specific device or application, select
Enabled
next to
Internet Access Priority
°
6.
In the
Category
drop-down list, select the type of item you want to set a
priority for° A list of installed items fitting that description appears°
TIP
Do not set all priorities to
High
, because all items will have the
same priority, and it would be easier to disable Internet Access
Priority for the same result°
•
Applications
and
Online Games
—Let you assign a priority for an
application or online game°
a)
Select the application or online game that you want to add from
the drop-down list, then select the priority°
b)
Click
Apply
, then click
Save Settings
°
TIP
If you want to add a new application or game, you need to know
its port and protocol information (see the application or game’s
documentation for help)°
•
MAC Address
and
Voice Device
—Let you prioritize network traffic
based on the device that is accessing the network° For example, if you
want your gaming console to have higher priority than your computer
for accessing the Internet, you can assign a higher priority to your
game console using its MAC address° We recommend giving any voice
devices a high priority°
a)
Select
MAC Address
or
Voice Device
from the drop-down list,
then enter the name of the device you want to add°
b)
Enter the device’s 12-digit MAC address, then select the priority°
c)
Click
Apply
, then click
Save Settings
°
TIP
You can often find a device’s 12-digit MAC address on the bottom
of the device° Or, if the device is connected to your network and
turned on, you can click the
Administration
tab in the router’s
browser-based utility, click the
Local Network
page, then click
DHCP Client Table
°
Page 39 / 80
29
Setting Up: Advanced
Linksys E-Series
7.
Configure
Upstream Bandwidth
°
•
To allow the router to detect the maximum, select
Auto
(default)° Auto
sets speeds in multiples of 512 Kbps°
•
To specify the maximum, select
Manual
, then select the bandwidth
you want it to use°
CAUTION
If you specify a maximum bandwidth that is too high, the router
cannot apply priorities correctly, and QoS problems may result°
8.
When you are done setting priorities, click
Save Settings
°
How to remotely change your router
settings
Why would I want to remotely change my router settings?
There may be
times when you want to change parental control settings, or change settings
for remote file access, while you are away from home°
To set up remote access:
Administration > Management
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Administration
tab, then click the
Management
page and
locate the
Remote Management Access
settings in the middle of the
screen°
3.
For
Remote Management
, select
Enabled
°
4.
For
Access via
, select
HTTP
(default) or select
HTTPS
to use
SSL
(Secure
Socket Layer) to encrypt data transmitted for higher security°
5.
To be able to upgrade your router’s firmware remotely, select
Enabled
next to
Remote Upgrade
°
6.
To allow remote access from anywhere on the Internet, select
Any IP
Address
(default) next to
Allowed Remote IP Address
° Otherwise, enter a
range of allowed IP addresses°
7.
For
Remote Management Port
, keep the setting of
8080
(default) unless
you already have a device on your network that uses port 8080 (such as
a web camera)°
8.
Click
Save Settings
at the bottom of the screen to accept your changes°
9.
Click the
Administration
tab, then click the
Management
page and take
note of the
Internet IP Address
and the
Remote Management Port
settings°
You will use this information to access your router remotely°
To access your router remotely:
1.
Open a web browser and enter the Internet address of your router, then
press
Enter
°
•
If you selected
HTTP
for your
Access via
setting, enter
http://
then the
IP address°
– OR –
•
If you selected
HTTPS
for your
Access via
setting above, enter
https://
then the IP address°
2.
Add a colon (
:
), then the
Remote Management Port
number° Example:
TIP
If you enabled the Dynamic Domain Name Service (see “How to
find your network on the Internet” on page 25), you could type in
your domain name in place of your router’s Internet IP address° For
example:
You are prompted for a user name and the password° Use the same login
information that you use to access your router at home°
After you have logged into your router’s browser-based utility remotely,
you can change any router setting, just as you would normally from your
local network°
Page 40 / 80
30
Setting Up: Advanced
Linksys E-Series
How to enable Voice over IP on your
network
Do I need to configure Voice over IP?
VoIP
(Voice over Internet Protocol) is a
technology for using the Internet as an interface for telephone communications°
To use VoIP, you need to get an account with a VoIP service provider° The VoIP
service provider typically provides you with a telephone adapter (TA) that
connects to your network° If you do not use your network to make phone calls,
you don’t need to change the default settings°
The
SIP
(Session Initiation Protocol)
ALG
(Application Layer Gateway) feature
allows SIP packets, used by some VOIP service providers, to traverse (go
through) your router’s firewall°
To configure the router for VoIP:
Administration > Management
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Administration
tab, then click the
Management
page°
3.
If your VoIP service uses SIP, select
Enabled
next to
SIP ALG
°
– OR –
If your VoIP service uses other NAT traversal solutions such as
STUN
(Session Traversal Utilities for NAT),
TURN
(Traversal Using Relay NAT), or
ICE
(Interactive Connectivity Establishment), select
Disabled
(default)°
NOTE
You may need to contact your VoIP service provider to determine
the type of NAT traversal configuration they use°
How to configure UPnP
What is UPnP?
UPnP
(Universal Plug and Play) allows devices connected
to a network to discover each other and automatically create working
configurations° Examples of UPnP-capable devices include web cameras,
online gaming applications, and VoIP devices° UPnP is enabled by default°
To configure UPnP:
Administration > Management
1.
Log into the browser-based utility (see “How to open the browser-based
utility” on page 21)°
2.
Click the
Administration
tab, then click the
Management
page°
3.
To use UPnP, select
Enabled
(default) next to
UPnP
° Otherwise, select
Disabled
°
4.
To allow changing router settings while using UPnP, select
Enabled
(default) next to
Allow Users to Configure
° Otherwise, select
Disabled
°
5.
To prevent local network users from disabling your Internet connection
through UPnP, select
Disabled
(default) next to
Allow Users to Disable
Internet Access
° Otherwise, select
Enabled
°
How to use a router as an access point
How can I use my old router as an access point?
If you have a large area to
cover with your wireless signal, or if part of your home has weak signals due to
interference, you can use your old router to extend the range of your wireless
network° This is a complex process, so this procedure assumes that you have
some networking knowledge°
TIP
Check the documentation for your old router° Some brands of
routers include either a switch on the outside of the case or a
software option to convert it to an access point° If either of these
options is available, follow your old router’s instructions to convert
it to an access point°

Rate

4.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top