Linksys BEFW11P1 Router Manual PDF (Setup & Configuration Guide)

Page 11 / 47 Scroll up to view Page 6 - 10

Etherfast

®

Wireless AP + Cable/DSL Router with PrintServer

Allocated

This field will show the IP Addresses presently allocated to the other clients on

your Network.

When you are ready to save any changes you have made, click the

Save

but-

ton. To undo any changes, click the

Cancel

button.

If you have any questions about anything on this screen, click the

Help

button

to bring up the Help window for this screen.

16

15

Instant Broadband

TM

Series

You can access this screen at any time by clicking the

DHCP

button.

A DHCP (Dynamic Host Configuration Protocol) Server allocates a valid IP

Address to the DHCP Clients that it serves, when the client device boots. The

DHCP Server also provides the Gateway and DNS addresses to the client.

Oper

ation

The DHCP Server function is enabled by default. Select Disable DHCP Server

to disable this function.

You will want to disable the DHCP Server when your Network is already using

another DHCP Server. You can only use one DHCP Server.

IP

Ad

dr

ess Rang

e

This range represents the range of IP addresses available in the DHCP pool that

can be assigned to the PCs on your Network.

DHCP Server

Downloaded from

www.Manualslib.com

manuals search engine

Page 12 / 47

18

You can access this screen at any time by clicking the

Options

button.

P

ass

w

or

d

Once a password is entered, it is required in order to change the device config-

uration. Passwords are case sensitive and can be up to eight alphanumeric char-

acters in length.

To create or change a password, enter the password in both the New password

and Verify password fields.

17

Etherfast

®

Wireless AP + Cable/DSL Router with PrintServer

Ad

ditional DNS

The fields for secondary and tertiary DNS IP Addresses are optional and

should only be completed if provided by your ISP.

N

A

T

NAT (Network Address Translation) allows PCs on your Network to share a

single external (Internet) IP Address. This IP Address is supplied by your ISP.

Use the following to determine if you need NAT:

•

For Internet access, NAT

must be enabled

unless all of the PCs on your

Network have valid external (or public) IP Addresses.

•

If the Wireless AP + Cable/DSL Router is not being used to provide shared

Internet access, NAT is not normally necessary. With NAT disabled, the

Wireless AP + Cable/DSL Router will act as a static router.

•

If NAT is disabled, the Firewall protection provided by the Wireless AP +

Cable/DSL Router is lost and the Advanced Features (Special Applications,

Access Control, Virtual Servers, DMZ, and Routing) are no longer avail-

able.

When you are ready to save any changes you have made, click the

Save

but-

ton. To undo any changes before saving, click the

Cancel

button.

If you have any questions about anything on this screen, click the

Help

button

to bring up the Help window for this screen.

Instant Broadband

TM

Series

Device Options

NOTE:

When prompted for the password,

leave the “User Name” field blank.

Downloaded from

www.Manualslib.com

manuals search engine

Page 13 / 47

20

19

Etherfast

®

Wireless AP + Cable/DSL Router with PrintServer

• SSID (Service Set Identifier).

All Wireless devices in your Network must

use the same SSID. Make sure that this field reflects the correct SSID for your

network.

• Channel No:

All Wireless devices in your Network must use the same SSID.

Make sure that this field reflects the correct channel for your network. Should

you experience any interference, you may need to experiment with different

channels to establish a better connection.

WEP

Data Pri

v

acy

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit

or 128-bit shared key algorithm, as described in the IEEE 802.11b standard.

Using a 128-bit shared key algorithm will increase network security. However,

you may experience decreased network performance when using a 128-bit

shared key algorithm.

• Off - no data encryption.

When WEP is turned off, data will not be encrypt-

ed before being transmitted, compromising security.

• 64 Bit Encryption using this key table.

For your wireless Network to utilize

WEP encryption, an encryption key must be entered fields. All wireless

devices on your Network must utilize the same encryption key and all keys

must be set identically.

• Default Key.

Select the algorithm key to be used in your 64-bit WEP-enabled

wireless Network.

• 128 Bit Encryption using this key.

For your wireless Network to utilize WEP

encryption, an encryption key must be entered fields. All wireless devices on

your Network must utilize the same encryption key and all keys must be set

identically.

The WEP keys (1 - 4) are five two-digit numerals in length and can be any

numeric combination. However, these keys must be used identically for each

point on your wireless Network.

Instant Broadband

TM

Series

You can access this screen at any time by clicking the

Wireless

button.

Any changes made to the Wireless settings must match those of the other wire-

less devices in your Network.

Conf

igur

ation

• Regulatory Domain.

It is illegal to use this device in any location outside of

the Regulatory Domain.

• Station Name.

This is the same as the Device Name that was set on the Basic

Setup screen.

Wireless

Downloaded from

www.Manualslib.com

manuals search engine

Page 14 / 47

22

Etherfast

®

Wireless AP + Cable/DSL Router with PrintServer

You can access this screen at any time by clicking the

Status

button.

The Status screen will display current data on your Wireless Access Point

Router. This screen will change if you do not enable PPPoE.

Har

d

w

ar

e

• Firmware Version.

Displays the current program code installed on the hard-

ware.

• Hardware ID.

This is utilized by Linksys to identify this device.

• NAT (Network Address Translation).

This will display your current NAT

selection.

Status

Instant Broadband

TM

Series

W

ir

eless Stations

• Access Permission.

When

Allow everyone access

, the default selection, is utilized, no check is

performed on the station’s address before allowing it to use the Wireless AP

+ Cable/DSL Router.

If you chose

Only allow access if on this list

, then a station must have an

address that appears on the address list.

• Existing Stations.

This lists the IP Addresses of those wireless stations in

your Network with access to the Wireless AP + Cable/DSL Router.

• New Station.

To add a new station to the list above, enter its address here and

click the

Add

button.

When you are ready to save any changes you have made, click the

Save

but-

ton. To undo any changes, click the

Cancel

button.

If you have any questions about anything on this page, click the

Help

button to

bring up the Help window for this screen.

21

Downloaded from

www.Manualslib.com

manuals search engine

Page 15 / 47

24

23

Etherfast

®

Wireless AP + Cable/DSL Router with PrintServer

The Advanced Options screens gives you the opportunity for further cus-

tomization of the Wireless AP + Cable/DSL Router. While the previous screens

allowed you to setup the Wireless AP + Cable/DSL Router to use, the Advanced

Options screens are optional and should not be modified without consulting

either your Network Administrator or reading this user guide. Help buttons are

provided on each screen. If you make a mistake, return to one of the previous

screens and click the Cancel button.

You can access this screen at any time by clicking the

Advanced

button and

then clicking the

Special Apps

button.

This feature is only required if you wish to use Internet applications that require

2-way communication, multiple connections, or combined TCP/UDP connec-

tions. Some examples of such applications are Internet Video-conferencing, IP

Telephony, Games Servers, and other special-purpose Servers.

Advanced Options

Special Applications

Instant Broadband

TM

Series

LAN

P

or

t

• Physical Address.

This is the physical address (Hardware MAC Address) of

the LAN Port to which an IP address has been allocated.

• IP Address.

This is the Wireless AP + Cable/DSL Router’s IP Address, as

seen by the other devices on your Network.

• Network Mask.

This is the Network Mask for the above IP Address.

• DHCP Server.

This is the status of the DHCP Server function, as selected on

the

DHCP Server

screen.

W

AN P

or

t

• Physical Address.

This is the physical address that identifies the Wireless AP

+ Cable/DSL Router to your ISP and should be used if your ISP requires you

to register this with them.

• IP Address.

This is the Wireless AP + Cable/DSL Router’s IP Address, as

seen by the other devices outside your Network.

• Network Mask.

This is the Network Mask for the above IP Address.

• PPPoE Link Status.

This shows the status of the PPPoE link, as specified

on the Basic Setup screen. (If PPPoE has not been enabled, this selection will

not appear.)

• Connection Log.

This log will only be enabled when

PPPoE (PPP Over

Ethernet)

is selected on the Basic Setup Screen and will display your connec-

tion activity. (If PPPoE has not been enabled, this selection will not appear.)

Click the

Connect

button to connect your PPPoE link.

Click the

Disconnect

button to disconnect your PPPoE link.

To reload your Connection Log data, click the

Clear Log

button.

If you have any questions about anything on this screen, click the

Help

button

to bring up the Help window for this screen.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular Linksys Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share