Page 26 / 114
Scroll up to view Page 21 - 25
Version 1.1, 08/2013. Copyright
2013 Hitron Technologies
26
Hitron CGN3 User’s Guide
Click
Admin
>
Device Reset
. In the screen that displays, click the
Factory
Reset
button.
After the operation, The CGN3 turns off and on again, using its factory default
settings.
NOTE:
Depending on your CGN3’s previous configuration, you may need to re-
configure your computer’s IP settings; see
IP Address Setup
on page
22
.
Page 27 / 114
Version 1.1, 08/2013. Copyright
2013 Hitron Technologies
27
Hitron CGN3 User’s Guide
2
Setup Wizard
This chapter describes the CGN3’s setup wizard, which displays when you click
Setup Wizard
in the toolbar. It contains the following sections:
Setup Wizard Overview
on page
27
Setting Password
on page
27
LAN Settings
on page
28
Wireless Settings
on page
30
Summary
on page
31
2.1
Setup Wizard Overview
Your CGN3 possess a setup wizard that allows you to rapidly configure its most
important settings, including password, LAN and wireless settings.
2.2
Setting Password
Use this screen to create a new password for the CGN3’s user interface.
NOTE:
It is strongly recommended that you change the CGN3’s password from its
factory default.
Click
Setup Wizard
. The following screen displays.
Page 28 / 114
Version 1.1, 08/2013. Copyright
2013 Hitron Technologies
28
Hitron CGN3 User’s Guide
Figure 7:
The Setup Wizard: Setting Password Screen
The following table describes the labels in this screen.
2.3
LAN Settings
Use this screen to set up your CGN3’s Local Area Network settings, including its IP
address, subnet mask and DHCP status.
NOTE:
If unsure about how to configure the fields in this screen, leave them at their
defaults.
Click
Next
in the
Setup Wizard: Setting Password
screen. The following screen
displays.
Table 5:
The Setup Wizard: Setting Password Screen
Old Password
Enter the password with which you currently log into the
CGN3 for this account.
New Password
Enter and re-enter the password you want to use to log
into the CGN3 for this account.
Confirm New Password
Prev
Click this to return to the previous screen.
Next
Click this to continue to the next screen.
Page 29 / 114
Version 1.1, 08/2013. Copyright
2013 Hitron Technologies
29
Hitron CGN3 User’s Guide
Figure 8:
The Setup Wizard: LAN Settings Screen
The following table describes the labels in this screen.
Table 6:
The Setup Wizard: LAN Settings Screen
Private LAN IP Address
Use this field to define the IP address of the CGN3 on
the LAN.
Subnet Mask
Use this field to define the LAN subnet. Use dotted
decimal notation (for example,
255.255.255.0
).
DHCP Status
Use this field to configure whether or not the CGN3’s
DHCP server is active.
To turn the DHCP server on, click
Enabled
.
To turn the DHCP server off, click
Disabled
.
DHCP Start IP
Use this field to specify the IP address at which the
CGN3 begins assigning IP addresses to devices on the
LAN (when DHCP is enabled).
DHCP End IP
Use this field to specify the IP address at which the
CGN3 stops assigning IP addresses to devices on the
LAN (when DHCP is enabled).
NOTE:
Devices requesting IP addresses once the
DHCP pool is exhausted are not assigned an IP
address.
Page 30 / 114
Version 1.1, 08/2013. Copyright
2013 Hitron Technologies
30
Hitron CGN3 User’s Guide
2.4
Wireless Settings
Use this screen to configure the CGN3’s wireless network.
Click
Next
in the
Setup Wizard: LAN Settings
screen. The following screen
displays.
Figure 9:
The Setup Wizard: Wireless Settings Screen
Prev
Click this to return to the previous screen.
Next
Click this to continue to the next screen.
Table 6:
The Setup Wizard: LAN Settings Screen (continued)
19216811.live