Page 16 / 49
Scroll up to view Page 11 - 15
KR.1N
Wireless-N Broadband Router 150Mbps / 1T1R
Chapter 5
：
Advanced Setting
This section provides details for advanced configuration of your Router. If you are not sure
about certain settings, we recommend using the default settings.
5.1 LAN Setting
MAC Address:
The Router’s physical MAC address as seen on your local network. I cannot
be changed.
IP Address:
The LAN IP Address of the Router (not your PC’s IP address). Once you modify
the IP address, you need to remember it for the Web-based Utility login.
192.168.0.1 is the
default value.
NOTE: If you have changed the IP address, you need use the new IP address
to login the Router Utility Web interface, and the default gateway setting of all
devices in the LAN must point to this IP Address to access the Internet.
Subnet Mask:
The Router Subnet Mask is to determine the network size. 255.255.255.0 is
the default value.
5.2 MAC Address Clone
Some ISPs require end-user's MAC address to access their network. This feature copies the
MAC address of your network device to the Router. Enter the MAC address to be registered in
the MAC Address field, click “Apply” to clone the Address.
MAC Address:
The MAC address to be registered with your ISP.
Clone MAC Address:
Click to register your MAC Address
Restore Default MAC Address:
Click to
restore the default hardware MAC Address.
16
www.kraun.it
Page 17 / 49
KR.1N
Wireless-N Broadband Router 150Mbps / 1T1R
5.3 DNS Settings
DNS is short for Domain Name System (or Service), an Internet service that translates domain
names into IP addresses. Normally the IP Addresses of these servers are auto-assigned by
your ISP. If for whatever reasons your need to manually enter these addresses consult your
Internet Service Provider for details.
DNS Setting:
Click the checkbox to enable the DNS server. The Router will forward DNS
requests to these servers.
Primary DNS Address
: Enter the IP Address provided by your ISP.
Secondary DNS Address:
Enter the IP Address provided by your ISP.
17
www.kraun.it
Page 18 / 49
KR.1N
Wireless-N Broadband Router 150Mbps / 1T1R
5.4. WAN Settings
Select the connection method advised by your ISP.
5.4.1 PPPoE
Account:
Enter Account or User Name provided by your ISP.
Password:
Enter the Password provided by your ISP.
MTU:
Maximum Transmission Unit. It is the size of largest datagram that can be sent over a
network. The default value is 1460.
Do NOT
modify it unless necessary.
Service Name:
It is defined as a set of characteristics that are applied to a PPPoE connection.
Enter it if provided.
Do NOT
modify it unless necessary.
AC Name:
Enter it if provided.
Do NOT
modify it unless necessary.
Connect Automatically:
Connect automatically to the Internet after rebooting the system or
connection failure.
Connect Manually:
Connect to the Internet by the user manually.
Connect on Demand:
Re-establish your connection to the Internet after the specific time
(Max Idle Time). Zero means you are always connected or else enter the time in minutes to
elapse before you want to disconnect from the Internet.
Connect on Fixed Time:
Connect to the Internet during the time period specified.
18
www.kraun.it
Page 19 / 49
KR.1N
Wireless-N Broadband Router 150Mbps / 1T1R
5.4.2 Static IP
IP Address:
Here enter the WAN IP Address provided by your ISP.
Subnet Mask:
Enter the WAN Subnet Mask here.
Gateway:
Enter the WAN Gateway Address here.
Primary DNS Server:
Enter the Primary DNS Server Address provided by your ISP.
Secondary DNS Server:
Enter the Secondary DNS Server Address.
5.4.3 L2TP
L2TP Server IP:
Enter the Server IP Address provided by your ISP.
User Name:
Enter the L2TP User Name.
Password:
Enter the L2TP Password.
MTU:
Maximum Transmission Unit, you may need to change it for optimal performance with
your specific ISP. 1460 is the default MTU.
Address Mode:
Select “Static” if your ISP supplies you with the IP address, Subnet Mask,
and Gateway Address. In most cases, select Dynamic.
IP Address:
Enter the L2TP IP Address supplied by your ISP.
Subnet Mask:
Enter the Subnet Mask supplied by your ISP.
Default Gateway:
Enter the Default Gateway Address supplied by your ISP.
19
www.kraun.it
Page 20 / 49
KR.1N
Wireless-N Broadband Router 150Mbps / 1T1R
5.4.4 PPTP
PPTP Server IP:
Enter the Server IP Address provided by your ISP.
User Name:
Enter the PPTP User Name provided by your ISP.
Password:
Enter the PPTP Password provided by your ISP.
Address Mode:
Select “Static” if your ISP supplies you with the IP address, Subnet Mask,
and Gateway Address. In most cases, select Dynamic.
IP Address:
Enter the PPTP IP address supplied by your ISP.
Subnet Mask:
Enter the Subnet Mask supplied by your ISP.
Default Gateway:
Enter the Default Gateway supplied by your ISP.
5.5 Save Connection Settings
Once all details in either of the above configuration screens have been entered, click ‘Apply’.
The Router will check for any conflicting entries. If no errors are found, the Router will reboot
and attempt to connect to the Internet using the settings provided.
20
www.kraun.it
19216811.live