1. Home
    2. /
  2. Manuals
    3. /
  3. Hitron Technologies
    4. /
  4. CVW-30360
    5. /
  5. 8
Page 36 / 113 Scroll up to view Page 31 - 35
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
36
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
36
HITRON CGN2 USER’S GUIDE
WAN Information
WAN Address
This field displays the CGN2’s IP address on the WAN
(Wide Area Network) interface.
Subnet Mask
This field displays the CGN2’s WAN subnet mask.
Gateway Address
This field displays the address of the device on the WAN
to which the CGN2 is connected.
DNS Server
This field displays the Domain Name Servers that the
CGN2 uses to resolve domain names into IP addresses.
Uptime
This displays the number of hours, minutes and seconds
that the CGN2 has been connected to another device over
the WAN interface.
Traffic Count
This displays the number of bytes received and sent on
the WAN interface.
Wireless Information
SSID
This displays the wireless network’s Service Set Identifier.
This is the name of the wireless network, to which wireless
clients connect.
Wireless Mode
This displays the type of wireless network that the CGN2
is using.
Channel
This displays the wireless channel on which the CGN2 is
transmitting and receiving.
Security Type
This displays the type of security the CGN2’s wireless
network is currently using.
Cipher type
This displays the type of encryption that the wireless
network’s security is using:
TKIP
displays if it is using the Temporal Key Integrity
Protocol.
AES
displays if it is using the Advanced Encryption
Standard.
TKIP and AES
displays if it allows clients using either
encryption type to connect to the CGN2.
SSID MAC
This displays the Media Access Control (MAC) address of
the wireless module, to which wireless clients connect.
LAN Status
MAC Address
This displays the Media Access Control (MAC) address of
the CGN2’s Ethernet module. This is the module to which
you connect through the
LAN
ports.
Table 8:
The Status > System Info Screen (continued)
Page 37 / 113
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
37
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
37
HITRON CGN2 USER’S GUIDE
2.3
THE INITIALIZATION SCREEN
This screen displays the steps successfully taken to connect to the Internet over the
CABLE
connection.
Use this screen for troubleshooting purposes to ensure that the CGN2 has
successfully connected to the Internet; if an error has occurred you can identify the
stage at which the failure occurred.
NOTE:
This screen displays when you first log in to the CGN2.
Click
Status
>
Initialization
. The following screen displays.
Figure 8:
The Status > Initialization Screen
Private LAN IP
Address
This displays the IP address of the CGN2’s Ethernet
module. This is the IP address you use to connect with the
CGN2’s admin interface via the
LAN
ports.
Subnet Mask
This displays the CGN2’s LAN subnet mask.
Uptime
This displays the number of hours, minutes and seconds
that the CGN2 has been connected to another device over
the LAN interface.
Traffic Count
This displays the number of bytes received and sent on
the LAN interface.
Table 8:
The Status > System Info Screen (continued)
Page 38 / 113
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
38
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
38
HITRON CGN2 USER’S GUIDE
For each step:
Process
displays when the CGN2 is attempting to complete a connection step.
Success
displays when the CGN2 has completed a connection step.
2.4
THE CM STATUS SCREEN
Use this screen to discover information about:
The nature of the upstream and downstream connection between the CGN2 and
the device to which it is connected through the
CABLE
interface.
IP details of the CGN2’s WAN connection.
You can also configure the CGN2’s downstream center frequency.
Click
Status
>
CM Status
. The following screen displays.
Page 39 / 113
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
39
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
39
HITRON CGN2 USER’S GUIDE
Figure 9:
The Status > CM Status Screen
The following table describes the labels in this screen.
Table 9:
The Status > CM Status Screen
CM Configuration File
Name
This displays the name of the configuration file that the
CGN2 downloaded from your service provider. This file
provides the CGN2 with the service parameter data that
it needs to perform its functions correctly.
Network Access
This displays whether or not your service provider allows
you to access the Internet over the
CABLE
connection.
Permitted
displays if you can access the Internet.
Denied
displays if you cannot access the Internet.
Tune Channel
Page 40 / 113
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
40
Version 2.0, February 2012. Copyright
2012 Hitron Technologies
40
HITRON CGN2 USER’S GUIDE
Downstream Frequency
This displays the center frequency in Megahertz (MHz)
at which the CGN2 connects over the
CABLE
interface.
If you want the CGN2 to use a different center
frequency, enter it in the field and click
Apply
.
NOTE:
Do not change the frequency unless you have a
good reason to do so.
Upstream ID
This displays the ID number of the channel on which the
upstream signal is to be transmitted. When an upstram
connection cannot be made on the specified channel,
the CGN2 attempts to connect on the next channel.
If you want the CGN2 to attempt to connect on a
different channel, enter it in the field and click
Apply
.
NOTE:
Do not change the channel unless you have a
good reason to do so.
Downstream
NOTE:
The downstream signal is the signal transmitted to the CGN2.
Frequency (MHz)
This displays the actual frequency in Megahertz (MHz)
of each downstream data channel to which the CGN2 is
connected.
Modulation
This displays the type of modulation that each
downstream channel uses.
Signal Power (dBmV)
This displays the power of the signal of each
downstream data channel to which the CGN2 is
connected, in dBmV (decibels above/below 1 millivolt).
Signal Noise Ratio
(dB)
This displays the Signal to Noise Ratio (SNR) of each
downstream data channel to which the CGN2 is
connected, in dB (decibels).
Upstream
NOTE:
The upstream signal is the signal transmitted from the CGN2.
Frequency (Hz)
This displays the frequency in Herz (Hz) of each
upstream data channel to which the CGN2 is connected.
Bandwidth (KSym/
sec)
This displays the bandwidth of each upstream data
channel to which the CGN2 is connected (in thousands
of symbols per second).
Table 9:
The Status > CM Status Screen (continued)

Rate

3.5 / 5 based on 2 votes.

Popular Hitron Technologies Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top