Page 6 / 24 Scroll up to view Page 1 - 5
Page 6
SPI Firewall
Your modem is equipped with a firewall
that will protect your network from a
wide array of common hacker attacks
including:
IP Spoofing, Land Attack, Ping of Death
(PoD), Denial of Service (DoS), IP with
zero length, Smurf Attack, TCP Null Scan,
SYN f lood, UDP f looding, Tear Drop
Attack, ICMP defect, RIP defect, and
fragment f looding.
Universal Plug-and-Play (UPnP)
Compatibility
UPnP (Universal Plug-and-Play) is a
technology that offers seamless
operation of voice messaging,
video messaging, games, and other
applications that are UPnP-compliant.
USB/3g/Charge Ports
Your modem is equipped with two USB
ports. One on the side of the modem
for storage or for charging USB devices
such as mobile phones or for plugging
in a 3G device; the second USB slot
is situated in the back of the modem
for 3G USB modems. The Storage port
currently supports FAT16/32 & NTFS
USB Mass Storage Devices. With a mass
storage device connected you can
easily share your files to anyone on the
network.
The ‘Charge’ port will supply a maximum
5V 500mA. Connecting a USB device
which requires more than 500mA may
result in damage to your equipment.
QoS
QoS (Quality of Service) limits the traffic
being sent from the modem (upstream)
when using VoIP at the same time.
If QoS is disabled, the quality of the
VoIP call can suffer due to excessive
traffic from another source, such as a
PC. When QoS is enabled, it limits the
upstream traffic and sets it aside for
VoIP, increasing the call quality.
Virtual Server
If you have a fixed IP address, you can
set the modem to act as a virtual host
for network address translation. Remote
users access various services at your
site using a constant IP address. Then,
depending on the requested service
(or port number), the modem can route
the request to the appropriate server
(at another internal IP address).This
secures your network from direct attack
by hackers, and provides more f lexible
management by allowing you to change
internal IP addresses without affecting
outside access to your network.
Support for VPN Pass-Through
If you connect to your office network
from home using a VPN connection,
your modem will allow your VPN-
equipped computer to pass through
the modem and to your office network.
This modem supports 1 VPN session at
any one time
C
Chapter 2
:
Product Overview
About BoB Lite
TM
4 port integrated wireless modem
Page 7 / 24
Page 7
This modem supports three of the most
commonly used VPN protocols – PPTP,
L2TP, and IPSec. The VPN protocols
supported by the modem are brief ly
described below.
Point-to-Point Tunneling Protocol –
Provides a secure tunnel for remote
client access to a PPTP security
gateway. PPTP includes provisions for
call origination and flow control required
by ISPs.
L2TP merges the best features of PPTP
and L2F – Like PPTP, L2TP requires that
the ISP’s modems support the protocol.
IP Security – Provides IP network-layer
encryption. IPSec can support large
encryption networks (such as the
Internet) by using digital certificates for
device authentication.
Wired & Wireless LAN
The modem provides access for up to 4
by 10/100 Mbps wired devices and up to
an additional 32 wireless devices, making
it easy to create a network in small
offices or homes. 802 11b, 802 11g & 802
11n wireless standards are supported.
Computer Filter Rule
For added security, you can set up a
list of MAC addresses (unique client
identifiers) that are allowed access to
your network Every computer has its
own MAC address. Simply enter these
MAC addresses into a list using the
web-based user interface and you can
control access to your network.
WEP, WPA and WPA 2
Encryption protocols
The modem features WPA2, which is
the second generation of the WPA-
based 802 11i standard. It offers a higher
level of wireless security by combining
advanced network authentication and
stronger Advanced Encryption Standard
(AES) encryption methods. It also
supports the legacy security standard
called Wired Equivalent Privacy (WEP) in
order to allow you to activate security
with any legacy devices you may have
on your network.
VLAN
VLAN (Virtual Local Area Network) adds
the ability to manage multiple networks
with the one modem. The modem is
designed to be placed on a desktop.
All of the cables exit from the rear of
the modem for better organisation
and utility. The LED indicators are easily
visible on the front of the modem to
provide you with information about
network activity and status.
Chapter 2
:
Product Overview
About BoB Lite
TM
4 port integrated wireless modem
Page 8 / 24
Page 8
C
Chapter 3
:
Knowing BoB Lite
TM
Knowing your
BoB Lite
TM
4 port integrated wireless modem
Front Panel
1.
ADSL SYNC LED
The ADSL LED will light up yellow
indicating no ADSL sync. Once line
sync
is established the LED will light
up blue.
Off - No ADSL connection
On - ADSL link is up and connected
2. Internet LED
The Internet LED shows you when
the router is connected to the
Internet. If the LED is off or yellow
the router is NOT connected to the
Internet.
Off – Not connected to Internet
On – Connected to internet
3. LAN Status LED
When a computer is properly
connected to the LAN port on
the rear of the router, the LED
shown here will light. A solid light
means a computer or a network-
enabled device is connected. When
information is being sent over the
port, the LED blinks rapidly.
Off - Your computer is not
connected
On - Your computer is connected
4. Wireless Status LED
The Wireless status LED shows
you when the router’s wireless is
enabled.
On - Wireless enabled
Off - Wireless is disabled
5. Storage/3G
When a USB mass storage device
is connected to this modem, this
light will illuminate to inform you the
attached storage device is ready for
use. This modem also accepts a 3G
wireless USB modem service.
On – Attached USB Mass Storage or
3G Device connected and ready for
use
Off – No attached USB Mass Storage
or 3G Device
6. Phone Status LED
The phone light indicates that your
Netphone account has successfully
registered on the network.
On - VoIP registered successfully
Off - No VoIP activity
1
2
3
4
5
6
Page 9 / 24
Page 9
The following provides an easy step-by-step hardware installation guide.
All the modem settings have been organised for you. Simply follow all the steps to
successfully connect to the internet.
Before you begin, please check the following items have been included.
Get BoB Lite
TM
Ready
• Connect the power adaptor to the power port on the back of
BoB Lite
TM
and plug it
into an electrical outlet.
• Connect one end of a white telephone cable to the grey ‘ADSL’ port on the back
of BoB Lite
TM
and then connect the other end to the ‘ADSL’ port on the Line Filter.
• Connect the Line Filter to your telephone wall socket using the phone cable
attached to the ‘Line’ side of the filter.
• Switch
BoB Lite
TM
on and wait a few minutes.
If you have an active iiNet DSL connection BoB Lite
TM
will automatically start talking to
iiNet’s servers. BoB Lite
TM
will retrieve your login details and other settings during this
time, so please leave BoB Lite
TM
connected and give him some time to set himself
up. If you are waiting for your iiNet DSL service to be activated then BoB Lite
TM
will be
unable to connect to the internet until your application for DSL is complete.
Note:
If you have Naked DSL, you do not need to use the Line Filter. Simply connect
your phone line directly into the ‘ADSL’ port on the back of BoB Lite
TM
Chapter 4
:
Connection & Configuration
Connect & Configure
your
BoB Lite
TM
BoB Lite
TM
Power Pack
Line Filter
Ethernet
Cable
Phone Cable
x 2
User Manual
Quick Insta l Guide
Wireless Setup
Guide
Wirele s
Setup
Guide
Wirele s
Setup
Guide
Power Cable
Phone Cable
Line Filter
Page 10 / 24
Page 10
Connecting to
BoB Lite
TM
How would you like to connect your computer to BoB Lite
TM
? You can connect
multiple computers and laptops using the methods below.
Wireless
All BoB Lite
TM
units are enabled for wireless connection by default. Please refer to
Wireless Setup Guide for instructions on setting up wireless and ensuring the wireless
connection is secure.
Using the supplied ethernet cable
• Plug the yellow Ethernet cable into one of the yellow ports on the back of
BoB
Lite
TM
.
• Plug the other end into your computer or laptop’s Ethernet port.
Your computer will start talking to BoB Lite
TM
within a few moments.
How do you plan on making calls now that you have BoB Lite
TM
?
Just VoIP (Naked DSL Customers)
If you only plan to use VoIP, you’ll need to plug in your own handset into the ‘phone’
port.
Just Your Standard Phone Line (PSTN – Doesn’t Work With Naked)
If you just want to use your regular phone line to make phone calls:
• Plug the additional phone cable that came with BoB Lite
TM
into the ‘Phone’ port on
your line filter.
• Plug the other end into the black ‘pstn failover’ port on BoB Lite
TM
.
Chapter 4
:
Connection & Configuration
Connect & Configure
your
BoB Lite
TM
C
Power Cable
Phone Cable
Line Filter
Ethernet Cable

Rate

4.5 / 5 based on 2 votes.

Popular iiNet Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top